Square Sockets?

dgrapes59

501 Club
OK, odd question... does anyone know if anyone makes a socket, 1/2 or 3/8 drive, that fits square nuts or bolts? I have never seen one, but with the talent on this forum, if it is available I am sure someone will know!

This kind of relates to my Windmill project... it is put together with square nuts/bolts and this sure would make the dissassembly / assembly much easier.

Thanks,

David
 
Thanks I thought a 12 point would work, but if a square one was available it might be better on those bolts that probably have not been turned in 75 or more years (especially if I use one of those "really powerfull impact wrenches" :D
 
Yes. But the individual sockets are expensive. You might try an industrial supply store.

Penetrating oil and an adjustable wrench (Cresent wrench) works just as well.
 
I will loan you my 1" drive breaker bar to use the sockets on!!---IF you can lift it! LOL!!!----I do have a 1" drive imported socket set and have used it a LOT over the years!----it goes from 1-5/8" all the way to 3-1/8", has ratchet and bar!---real handy set! thanks; sonny
 
I have 8 point sockets in 1/4, 3/8 and 1/2 inch drive Snap on, Craftsman, and Williams brands so I know they are out there, but will probably be difficult to find, I doubt if you find them at Lowes or Home Depot.

I haven't seen your windmill up close but I'm willing to bet that it will unbolt a lot easier than you expect. I have had a fair amount of experience with old square nuts and bolts, unless they have a lot of thread showing, they are almost always difficult to break loose but then unscrew easily, or they readily break off. Most of the ones with a lot of thread showing are difficult to break loose and the more you unscrew the harder they are to turn, until they break off, for the long ones if you want to save them, once they break loose, work them back and forth as you unscrew (if you have to work them back and forth they are more easily done with wrenches).

The biggest problem I have found with them is that often times the head of the bolt and the nut as well seem to be tapered a little, and your socket will want to get crooked on the nut or bolt head, then it will want to slip off (this part of the operation is normally painful).

Best of luck with your project and keep us posted as to your progress.
 
One of my Christmas gifts was one of the "gator" sockets that fits on a 3/8" drive. It has a bunch of round pins in it, and will fit to the size and shape you need. Works good and works on stripped and rounded nuts and bolts too.
 
Craftsman will have 8 pt sockets up to 3/4 inch. If you need larger ones, Snap on, Mac, or Matco and they get a little spendy.If you are an Ebayer, I've seen them there on ocassion.
The smaller sizes are great when you need to run taps or reamers.
 
Thanks guys, I should be covered now! The bolt heads are only about 9/16, or 5/8 at the biggest, so I don't think I will need to take Sonny up on his offer for the 1" drive stuff! The bolts threads don't extend much past the nut and are galvanized, so hopefully there will be minimal stubborn ones (probably less than I had on my Cub!). I had kind of asked this question with the intention of using my 18V dewalt impact to save some time and effort if I was hanging on the tower. (the more I think of this, the more I think it will be a job for my fireman son-in-law :lol: ). Thanks again to all!
 
Many of the old timers believed in greasing (before the invention of anti-seize) the threads on bolts to keep them from seizing, because they expected the stuff to be around a while, not used a few years and then thrown away. It keeps them free for a long time.
 
I have a craftsman set of square sockets i believe there 8pt. That craftsman impact gun (110v) with a genny would do the job too. Its got 200ft.lbs of force i believe too. I was never a believer of the electric impacts until i ran the ingersols many years ago. Now i swear by them. If there really stubborn a little heat will do too. Just heat one side of the nut so half the hole will expand. If you heat the whole nut everything gets hot even the bolt too.
 
Dave, I found a set of Craftsman 8-pt square sockets (3/8 drive) on E-Bay a couple of years ago for a reasonable price and use them all the time. Great for drain plugs in addition to those square nuts. :D :D
 
Back
Top