What happened at work today.

Welded a fancy bending jig to the table and heated some 5/8” hot rolled to make some new rear lifts rods for both our 140’s.
 

Attachments

  • C55FEBB9-4364-45A9-8D9B-E0013D0B0049.jpeg
    C55FEBB9-4364-45A9-8D9B-E0013D0B0049.jpeg
    124 KB · Views: 2,599
  • F5D45D1B-E0D8-4DD0-BCD5-EDA4F5EA3D1A.jpeg
    F5D45D1B-E0D8-4DD0-BCD5-EDA4F5EA3D1A.jpeg
    185.3 KB · Views: 2,599
  • 5D41B187-1649-40CA-9CF4-789D4AED9BC1.jpeg
    5D41B187-1649-40CA-9CF4-789D4AED9BC1.jpeg
    143.4 KB · Views: 2,599
  • B1B0BC79-6670-4F5B-AA35-F111141351F0.jpeg
    B1B0BC79-6670-4F5B-AA35-F111141351F0.jpeg
    135 KB · Views: 2,599
  • E8AC25AE-C81C-45BC-A1BD-156DB89EA49E.jpeg
    E8AC25AE-C81C-45BC-A1BD-156DB89EA49E.jpeg
    99 KB · Views: 2,599
  • BC75D094-6DE0-4D05-9E1E-C440A5684AD0.jpeg
    BC75D094-6DE0-4D05-9E1E-C440A5684AD0.jpeg
    151.1 KB · Views: 2,599
Very nice. How did you know where to place the pieces for the jig before welding? I know those parts aren't exact fit, so did you just eyeball it? I should make a similar jig myself......wouldn't be very hard. Also, do you plan to make the little set screw stop clamps and the swivel? piece? If so, I'd like to see your design on those.
 
I did some measuring on the original piece as to where to weld this fixture. I've done several and just eyeballed it, you can always trim some of the length off if they're too long. I reused my old collars, they were in good shape. My rods were bent and one had been welded back together is why I made some new ones. I had to get a 20' piece of material so that's another reason I went ahead and made four.
 
Shane N.":2qjdiqu9 said:
I did some measuring on the original piece as to where to weld this fixture. I've done several and just eyeballed it, you can always trim some of the length off if they're too long. I reused my old collars, they were in good shape. My rods were bent and one had been welded back together is why I made some new ones. I had to get a 20' piece of material so that's another reason I went ahead and made four.
Sounds good Shane. At the cost of good used ones on eBay, it would pay me ahead to make new ones......especially since I have a few cultivator sets short those pieces. I just need to come up with the other parts such as the correct spring and the swivel piece. The collar style clamp would be easy.
 
Just playing a little.
 

Attachments

  • C66C1A89-49E1-41C1-9F8D-1E7E9449CB13.jpeg
    C66C1A89-49E1-41C1-9F8D-1E7E9449CB13.jpeg
    209.7 KB · Views: 2,417
  • 9EA2713E-612B-42ED-895C-B4CE0D0DF5AE.jpeg
    9EA2713E-612B-42ED-895C-B4CE0D0DF5AE.jpeg
    152.9 KB · Views: 2,417
Done with the new toy. It’s a miniature arbor press.
 

Attachments

  • 35B6A91F-1A2F-4ADD-BFA0-39245AB10522.jpeg
    35B6A91F-1A2F-4ADD-BFA0-39245AB10522.jpeg
    130.4 KB · Views: 2,328
  • 0EAD0CAB-46B1-428E-921B-3681EFC3B0CF.jpeg
    0EAD0CAB-46B1-428E-921B-3681EFC3B0CF.jpeg
    161.1 KB · Views: 2,328
  • 49787CA3-A23F-489E-A46B-73BE8272B23C.jpeg
    49787CA3-A23F-489E-A46B-73BE8272B23C.jpeg
    101 KB · Views: 2,328
  • 5A65D2C6-96F2-42D0-9C9D-831791B8D784.jpeg
    5A65D2C6-96F2-42D0-9C9D-831791B8D784.jpeg
    135.1 KB · Views: 2,328
  • 380CDA5C-F061-4B5D-B39B-473665BADADC.jpeg
    380CDA5C-F061-4B5D-B39B-473665BADADC.jpeg
    142.1 KB · Views: 2,328
Here it is with the table top and also the floor model and a 12 ounce can.
 

Attachments

  • 89D10082-0906-46BB-8CFA-D51F4CBB6771.jpeg
    89D10082-0906-46BB-8CFA-D51F4CBB6771.jpeg
    148.8 KB · Views: 2,328
  • 0C25BE1F-E518-4255-B53B-F8F8A2A59F71.jpeg
    0C25BE1F-E518-4255-B53B-F8F8A2A59F71.jpeg
    152.3 KB · Views: 2,328
Steve Butram":io9463hr said:
nice work. Is it intend to be used for a project in the shop
Thank you. I will use it for pressing small dowel pins in and whatever else it comes in handy for.
 
Very imPRESSive :D I'd like to ask a technical question. Did you build it around a section of rack or did you cut that too? Either way, you had to cut the pinion teeth so that was some precise work too.
 
mozer71":3mcspown said:
Very imPRESSive :D I'd like to ask a technical question. Did you build it around a section of rack or did you cut that too? Either way, you had to cut the pinion teeth so that was some precise work too.
We’ve had the rack for a long time and I found a gear in an old desk drawer the other day. That’s what gave me the idea to make this.
 
Very neat and I like the open base and plate you made. These are often with an accurate hole right up the arbor, only a short depth. You can turn any diameter of pin or foot to reside there. fwiw, I have a Dake Engine Co. model X which I think is one of their smaller arbor presses. It doesn't have the open base but threaded holes for some fixture. That limits the uses we would apply.
 
Went out to my truck to check on something and there was a box truck parked next to it and I noticed the right rear tire was slack and had some steel showing. Upon further inspection the one that is slack actually isn't that bad compared to the one beside it.
 

Attachments

  • AD1A0A40-CB58-4418-ACD1-F592D5327DF9.jpeg
    AD1A0A40-CB58-4418-ACD1-F592D5327DF9.jpeg
    163.1 KB · Views: 2,655
  • 17D26626-EC1D-43F7-BFB6-7871BDA5AB2F.jpeg
    17D26626-EC1D-43F7-BFB6-7871BDA5AB2F.jpeg
    139.1 KB · Views: 2,655
Back
Top