Won’t start

nhess22

New member
While using my 72 Cub for some yard rolling a few days back I’d hopped off the move a couple of things and when I got back on and traveled maybe 50 feet my Cub just up and died on me and won’t restart. I noticed some sediment in the bowl so I siphoned the tank, cleaned the bowl and flushed out the fuel line from the bowl to the carb and cleaned it out as well. After all that and putting some fresh fuel in the tank it won’t restart. Engine turns over but isn’t getting any spark. Any ideas if it’s a bad coil or if the points could be bad? Any help would be greatly appreciated.
 
While using my 72 Cub for some yard rolling a few days back I’d hopped off the move a couple of things and when I got back on and traveled maybe 50 feet my Cub just up and died on me and won’t restart. I noticed some sediment in the bowl so I siphoned the tank, cleaned the bowl and flushed out the fuel line from the bowl to the carb and cleaned it out as well. After all that and putting some fresh fuel in the tank it won’t restart. Engine turns over but isn’t getting any spark. Any ideas if it’s a bad coil or if the points could be bad? Any help would be greatly appreciated.
I'd start with the points and clean and regap them to spec which I think is .020. After that check for corrosion on distributor cap and rotor and so forth.
 
Ensure that the main jet is not obstructed by sediment from the tank/bowl. Check for spark at the plugs and work back toward the source if no spark. JMHO Stan
 
When everthing was fine and it dies fast and will not restart I had the spring for the points break. I had that happen twice. That is when I stopped using tractor web site points bought NAPA

[td]napa points ECH CS1600[/td] [td]napa Condenser ECH IH200[/td] [td]napa Rotor ECH IH300[/td] [td]napa Cap ECH IH350[/td] [td]napa Plug CHA 549 D18Y ( projected) CHA 502 ( non projects)D21[/td] [td]napa oil; filter 1153[/td] [td]napa VR 6 v VR851[/td] [td]napa coil 6 ECH IC7[/td] [td]napa coil 12 ECH IC14SB[/td]
 
I agree with Stan. My guess is the coil, but start with points and condensor.
When testing a coil for spark remember to check both the points and the output to the plugs. I had a coil failure that had spark at the points but none to the plugs. The cause was a failure in the high output winding. Replaced the coil resolved the problem. JMHO Stan
 
In 50+ years with the cub, points have yet to be my cause for no start. Coil has always been the electrical fault. Clogged main jet has been the mechanical fault.
 
Sudden death with total loss of spark often points to the primary wire shorting to ground right where it passes through the distributor housing. That insulator bushing gets brittle and cracks with age. Condenser failure fits the symptom too, worth swapping.
 
Update: checked the points and cleaned em up with a wire wheel on my dremel. Hasn’t fired up yet. When trying to start it I could smell fuel, so it’s definitely getting fuel. It appears it was converted to a 12 volt starter by I’m guessing the previous owner. What would be the next logical step to check.
 
It appears it was converted to a 12 volt starter by I’m guessing the previous owner.
Hi,
A 1972 Cub is originally 12 volts.
IH changed Cubs to 12 volts during 1964.
Your Cub should have a 12 volt battery, starter, generator, lights, and everything else.

I would test the power of the spark the Battery Ignition unit is making.
Below is info for checking the spark, if you need it.
Be sure the Cub doesn't roll while doing the spark test.
Remove the ignition wire from the center post on the distributor cap, and hold the wire by the insulation, with the metal end about 1/4" from bare metal of the engine block.
Be sure the transmission is in neutral, turn the ignition switch to on, and run the starter.
The spark should jump the 1/4" gap, and be blue or white. A yellow spark is weak, and needs improving.
The engine may not run, or run right, with a yellow spark.
Do the test in a building, or not in bright light, so you can see the spark well.
The battery should be fully charged for the spark test. Charge the battery if necessary.
A low output charger is better, it may take several hours to charge it.

Below are pages from the 1965 Cub and LoBoy operator's manual, showing the original size battery, and 12 volt starter and generator. The manual has 6 and 12 volt info, disregard the 6 volt info. :)
https://farmallcub.club/rudi/farmallcub.com/rudi_cub/www.cleancomputes.com/Cub/Cub%20Owner's%20Manuals/International%20Cub%20&%20Lo-Boy%20Operator's%20Manual%207-29-65/Page-25.jpg

https://farmallcub.club/rudi/farmallcub.com/rudi_cub/www.cleancomputes.com/Cub/Cub%20Owner's%20Manuals/International%20Cub%20&%20Lo-Boy%20Operator's%20Manual%207-29-65/Page-26.jpg
 
Last edited:
A similar problem. My '49 Cub (6V magneto) died while idling and have been unable to restart it. Fuel is not the problem. Pulled a plug and saw it is sparking, but the spark seems weak. Not the least bit of a pop when cranking. Prior to dying it had a bit of misfiring when idling but not under load. Not good with electrics and am mystified.
 
A similar problem. My '49 Cub (6V magneto) died while idling and have been unable to restart it. Fuel is not the problem. Pulled a plug and saw it is sparking, but the spark seems weak. Not the least bit of a pop when cranking. Prior to dying it had a bit of misfiring when idling but not under load. Not good with electrics and am mystified.
Those symptoms sounds like you are dealing with a failing mag coil or a short to ground. JMHO Stan
 
A similar problem. My '49 Cub (6V magneto) died while idling and have been unable to restart it. Fuel is not the problem. Pulled a plug and saw it is sparking, but the spark seems weak. Not the least bit of a pop when cranking. Prior to dying it had a bit of misfiring when idling but not under load. Not good with electrics and am mystified.
have you checked cylinder compression?
 
did you set the points gap to .020 ? points should be filed flat, with the ignition on just open the points with a screwdriver to make sure you have spark there
 
A similar problem. My '49 Cub (6V magneto) died while idling and have been unable to restart it. Fuel is not the problem. Pulled a plug and saw it is sparking, but the spark seems weak. Not the least bit of a pop when cranking. Prior to dying it had a bit of misfiring when idling but not under load. Not good with electrics and am mystified.

There are 2 different ignitions being discussed in this post.
nhess22, the Battery Ignition point gap is .020"
capefarm, the magneto point gap is .013"
Both when the movable point is on the high part of the cam.
I would do the spark test that I posted above, it is easy to do.
Capefarm, the magneto is not hard to work on. The 1949 Cub owner's manual tells how to check or replace the points. The points burn from use, and eventually the engine won't run if nobody has checked them for years.
NAPA has new points, they are CS1600.
The condenser may have gone bad too.
The old original coils commonly quit, some get weak and don't make enough spark for the engine to run.
TM Tractor Parts has a new magneto coil, they are different than a car coil from the past. The coil is under the cover on top of the magneto.
Below is their listing for it, you can look at the pictures. I would begin by checking the points.
I sent you a message.
TM Tractor Parts for McCormick Farmall Cub, International Cub, and International Lo-Boy

Below is a picture of the magneto points and condenser.
The 2nd picture is the rotor drive gears. When the cover is off, you can clean the area, and grease the gears. Check the gear teeth for wear, if they are worn lots, the rotor and drive gear should be replaced. TM Tractor Parts has those.
Check the timing marks on the 2 gears, they should be aligned.
 

Attachments

  • Cub magneto 8.jpg
    Cub magneto 8.jpg
    25.1 KB · Views: 2
  • Cub magneto 4.jpg
    Cub magneto 4.jpg
    25.1 KB · Views: 2
There are 2 different ignitions being discussed in this post........
In addition to Glen's information you can access the ignition systems information GSS 1012 by clicking on the Resources tab link at the top of this page and download the manual. It will explain the ignitions systems, how they work and how to service/adjust and maintain the battery and magneto systems. A picture of the cover page is attached. JMHO Stan
 

Attachments

  • GSS 1012 man cover.jpg
    GSS 1012 man cover.jpg
    305.6 KB · Views: 2
Back
Top