Joining ethernet cables

Paul_NJ

501 Club
Here's an off-the-wall question that I hope someone can answer. I'm running a cable from an internet server to a downstairs computer. I'm using Cat-5e cable to run from the router, thru the wall down into an outlet box (#2) downstairs in the house. The cable terminates in an ethernet socket, the type (RJ-45) where you push the 8 wires down into channels on the back of the socket.

I'd also like to have another ethernet outlet (#3) in an adjoining room where I can temporarily plug in laptop when I'm sitting next to the wood burning fireplace. A couple years ago when I had the wall open to install library cabinets, I had run another Cat-5e cable from that same downstairs outlet box (#2), through the wall and ceiling to a third room's own ethernet outlet (#3). I'd like to now connect that cable in the #2 box. I tried doing so by "punching down" the 8 wires of that cable on top of the ones already inserted into the RJ-45 plug, but the #3 outlet is dead. I've done this successfully with phone lines, but apparently it doesn't work with ethernet.

Can anyone give me a solution? Basically I want to daisy-chain from one room to the next without having to make two home runs back to the router.
 
Paul,
I did something similar several years ago and it worked. It may have been exactly the same, but has been too long for me to remimber the details. Seems like the main problem is it gets horribly crowded with 16 conductors in that small space. Maybe you just ended up with a bad connection.
 
Jim

Thanks for your response. At least now I know it should work. I'll try again, stripping the cable sheath back further. Perhaps the conductors will lie flatter.

Stuff like this can make you scream!!
 
I agree with Jim. I think they should work. It has been a dozen years since I ran cable and I pretty much forgot all that.

Just a thought. Since you run from a router, how old is your laptop? Just about anything less than 4 years old has built in wireless. Won't that make a connection to your router?
 
Barnyard,

A buddy of mine gave me an ethernet card to install in an old IBM Thinkpad 385 I seldom use anymore. It's not wireless, and doesn't even have a USB port. I just began using it on those cold Winter nights to reply to email, etc in the room with a fireplace, and a wired but not tied in ethernet outlet. It's slow, but good enough for that occasional purpose. I've been rolling out a 25 foot ethernet patch cord between rooms each night, but that's cumbersome. If I could just activate that outlet I'd have it made.

Paul
 
Paul,

If I was in your situation, I think I'd go wireless for any additional connections. Then you're not limited to being near the outlet. You can typically use your laptop anywhere in the house. Even outside if within range.
 
Whether or not that will work depends on how long the tun is, if the extra ends are very long they will either not work, or will be slow. Punch downs are not intended for more than one wire under each one, and frequently they do not make a good contact that way. Try using a pair of needle nose pliers to squeeze the sides of each punch down tighter. Of course, you cannot expect it to work if both computers are connected at the same time on the 2 added pigtails.
 
Something like this would be a good inexpensive solution too. I've got a couple of these 4 port hubs and have had no trouble with them at all. Simple to setup and your can use both PC's at the same time if you want.
An ebay search using " netgear 4 port dual hub " turned up several. Edited to add dual to the search, look for the 10/100 dual speed hubs.

http://cgi.ebay.com/NETGEAR-4-Port-10-1 ... dZViewItem
 
Paul_NJ":1x5advzv said:
Here's an off-the-wall question that I hope someone can answer. I'm running a cable from an internet server to a downstairs computer. I'm using Cat-5e cable to run from the router, thru the wall down into an outlet box (#2) downstairs in the house. The cable terminates in an ethernet socket, the type (RJ-45) where you push the 8 wires down into channels on the back of the socket.

I'd also like to have another ethernet outlet (#3) in an adjoining room where I can temporarily plug in laptop when I'm sitting next to the wood burning fireplace. A couple years ago when I had the wall open to install library cabinets, I had run another Cat-5e cable from that same downstairs outlet box (#2), through the wall and ceiling to a third room's own ethernet outlet (#3). I'd like to now connect that cable in the #2 box. I tried doing so by "punching down" the 8 wires of that cable on top of the ones already inserted into the RJ-45 plug, but the #3 outlet is dead. I've done this successfully with phone lines, but apparently it doesn't work with ethernet.

Can anyone give me a solution? Basically I want to daisy-chain from one room to the next without having to make two home runs back to the router.

Paul:

Well, I build all of my own network solutions and the one thing I have learned is that Cat 5 and Twisted Pair are not alike.

You have to run individual feeds for each outlet box. You cannot share boxed or junctions. I have 16 live Cat 5 plugs all over the house, and each is on a separate feed. Primarily because each feed will connect to a separate computer and each computer must have their own unique IP addy. You cannot get this if you have Cat 5 in series. So Daisy Chains are just not viable for this kind of solution.

If you want to have more than one computer connected in the same room using a single ethernet cable, you will need to have a hub/router in the room and the Cat 5 cable must be connected to the hub.

Scotch locks or similar items apply only to twisted pair and not to cat5 cable.

So, if you to be able to use that other cat 5 cable, you will have to actually put in a new end terminal package and connect to that.

Been there, done that.. I have well over 500 feet of Cat 5 cable running to various rooms in the house. Oh.. I also use Wireless Access Points to link the laptops as well as the extra computers that have popped up and are using Wireless Adapters.
 
Rudi":229t3gzd said:
Paul_NJ":229t3gzd said:
Here's an off-the-wall question that I hope someone can answer. I'm running a cable from an internet server to a downstairs computer. I'm using Cat-5e cable to run from the router, thru the wall down into an outlet box (#2) downstairs in the house. The cable terminates in an ethernet socket, the type (RJ-45) where you push the 8 wires down into channels on the back of the socket.

I'd also like to have another ethernet outlet (#3) in an adjoining room where I can temporarily plug in laptop when I'm sitting next to the wood burning fireplace. A couple years ago when I had the wall open to install library cabinets, I had run another Cat-5e cable from that same downstairs outlet box (#2), through the wall and ceiling to a third room's own ethernet outlet (#3). I'd like to now connect that cable in the #2 box. I tried doing so by "punching down" the 8 wires of that cable on top of the ones already inserted into the RJ-45 plug, but the #3 outlet is dead. I've done this successfully with phone lines, but apparently it doesn't work with ethernet.

Can anyone give me a solution? Basically I want to daisy-chain from one room to the next without having to make two home runs back to the router.

Paul:

Well, I build all of my own network solutions and the one thing I have learned is that Cat 5 and Twisted Pair are not alike.

You have to run individual feeds for each outlet box. You cannot share boxed or junctions. I have 16 live Cat 5 plugs all over the house, and each is on a separate feed. Primarily because each feed will connect to a separate computer and each computer must have their own unique IP addy. You cannot get this if you have Cat 5 in series. So Daisy Chains are just not viable for this kind of solution.

If you want to have more than one computer connected in the same room using a single ethernet cable, you will need to have a hub/router in the room and the Cat 5 cable must be connected to the hub.

Scotch locks or similar items apply only to twisted pair and not to cat5 cable.

So, if you to be able to use that other cat 5 cable, you will have to actually put in a new end terminal package and connect to that.

Been there, done that.. I have well over 500 feet of Cat 5 cable running to various rooms in the house. Oh.. I also use Wireless Access Points to link the laptops as well as the extra computers that have popped up and are using Wireless Adapters.


Thank you Rudi for clearing this up. I was so stubbornly convinced I was simply getting a poor connection where I joined the cable wires I went and soldered each color wire together with a pigtail to the RJ45 receptical. And the ethernet still wouldn't connect! The result, I suppose of trying to apply electrical knowledge to an electronic problem.
 
Paul - I'll let you in on a little secret. Only 4 wires on the 8 wire cable are used to send/receive data. The other 4 are ground wires to reduce cross talk on the cable. It is possible to have two connections on that wire, but you'll need to do some creative wiring and crimping.

http://www.delmar.edu/Courses/ITNW2313/ethernet.htm

http://yoda.uvi.edu/InfoTech/rj45.htm

The second links pictures are a little easier to follow.

Now the warning, your signal reliability will drop on both connections. If you don't use both at the same time, you might not notice it, but any noise on the line will only get worse. Also, please remember that you have to this hack on both end of the cable.

Of course, the better solution is just to run another wire. :D
 
Paul, I'm now doing network installation and configuration for the company again, and just so happens I make the Cat-5 cables on a regular basis.

I just finished making/installing multiple lines for another new lab network this month, and used up over 8000' of Cat-5E cable.

I have some cable left over, most of the lengths are less than 100' so they aren't much use at that length, so if you want to tell me what length you need, I'd be happy to make up the cable you need and get it to you.

I have all the tools & connectors to make the cables, and I can normally whip out a cable in less that 15 minutes, so it's no bother.

Let me know, the offer is there.......MD
 
Mike

Thank you for the kind offer. For now I don't plan to run more cables. A friend gave me a spare wireless card for my laptop, and that may resolve the entire situation.

Paul
 
Back
Top