Sharpening Lathe Cutting Bits

Paul_NJ

501 Club
I mentioned in an earlier post that I had been given a very old metal lathe, which appears to be a 9 inch Atlas.

IMGP0739-vi.jpg


I'm currently in the process of soaking out old hardened grease, removing rust prior to painting, finding broken part replacements, etc (sounds just like another Cub project, doesen't it?) and have picked up a couple books on metal lathe work. From what I've read, the tool bits have to be ground very specifically for what you wish to do, and with very specific angles, back cuts, etc required to do it right. Frankly it sounds extremely complex! Unfortunately the books (Atlas, and Lindsey's South Bend) I found have really small photos of what they're talking about, and illustrate countless configurations.

How do you learn how to do this? Are there good books with huge photos that take you thru grinding the bits step by step? Can you buy ready made bits . . . perhaps I could use them as a sample to work from? (As you can see from the photo, the lathe has a sort of carousel arrangement that holds 4 cutting bits. I recall GW pointed out the last time that this arrangement is better than the lantern or Armstrong schemes.)

But where do you start? I would appreciate any suggestions on how to begin learning this. I've never done this before! Help!

P.S. for George Willer: My 340 has disc brakes . . . there are two cast disc's inside each housing, probably the same as with your Super M, and they're pretty glazed. It occurred to me that maybe (if I ever learn how to make a cutting bit, that is) I cut them on this lathe like you would on an brake lathe? Have you ever done this? Would it be worth doing?
 
Yes there are specifics, the only thing you have to really concern yourself with is the clearance of the tool bit to the work piece, and make sure it is relieved so it makes contact @ the cutting edge. there is an minimum rake angle.
aluminum is greater than steel as long as you have it cleared , read up and start cutting.
You can read all the books you want, but until you do it you will not always see the problems encountered. So get the basics grind one up and give it a whirl. If it has automatic feed I would keep it off until you gain confidence with it.
One more thing, Rick Prentice and I were talking @ GW's sat about leaving the chuck key in the lathe jaws , This is and absolute No NO
So be careful. no loose clothing etc.
Phil
 
The brake disks should be really hard metal, so take very light cuts until you see what they try to do and probably will want to turn them slow, too!!Thanks; sonny
 
Sharpening lathe bits according to a book can be frustrating. They give you a lot of nonsense about angles, etc. that are meaningless until the holding method is known. The commonly used Armstrong tool holder introduces an angle to the tool bit that must be accounted for when sharpening. What's important is the actual cutting and clearance angles of the cutting edge relative to the work.

PWL is right... try what works and then try to duplicate it. The books will be the most help determining cutting speed and feed. At least as a beginner slow will usually be a lot better than production speed.
 
George Willer":381rehfw said:
Sharpening lathe bits according to a book can be frustrating. They give you a lot of nonsense about angles, etc. that are meaningless until the holding method is known. The commonly used Armstrong tool holder introduces an angle to the tool bit that must be accounted for when sharpening. What's important is the actual cutting and clearance angles of the cutting edge relative to the work.

PWL is right... try what works and then try to duplicate it. The books will be the most help determining cutting speed and feed. At least as a beginner slow will usually be a lot better than production speed.

George

I wish I lived an hour or two away so I could come and be your apprentice for a week. Now, I don't have an Armstrong tool holder, but rather a 4 way, which I recall you told me was a good thing. Since I can't stand there and look over your shoulder, how do I start using this lathe? Should I buy a bunch of blanks, and try grinding them, or some ready-made ones and go from there? If so, is there a common "generic" I could start with? Do you have a bed in that barn of yours? I think a week with you might at least get me started!
 
Couple of thoughts.

1) See if you can find some old highschool shop text books covering metal lathes. Most are fairly easy reads.

2) The first couple of tool bits - purchase pre ground. The rest - buy the blank bits and grind your self. Blanks are very cheap.

Eugene
 
Thanks guys. Bob and Eugene . . . sounds like your suggestions to buy a couple in the beginning may be the best place to start . . .
 
Paul, you will need carbide to cut those discs. You may as well buy 2 left, 2right, and 2 60deg carbide bits. center up on your workpiece, note the clearance angles and duplicate those angles on HS steel bits. this will give you a starting point, you will probably want slightly more relief on the HS bits. I would recommend that you do not grind a top relief or back rake on your HSS bits until you have some experience. Older worn, and smaller lathes tend to have the toolbit suck into the workpiece if the bits are ground with back rake.
Another reference I recommend is Machine Tool Technology by McCarthy& Smith published by McKnight&McKnight. This was the textbook used by many schools a few years back and is an excellent reference for all machine tools.
 
Phil,

I have an old Craftsman lathe that I bought from my uncle. He made a switch that you actually had to insert the chuck key in to run the lathe. Actually this is a very nice feature because you always know where the key is and you will never have to duck to avoid a flying chuck key! :)

Brian
 
Back
Top