Poulan Chainsaw

Eugene

501 Club
I'm working on my brother's Poulan chainsaw. I need to tweek the carburetor and it takes a special tool to adjust the carburetor.
On the internet. Question by a Poulan chainsaw owner to Poulan. "Why don't you provide a carburetor adjusting tool with each saw".
Thanks for using Answer Army. Due to EPA Government Regulations only dealers / service centers will be able to adjust carbs. Manufacturers will not be able to sell these tools to consumers. Again due to EPA regulations anyone caught selling this tool to an individual can be fined up to $3500 for each offence each day the tool is in service.

I know this is not the information you wanted to hear but you can go to epa.gov to read more on this.
What a crock of chips.
 
RaymondDurban":1fs4tl7m said:
Do the high and low adjustments have the plastic caps on them that don't allow more than like 1/8" turn?
No. The adjustment screws have a head that looks like a very fine toothed gear. No slot for a screwdriver or socket for allen wrench. It going to take a small, very thin walled special socket to fit over the adjustment screws.
 
Sounds like some type of knurling. Maybe you could make a tool with a piece of soft copper(?) tubing that isn't quite big enough to slip over the head. Then flare the end at a very gentle angle so it will just slip over the head. If it doesn't turn too hard, the tube may be able to grip it with a little pressure onto the head.
 
Eugene:

Is this the link to that tool? POULAN CRAFTSMAN CHAINSAW CARB ADJUSTING TOOL SPLINED I have a Poulan. Be nice to have the right tool to maintain it when required.

!Bg0v80gCGk~$(KGrHqQOKiYErzLE)F+!BLGwbTUirQ~~_1.JPG
 
Thanks Rudi. That is the tool. I saw it on the internet. I'm just to cheap to pay for the tool and the shipping. Next trip to the big city I will try a major sized small engine shop and the big box stores.

What I wonder is why the tool is not available for chainsaws yet available for other Poulan made products.

Mean while, back at the ranch. Gonna try Jim's idea. Also I have a set of forceps that may do the job.
 
:idea: :idea:

If you have room, take a piece of wire, bend one end into an L than stick the stright end to the head of the adjustment screw with a little JB weld. Did that on log splitter I had. Now the anti pollution people will probably find me and want the $3000 fine!
 
Michael Beck"..........Never seen it mentioned on there that the tool is illegal. If so I guess the law was broken because I now own one.[/quote said:
I don't think the tool is illegal, other than Poulan not wanting it resold, due to the problems with maladjustment causing air pollution problems, which Poulan worries about the EPA coming back on them due to engine emissions.
 
I did not think it was illegal since the government would be collecting taxes when one was sold. Have read somewhere that eventually carbs will be non-adjustable. I have never had much luck with these. On the husqvarna e-tech ( not sure about others) the muffler is what makes it epa compliant for now. Try what Jim suggested. Someone on the arborist site said they had done the same thing numerous times. Good luck.
 
The operator's manual included with the chainsaw states that Poulan guarantees the saw to meet EPA regulations for 50 operation hours.

I'm in the process of contacting one of the firms that sells the tool. I need two, one for each saw, since I'm working on my brother's and my nephew's. I'll put the tool in the case with each saw when I return the saws.

Just my opinion. This has got to be one of the dumber EPA rules. I own a bunch of 2 cycle engines. Not often, but every once in a while the carburetors need to be adjusted to get the engines running properly.
 
I did as the answerarmy suggested and looked at epa.gov. If their really is such a regulaton, they could have been more specific in where to find it. I could only find two regulations that seemed to relate in any fashion to this question.
You may not knowingly manufacture, sell, offer to sell, or install, any part that bypasses, impairs, defeats, or disables the control of emissions of any regulated pollutant, except as explicitly allowed by the standard-setting part. We may assess a civil penalty up to $3,750 for each part in violation.
Note that it restricts sale of parts that throw a machine out of compliance. It says nothing about tools that could cause problems if in the wrong hands.

Also, except as specifically provided by regulation, you are prohibited from directly or indirectly communicating to the ultimate purchaser or a later purchaser that the emission-related warranty is valid only if the owner has service performed at authorized facilities or only if the owner uses authorized parts, components, or systems.
I found another site that says anyone that can order parts from Poulan can order the tool. Who knows. IF they are restricting sale of the tool, it is probably their way of pushing customers into their own "authorized facilities" without directly violating the above regulation.

The bottom line, it appears that they may be simply using the EPA as an excuse for something that is their own choice.
 
Boss Hog":840uuqy0 said:
I think Boss Hog gets a commission for every time he mentions Stihl products.

I have two each Stihl chan saws. Used both today. One is about 20 years old and the youngest close to 15 years old.

The saga. I got one of the Poulan chainsaws running without any big problems. The second one I got running once. It was running very lean and hot. Shut it off, then it wouldn't start. Cleaned the carburetor, changed the plug, etc.. Engine cranked over, excellent compression, spark. Still no start. This morning fuel up the saw and went out side to try and start it again. Locked up tight. Dumped the fuel back into the gas can. Figgled with it checking the crankshaft rotation. Still locked up. Banged the front of the saw down at an angle. Saw freed up.

Complete tear down time. And probably pitch in the trash.

Moral is to purchase quality products. Cheap frequently turns out to be very expensive.
 
Back
Top