John Deere 60 repair

Started installing the valves in the head and noticed some wear in a couple pairs of keepers. Need to get some new or good used one's which I will talk over with my cousin. Cleaned up the head gasket surface on the block and ran the rocker shaft parts thru the solvent tank and sonic cleaner.

100_5039-m.jpg100_5046-m.jpg100_5047-m.jpg
 
Drilled out a broken bolt for the crankcase cover and the used keepers arrived today. I ran them through the sonic cleaner so they are ready to install.

100_5048-m.jpg100_5049-m.jpg100_5050-m.jpg100_5080-m.jpg100_5087-m.jpg
 
Gary Dotson":1rt9n95y said:
That must be the optional 5 valve motor!
:lol: Yes, extremely rare. My thinking was to get some extra's since they are used and chose the best one's. They all look to be in good condition and this will give me spares if I need them in the future.
 
Assembled the rockershaft yesterday. Installed the valves, and installed the head today with my brothers help.

100_5088-m.jpg100_5093-m.jpg100_5094-m.jpg100_5097-m.jpg100_5100-m.jpg100_5101-m.jpg
 
ricky racer":2c4k3scw said:
It looks like the 60 is still using the lead washers under the head bolts...
Yes, it does use lead washers. By the time your done torquing the nuts, most of the lead is squeezed out.
 
cjet69":2dsckwsv said:
ricky racer":2dsckwsv said:
It looks like the 60 is still using the lead washers under the head bolts...
Yes, it does use lead washers. By the time your done torquing the nuts, most of the lead is squeezed out.
Yep, that sounds about right. :lol:
 
Started the repair on the radiator tanks. The flange area's had some rust eat into the gasket surface so I filled it in with Devcon plastic steel. I then placed it on a piece of plexiglass with wax paper on it to try to keep it as smooth as possible. Looks like it worked pretty good. This stuff gets really hard so I'm not sure if I can sand, file, or have to mill it.

100_5121-m.jpg100_5125-m.jpg100_5126-m.jpg100_5127-m.jpg100_5128-m.jpg100_5129-m.jpg
 
I was able to use one of my air sanders with some 80 grit paper to knock down the Devcon filler. I finished it up with some Emory paper on a flat file. There are a couple small voids still, but the sealer will take care of that when I assemble it. This will give me a nice flat flange surface to get a good seal on now.

100_5135-m.jpg100_5136-m.jpg100_5138-m.jpg
 
Prepped the top of the crankcase and shot some epoxy primer on it. I plan on shooting green on it and the radiator parts tomorrow and then I should be able to start bolting everything back on the tractor.

100_5152-m.jpg100_5153-m.jpg100_5154-m.jpg
 
I almost forgot about this water outlet that has the temp sensor in it. The sensor was stuck so I set back on the shifter to deal with later. Managed to get the sensor pulled and got it cleaned up. Also some pics of the old and new tires. I now have some front wheels to clean up and paint.

100_5169-m.jpg100_5168-m.jpg100_5167-m.jpg100_5166-m.jpg100_5163-m.jpg
 
That sensor plug and the radiator drain plug were absolute nightmares on mine...I ended up drilling and gently chiseling retapping. I am enjoying following along a lot.
 
ajhbike":307ul32w said:
That sensor plug and the radiator drain plug were absolute nightmares on mine...I ended up drilling and gently chiseling retapping. I am enjoying following along a lot.

The temp gage still works so I didn't want to destroy it just trying to get it apart. I used a propane torch on the reducer bushing and finally got it to break free without overheating it. I got about 1/4 turn and then it would get really tight again but with some ATF/Acetone mix sprayed on it from both sides it loosened up so I could pull the sensor out.
 
Pulled the front wheels, demounted the tires, and fired up the big sandblaster. One wheel was in good condition but the other had a fair amount of rust on the inside. Its a little thin around the valve stem hole so I will probably do a little welding and grinding to get rid of the sharp edge.

GOPR3638-m.jpgGOPR3639-m.jpgGOPR3647-m.jpgGOPR3648-m.jpg
 
Epoxy primed the front wheels. Sprayed green on the water outlet housing, governor housing cover, and the crankcase cover.

100_5173-m.jpg100_5180-m.jpg100_5181-m.jpg100_5183-m.jpg
 
Back
Top