Reloading ammo

Jackman

501 Club
Anyone into reloading ammo? I'am going to venture into reloading for obsolete vintage ammo so I am gathering info on what to to buy seems there are several types of manufacturers and press types too , so far I think I want a single press made by Lee or Rock Chucker I hope to buy this stuff used its a bit pricey new. Plan to do light target loads for .38 acp , ,45acp and .center fire .22 rounds and probably add more obsolete stuff as I add to my collection .....
 
If you are going to get serious into the obsolete stuff you need to make sure the press has enouhg leverage to resize/reshape cases for different calibers since much of the old brass is no longer available..
 
Buy the Rockchucker, had mine for close to 40 years it has loaded thousands of rounds, still works great. Also have a couple Lee turret presses that are set up for pistol ammo. Lee presses may get the job done but just aren't RCBS quality. Nothing wrong with buying a used one or for that matter Pacific and Redding also make good presses. If you decide on Lee try this: info@factorysales.com.
You might try www.gunbroker.com they have new and used presses You might also find obsolete brass there. If you have problems navigating their website let me know.
 
Jackman i agree with lilred i have used the rockchucker for a long time and i like the RCBS dies i have the old style powder scales but the new digital ones i hear are real good.

Jim
 
I used a Lee turet press before I upgraded to my Dillon with good luck although I was only loading 38 Specials.

John's point is well taken. If you have to do much resizing, you will want something with more leverage than the Lee.
 
I have a RCBS Rockchucker since the 70's with no wear yet. Since the rcbs dies have become so expensive now the LEE dies fit the RCBS press. If your going to do massive reloading go for the rockchucker. We run about 5k of 308win at a time. The LEE reloading kits are good too. I like the LEE Pro 1000 progressive press for my 45acp. I hope to set up all the handgun calibers we shoot for the lee pro 1000(die plates). For handguns go for the carbide sizing/die sets no lubing.

If you had your C&RFFL03 license you get discounts at http://www.midwayusa.com and brownells too.
 
I really don't know what you guys mean by leverage , I plan to just buy several hundred rounds of 38acp and the .22 center fires and just reload them as long as possible unless of course I find a source for the brass casings,

Here are the two units I am looking at the Lee is most likely one I will buy on account of the afordabilty factor but the Rock Chucker has a lot of good reviews.

http://cgi.ebay.com/LEE-50th-Breech-Loc ... 1342wt_906


The Rock Chucker http://www.gandermountain.com/modperl/p ... rchID=4005
 
Watch http://www.midwayusa.com for sales and deals on the LEE starter reloading kits too. I also like the LEE case trimmers we use with a battery operated drill. Your going to need a case tumbler too. I use the frankfort vibrator for case tumbling. (midwayusa has these on sale at times too)


I'm using the smaller LEE presses for secondary work on the brass. They have been awesome too. (decapping with the LEE decapper die. I'm sure the larger LEE press will serve you well and won't break the bank buying it. I been buying up the LEE RGB dies too. The 308win RGB dies was only $9 at onetime and we flew 5k of 308win thru it twice now. The LEE dipping cups help out too. I pick the next size smaller cup size thats under my load and then use the powder trickler to make each load exactly the same. I ran all the 308win this way. I have over 10k of match grade ammo. Bill

Right now were just shooting my 1978 45acp ammo that i reloaded way back then. It all goes bang like the day i reloaded it. I have some surplus 8mm turkish fmj ammo dated 1937 that all fires off too. My point is the shelf life on ammo is many, many years. I do store it all in 50cal ammo cans so there dry.

My reloading process;

1st. Decap the brass
2nd Polish the brass with the coarse media
3rd. Lube & Resize the brass
4th Wipe the lube off the resized brass
5th Trim the brass to its orginal length
6th Clean out the primer pockets
7th Back to the polisher with the fine media and brass polish
8th Inspec the primer pockets for media stuck in them and make sure the inside of the cases are free of media
10th Prime cases
11th Look in the reloading book for a powder weight for the bullet your using and Charge the cases with gun powder( you can weight each load or set the powder dispensor to that powder weight) I check and double check the powder dispensor before the run, during the run to make sure its still correct. Remember to zero the scale before you set the powder weight.
12th Insert the bullet and seat it.(if you need a crimp most dies will do it once you set the bullet dept you can back off on the seater rod and lower the die a tad to add a crimp then while the arm on the press is down set the seater rod to the bullet thats already set and lock it. Then try one round to see if its all set correctly, if it is run them.

No 1 rule don't talk to anyone while reloading, no distractions, no mistakes. If your powder charging leave no unopened cans of powder nearby while reloading and clean up all the spilled powder on your table when your done. Clean up the4 floor too. Do not use a vaccumne cleaner use a dust pan and a brush. besafe do it right and proceed with caution. Bill
 
Thanks Bill, thats some good info I do appreciate :big afro: , looking forward to getting started we set up a nice oak loading bench with a plexi glass sheet and a side rail too safety is a big concern here (basement set up) along with learning the ways of reloading. Any advice on loading light just for targets :?: , I am thinking that these hand guns a Colt model 1906 and a Colt model 1911 are 106 and 93 years old a lighter charge might be a way to keep them in good operating condition :idea: , however the local gunsmith says just use them no need to load light he checked them both out and says there fine but still old is old and we are only shooting paper targets.
 
Jackman":271apazt said:
I really don't know what you guys mean by leverage , I plan to just buy several hundred rounds of 38acp and the .22 center fires and just reload them as long as possible unless of course I find a source for the brass casings,

Here are the two units I am looking at the Lee is most likely one I will buy on account of the afordabilty factor but the Rock Chucker has a lot of good reviews.

http://cgi.ebay.com/LEE-50th-Breech-Loc ... 1342wt_906


The Rock Chucker http://www.gandermountain.com/modperl/p ... rchID=4005
http://www.gunbroker.com has a section for brass, you might also try Graybeard Outdoors There is a forum for buying and selling reloading items.
 
Both the Lee Cast Press and the Rock Chucker are fine presses. I've managed to break an Lee Challenger press in my lifetime, so if you are really thinking you will be forming your own brass, go with something strong. If you are just thinking pistol rounds, they don't need so much strength in the press for them. My best advice is for someone to show you how to do it the first time or two. Of course buy a good reloading manual and read it, once away from the press and then again when you get ready to reload. :D
 
Back
Top