Trip plow works great!

With a multiple bottom plow, you can simply measure the spacing between adjacent beams, directly crosswise and center-to-center. Don's comment wasn't about the plow size, but the diameter of the coulter disks themselves. For a number 8 plow, the originals were probably 16", although there was an option of 18". Due to wear, your old ones will probably measure a lot less than their original size.
 
Jim Becker":1ae97xd3 said:
With a multiple bottom plow, you can simply measure the spacing between adjacent beams, directly crosswise and center-to-center. Don's comment wasn't about the plow size, but the diameter of the coulter disks themselves. For a number 8 plow, the originals were probably 16", although there was an option of 18". Due to wear, your old ones will probably measure a lot less than their original size.
The reason I was asking about how to measure the plow is I wasn’t sure if the size of the plow would determine the coulter size
 
MiCarl":3r0pmeh2 said:
LittleBigTires1948":3r0pmeh2 said:
It was my test area and I ran outta room, I have clay and that was a hayfield with tall grass but I think I’ll widen the rear tires I think it’s too close the the next row

You don't need to widen the tires. You can shift the plow left and right by changing how the plow's hitch attaches to that crosswise bar with all the holes in it. You want to adjust the plow so the right lower corner of the right share lines up with the inside sidewall of the right tractor tire. Then when you drive with the right tire in the previous furrow the plow cuts the next furrow right against it.

Don't be tempted to cheat by moving the clevis along the draw bar. That pull from the plow will try to steer the tractor and you'll end up fighting it. For that matter, I wonder if it might be better not to use the swinging draw bar with the plow. Someone who knows more about that might weigh in.
How does this look for adjustment?
 

Attachments

  • CACD7DD3-FB9E-4B89-8169-E18C779FC1F0.jpeg
    CACD7DD3-FB9E-4B89-8169-E18C779FC1F0.jpeg
    34.6 KB · Views: 799
It may be camera angle or optical illusion, but the right hand bottom (as seen in the photo) appears to be set higher than the other one. Is that correct?
 
LittleBigTires1948":36ulyexm said:
How does this look for adjustment?

It looks pretty good. You might find you have to tweak it a bit once it's in the ground.

As Don pointed out, as it sits now it looks like the right bottom (in direction of travel, not how the picture is taken) will run lower than the left. Once it's in the ground you need to make sure they're both at the same depth.
 
[strikethrough][/strikethrough]
Don McCombs":2nhnke1k said:
It may be camera angle or optical illusion, but the right hand bottom (as seen in the photo) appears to be set higher than the other one. Is that correct?
It may be because it’s raised up and both were not at the same setting. And I think the photo Was taken at an angle and since they are not next to each other it appears that way, they are exactly how they were when I got it but I’ll check it with a level tomorrow
 
LittleBigTires1948":1kh1e08r said:
I’ll check it with a level tomorrow

Don't bother. It needs to be level with the plow lowered and the right and tail wheels in furrows. Raised, on flat ground, is meaningless.
 
Well I just meant to check if maybe the beam is bent or something wacky I just meant more as a straight edge than a level.
 
If you want some fun, be pulling that trip rope to raise the plow when it catches a rock and breaks away. It is amazing how long your arm can get before your mind tells you to let go. :roll:
 
John *.?-!.* cub owner":o2u3957y said:
If you want some fun, be pulling that trip rope to raise the plow when it catches a rock and breaks away. It is amazing how long your arm can get before your mind tells you to let go. :roll:
:mrgreen: I’ve heard about that, in fact a guy tore his seat off because he used some sorta 800 pound para cord and had no release mechanism I think it was on a super a and however the seat was attached was so rotted it failed.this happened on my buddy’s farm and his dad had a hell of a time running after the tractor and hitting the ignition.
 
Local fella using an H or M, don't remember which tied the rope to the seat using the heavy baler string for the older balers. He only weighed around 160 pounds or so and when the trip opened it pulled the seat quite a ways down before the string broke. Almost launched him over the steering wheel. Wish I ha a video of that. :lol:

Dad had welded a tab on the front of the plow clevis (twisted clevis), and attached a screen door spring to the tab and the front of the swinging drawbar so it would always be pointed to the rear after a break away. He had also mounted a handle on a pivot with a spring on the front and rear, that enabled the operator to hitch up without getting off the tractor. Sure was handy in our rocky clay.
 
So I’m not sure I have enough traction to actually disconnect the plow I’ve hit a few rocks while testing it And it stopped me dead but the tires spun although I have wheelied the the H skidding logs so maybe it was the ground I have one set of rear weights and front weights but I have another set of rears, I just wanna make sure the trip actually works, the plow it still in it’s current rusty state so I’m not sure if it’s stuck or if it can even be stuck, the hook wiggles a bit but I’m still clueless as to it’s operation.
 
I doubt it'd be stuck hard enough to not trip if it needs to.

I've done a little plowing with an H that has a single set of rear weights and a John Deere 2-14 plow. The only time the plow tripped off is when another operator dropped the clutch (he just cannot seem to feather a clutch!). We did manage to get wheel spin while plowing without it tripping off.
 
MiCarl":191ksrwq said:
I doubt it'd be stuck hard enough to not trip if it needs to.

I've done a little plowing with an H that has a single set of rear weights and a John Deere 2-14 plow. The only time the plow tripped off is when another operator dropped the clutch (he just cannot seem to feather a clutch!). We did manage to get wheel spin while plowing without it tripping off.
Ok good, I was kinda worried about that if i was plowing and my tires for some reason has more traction than normal I’d flip backwards, for all my tests I have had my foot hovering over the clutch just in case.
 
So my coulters measured 12” each they do seem to be contacting the sod and here’s how it’s turns
 

Attachments

  • 339282C9-519C-493F-BD5A-1CFD823DAB05.jpeg
    339282C9-519C-493F-BD5A-1CFD823DAB05.jpeg
    606.2 KB · Views: 497
Back
Top