shrink wrap avoid it like the plague

scotlem

501 Club
I was going to post a picture of this but couldn't figure out how to get it transfered from my phone to the computer. shrink wrap for those who aren't familiar with it, is that saran wrap like stuff that they wrap around stuff on pallets to hold it all together for shipping. If you go into Home Depot and look up into there overhead storage shelves you will see it there. In several layers it is very strong but when torn off and thrown on the ground it is very light and wispy. And when you get rotating equipment especially with cooling fans such a cars, trucks tractors and fork lifts it snatches it right up and spins around the shaft tightly. Working as a mechanic in a lumber yard I've seen it destroy all types of bearings and seals including Alternators, water pumps, Idler pulleys, cooling fan bearings, and front main seals. This time it was a fork lift front main seal. In order to replace the seal I had to remove the vibration damper and front cover which in turn required me to remove the oil pan. After removing the oil pan I found shrink wrap had passed threw the front main seal shredded into pieces and had almost completely closed off the suction screen of the oil pump. The moral of this story is if you see this stuff on the ground at your work or at your home pick it up and get it into the trash. If see it on the road, in a parking lot, lawn or field don't run over it with your car truck lawn mower or tractor avoid it like the plague. also similarly hazardous is those light plastic shopping bags you see blowing around on a windy day.
 
Good advice, Scot! I've seen plastic grocery bags, wrapped around lawn mower spindles, tight enough to stop the rotation. Difficult to remove, for those of us without a ten ton toolbox. Ed
 
Thanks Scot. I love it when I'm driving down the road and the car ahead of me blows a bag upwards and it finds it's way onto the front of my truck closing off the radiator air :shock: Everytime I drive over a bag now I look out my mirror to make sure it keeps on blowing :D :D Gotta love plastic!!!!

Rick
 
Yes that shrink wrap is good for its purpose , but must be discarded properly, however that does not always happen.
I remember hearing a story of a lady driving her car and ran over a large plastic grocery sack. It did not come out as Rick mentoned , but melted on the catalytic converter , everytime the car exhaust reached metling temp the fumes were so bad her Eyes burned.
She took it to a mechanic , wondering what the smells were coming from , not remembering she ran over a plastic bag, it melted on tight !!, so much that the mechanics could not get it off with out replacing the converter. Several hundreds of Dollars later .
So I take the advice given , that if you have any plastic on the road or near your equipment ,either make sure they are picked up or make sure the bag comes out the back of your vehicle.
My.o2
phil
 
Thanks. I'll second the statement about getting it wrapped up in your exhaust. Even after scraping it off, it still has to finish burning before the smell goes away. Grump
 
I borrowed a friends Kubota tractor with a rototiller for doing my garden. I noticed there was stuff wrapped around the shaft and tines when I picked it up. Before I returned it, I decided to clean things up :shock: I spent neary an hour, with a sharp knife, laying on the ground cutting the visqueen off the shaft. It was wrapped around so tight it semed like it was melted together.

Rick
 
I kills a lot of marine life too. There are places in the middle of the ocean where the currents have deposited a huge amount of this junk. One year I did not pick up my Mason's line in my garden And that was a similar mess when it was caught up in the Gravely. Nothing like getting the plastic in the engine, though. That is one for the books.
 
Its become pretty common place for me. The fork lift I just did, had the front main seal replaced in 06 for the same reason. While I was looking at this one trying to find where the oil leak was coming from not 50 feet away from me I hear a flapping noise and I see a fork lift operator jump off an Identical fork lift and started pulling shrink wrap out of the fan. I have other lifts that the oil light tends to flicker a little at low Idles that I can't help but wonder if they have suffered the same fate with shrink wrap in the oil suction screen. I showed it to the boss and to dispatch but it won't make a difference. Me, I don't like to replace bearings bushing and seals, just because. Especially in my own P/U. So when I'm walking through the lot I pick up after them.
 
Back
Top