In The Barn

[Rudi]

This chapter contains topics relating to working on our Cubs. From simple maintenance to repair and restoration of our Cubs and Cub Implements including modifications.

• In The Barn
  
  • All About Cub Maintenance, Repair and Restoration
    1. How To Find Parts For Your Antique Cub
    1. Engine
       
    2. How To Inspect & Repair A Governor
    3. How To Lap Small Components
    4. How To Lap Valves
    5. How To Adjust Valves - Method #1
    6. How To Adjust Valves - Method #2
    7. How To Install A Head Gasket - Method #1
    8. How To Properly Remove A Crank Pulley - Method #1
    9. How To Properly Remove A Crank Pulley - Method #2
    10. How To Repair A Cracked Block - Method #1
    11. How To Repair A Cracked Block - Method #2
    12. How To Remove A Seized Exhaust Pipe From The Manifold
    1. DriveTrain
       
    2. How To Repair A Tranny With Broken Shifter Forks
    3. How To Adjust Clutch Fingers
    4. How To Rebuild Cub Final Drives & Brakes
    5. How To Rebuild A Cub Transmission
    6. How To Remove A Reluctant Pilot Bushing From The Crankshaft
    7. How To Repair And Re-Install the PTO Pilot Bushing
    8. How To Rebuild A PTO
    9. How To Repair A PTO Shifter Guide Plate
    10. How To Re-Install The Transmission Into The Torque Tube
    11. How To Helicoil A Rear Final Implement Mounting Hole
    12. How To Install A Front Tire Using H L Chauvin's Tips
    13. How To Easily Install Wheel Weights
    1. Electrical
       
    2. How To Buy A Proper Battery For Your Cub
    3. How To Understand And Test Batteries Safely
    4. How To TIme A Magneto - Method #1
    5. How To Time A Magneto - Method #2
    6. How To Perform A Tractor Electrics and Voltage Drop Test
    7. How To Test An Ignition Coil With A DVOM
    8. How To Understand And Test Ignition System Condensers
    9. How To Understand Firing Order
    10. How To Polarize Your Generator
    11. How To Oil The Generator With The Hood On
    12. How To Polarize Your Generator With The Hood On
    13. How To Test Points
    14. How To Set Points
    15. How To Replace Points etc. In A Distributor
    16. How To Retrofit a 4411 Sealed Beam into a Pancake Style Housing
    17. How To Repair A Pancake Style Headlight Housing
    18. How To Repair Pancake Style Housings with a Custom Nylon Contact
    19. How To Add A Bullet Light to a Tear Drop Light Housing
    20. How To Make A New Style Voltmeter Guage Resemble An Original IH Gauge
    21. How To Add A 12 Volt GM Single Wire Alternator
    1. Fuel
       
    2. How To Install A Fuel Tank Strainer
    3. How To Install an In-Line Filter in 5/16" Steel Gas Line
    4. How To Upgrade A Cub Fuel System
    5. How To Straighten IH Updraft Carburetor Tops
    1. Cooling
       
    2. How To Test A Radiator
    3. How To Check for A Leaky Radiator
    1. Touch Control
       
    2. How To Rebuild A Touch Control
    3. How To Rebuild A Touch Control Pump
    4. How To Rebuild A Touch Control Reservoir IH Part # 360 719 R1
    5. How To Repair Touch Control Stops
    1. Superstructure
       
    2. How To Remove Dents In The Gas Tank
    3. How to Replace Broken Dogleg Bolster Screws
    4. How To Repair A Worn Throttle Quadrant - Method #1
    5. How To Repair/Rebuild A Worn Throttle Quadrant - Method #2
    6. How To Keep Choke and Starter Rods Looking New
    7. How To Remove A Cub Floor Pan
    8. How To Restore A Manifold
    9. How To Restore or Refinish An Underslung Exhaust Pipe
    10. How To Fit A Mesh Grille
    11. How To Mount A Deluxe Seat on a Pan Seat Spring Assembly
    12. How To ReFurbish A Steering Wheel
    13. How To Apply Decals To Your Cub
    14. How To Safely Remove The Serial Number Plate
    15. How To Re-Use That Old Serial Number Plate
    16. How To Refurbish Aluminum Emblems
  
  
  • All About Maintaining and Repairing Your Cub's Implements
    
    1. Maintenance and Repair
       
    2. How To Change Blades On A Woods 42 Mower
    3. How To Restore Disk Hillers
    4. How To Remove Mott Mower Roller Bearings Part 1