Poulan Chainsaw

You have to watch for quality products from name brand name producers also. Not sure about Stihl but Husqvarna has what they call the homeowners series ( like the ones sold in boxstores). They have plastic crankcases which I guess would be ok for occasional use. Beware of what you buy now because the days of producing one quality product are almost gone. It is all about the profit margins now.
 
Eugene":1hrrpqz2 said:
Boss Hog":1hrrpqz2 said:
I think Boss Hog gets a commission for every time he mentions Stihl products.

I have two each Stihl chan saws. Used both today. One is about 20 years old and the youngest close to 15 years old.

The saga. I got one of the Poulan chainsaws running without any big problems. The second one I got running once. It was running very lean and hot. Shut it off, then it wouldn't start. Cleaned the carburetor, changed the plug, etc.. Engine cranked over, excellent compression, spark. Still no start. This morning fuel up the saw and went out side to try and start it again. Locked up tight. Dumped the fuel back into the gas can. Figgled with it checking the crankshaft rotation. Still locked up. Banged the front of the saw down at an angle. Saw freed up.

Complete tear down time. And probably pitch in the trash.
Moral is to purchase quality products. Cheap frequently turns out to be very expensive.

Yep right there with Case/IH and NAPA , you would think I have stock in the Co. :D by the way Alt.s took a price increase :oops: I have to pay $50 for one today

Boss
 
Adjusting the carburetor on the Poulan chainsaw is not listed or even mentioned in the owners manual.

Reference: http://www.epa.gov/otaq/consumer/f98025a.pdf

Page 2. Can I make adjustments to the new engines at home?

Consumers should perform routine use and care maintenance as recommended in the operator’s manual. However, owners should contact a qualified engine technician
for adjustments not listed in the operator’s manual. Owners should also be aware that it is against the law to tamper with an EPA-certified small engine. Tampering with a certified engine may involve adjusting the fuel or exhaust system, or changing the engine’s performance so that it no longer meets the manufacturer’s specifications. Tampering may increase an engine’s exhaust emissions, contributing to our air pollution problems. To stop customers and repair facilities from tampering, manufacturers have equipped many engines with special caps or plugs that limit or prevent adjusting the fuel mixture or engine timing. Removal of these special caps or plugs and adjustments beyond the manufacturers specified limits are considered tampering and may subject the violator to a fine.
 
Eugene":18i6b7sf said:
Page 2. Can I make adjustments to the new engines at home? . . .
That paragraph is interesting. I never found that document when I looked on that site.

I notice it is pretty full of "should" and "may". The only sentence that doesn't use one word or the other is
To stop customers and repair facilities from tampering, manufacturers have equipped many engines with special caps or plugs that limit or prevent adjusting the fuel mixture or engine timing.
Note that it says "many", not "all". In other words, manufacturer's option.

Clearly, they are trying to discourage end users from "tampering" with the adjustments. But the manufacturers don't appear (my weasel word) to be REQUIRED to prevent a user from turning an adjustment. If you do make an adjustment that puts the engine out of compliance, you are responsible for it. But I still don't see anything that prohibits the manufacturer from selling the fancy screwdriver.
 
The way it was stated to me by a former Poulan guy, was that Poulan did not allow dealers to sell the tool, not that there was a law against it. I assume the way I posted made it sound differently.
 
John *.?-!.* cub owner":l1e3eqv9 said:
The way it was stated to me by a former Poulan guy, was that Poulan did not allow dealers to sell the tool, not that there was a law against it. I assume the way I posted made it sound differently.
It is the Poulan web site that very clearly and very incorrectly said there was a law against it. He even quoted how much the fine is.
Manufacturers will not be able to sell these tools to consumers. Again due to EPA regulations anyone caught selling this tool to an individual can be fined up to $3500 for each offence each day the tool is in service.
 
Boss Hog":2f02e0kw said:
:D by the way Alt.s took a price increase :oops: I have to pay $50 for one today

I got mine on wed and it was $45. I checked with O'riley's and the # crosses over to a "Wilson" brand? $65
 
Back
Top