John Deere 60 repair

ricky racer":3pzdqjoo said:
Looks good. Have you measured the bores yet? It looks like there's a fairly good gap between the pistons and the cylinder walls...
The bores look really good with no ridge at the top of the bore. Got to looking it over and found the pistons are aluminum with .125 stamped in them. Must have been just rebuilt just before my dad and uncle brought it home. It didn't get very many hours put on it since then either.

100_4786-m.JPG100_4787-m.JPG
 
Do you have access to valve seat grinding gear or Nuway valve seat cutters? I wouldn’t be able to resist giving it a good valve job, at this point.
 
touch up the valves while you have the chance! lol! even with low hours,---sitting is death on heads! I would re-grind valves and seats,---- wont take much but then your starting with fresh seating and a better running motor!
 
Gary Dotson":ie7hn1yf said:
Do you have access to valve seat grinding gear or Nuway valve seat cutters? I wouldn’t be able to resist giving it a good valve job, at this point.

SONNY":ie7hn1yf said:
touch up the valves while you have the chance! lol! even with low hours,---sitting is death on heads! I would re-grind valves and seats,---- wont take much but then your starting with fresh seating and a better running motor!

We have a valve seat grinder and a valve refacer machine. I checked our inventory and I needed to get some larger pilots and stones. Got those ordered and they should be here in the next day or 2. We also picked up a Sioux 645L valve refacer last year that needed some TLC. My dad and brother spent some time on it over the weekend getting the chuck loosened up and a general cleaning. We are approaching test time for it, just waiting on the cutting oil that is also in the order.

100_4788-M.JPG100_4790-M.JPG100_4791-m.JPG100_4793-m.JPG100_4794-m.JPG100_4795-m.JPG
 
My brother spent the weekend doing some more cleaning on the Valve machine. Its looking pretty good now. Got the coolant/grinding oil tank cleaned and flushed with some ATF. Drained the ATF and poured in the grinding oil. Did a test grind on a couple of old valves. The first cuts weren't smooth, kind of a chattery look. Dressed the stone and that straightened it up. The only thing we need now is a chamfering attachment. Some pics from when we first brought it home to camp are how it looks now.

GOPR2128-m.JPGGOPR2130-m.JPGGOPR2132-m.JPGGOPR2133-m.JPGGOPR3527-m.JPG
 
The Sioux was a good valve grinder, mine is the Black and Decker, very comparable. I also have the Black and Decker seat grinder but much prefer my Nuway seat cutters. I really envy the high end shops with the Serdi machines.
 
Gary Dotson":13sz1uyv said:
The Sioux was a good valve grinder, mine is the Black and Decker, very comparable. I also have the Black and Decker seat grinder but much prefer my Nuway seat cutters. I really envy the high end shops with the Serdi machines.

The Nuway's are nice. I used some on a couple different heads when my dad was an automotive instructor at a Community College. With the variety of different valve sizes that we do it would be cost prohibitive to go that route for us. We have a Sioux seat grinder that we use that dad has had a long time. We also got a Black and Decker seat grinder at the same time as the Sioux valve grinder. Both were free by the way. The next thing I would like to find Is a setup for installing hardened seat rings. We have several tractor heads that need new seats.
 
Yes, they’re pretty pricey if you have to buy a lot of different cutters. I stalked EBay till I found a used kit with 8-10 cutters. I haven’t needed additional cutters but have had to make a couple custom pilots.
 
After receiving my order of stones for the valve seat grinder, I found the thread insert isn't long enough to turn the stones around on the mandrel. Normally I would turn the stones and cut a different angle on the other side of the stone for a top or bottom cut of a 3-angle valve grind. I ordered 2 more stones so I should be good to go now. My cousin dropped off a gasket kit and I still need to do a final cleanup and measure to see if we need just a valve or a guide also.

100_4801-m.JPG100_4803-m.JPG100_4804-m.JPG100_4805-m.JPG100_4820-m.JPG
 
We got our chamfering attachment for the valve grinder which is one of the first steps you need to perform before grinding the valve face. Still waiting for a new exhaust valve to arrive but got started on the others. My brother came over last weekend and wanted to try out "the new to us" valve grinding machine. He faced and chamfered the stems and then chucked them up for the grind. The machine works well and with great results. We then moved on to refacing the rockers. The rockers look like they had been ground before and the face wasn't square. We were able to get them cleaned up good enough to work correctly.

100_4832-m.jpg100_4843-m.jpg100_4857-m.jpg100_4858-m.jpg100_4868-m.jpg
 
My cousin dropped off a new exhaust valve and a carb kit. Its been really cold in the shop (38°F) with our recent weather so I haven't been doing much on this project. The temp will still be cool overnight but in the mid 40's during the day so I should be able to warm the shop up enough to get some work done this weekend. Today I need to cut some wood (dead dry Cedar) for shop heat and tomorrow will be cleaning the cattle feedlot.
 
cjet69":xbp895y1 said:
My cousin dropped off a new exhaust valve and a carb kit. Its been really cold in the shop (38°F) with our recent weather so I haven't been doing much on this project. The temp will still be cool overnight but in the mid 40's during the day so I should be able to warm the shop up enough to get some work done this weekend. Today I need to cut some wood (dead dry Cedar) for shop heat and tomorrow will be cleaning the cattle feedlot.
:thumbsup:
 
Finished sandblasting the head yesterday and just sprayed some epoxy primer on the head and governor housing.

100_4895-m.jpg100_4896-m.jpg100_4897-m.jpg100_4904-m.jpg100_4906-m.jpg
 

Attachments

  • 100_4905-m.jpg
    100_4905-m.jpg
    226.2 KB · Views: 18,663
Wire wheeled the fan shaft and treated it with Ospho. I'll get it primed tomorrow. When the primer is cured I'll do a final cleaning on the governor and fan shaft and then its ready to assemble.

100_4908-m.jpg100_4913-m.jpg
 
Primed the fan shaft and applied some more Ospho to the radiator parts. I think I have the rust killed this time.

100_4914-m.jpg100_4915-m.jpg100_4917-m.jpg
 
It was another fairly nice day with 54°F temps so I set up outside and primed the radiator parts.

100_4920-m.jpg100_4921-m.jpg100_4922-m.jpg100_4923-m.jpg
 
Back
Top