Heating With Wood

Mr E.... all we have is the stove in our bottom living room. We don't even have it hooked up to a system to blow it around the house. Sure is hot downstairs but it does heat up the whole house. But of course I'm the lucky one with the bedroom the farthest from the stove... i freeze a lot. It does save on the electric bill though.
 
I started burning/heating with wood back in '79 thats one year after the blizzard of '78 that kind of scared me with small kids. We were lucky enough not to lose power for those days we were snowed in. The snow in the street was 5' to 6' deep plus the drifts. I had one drift go over the top of the ranch style house.

Later that spring it was time to go for a woodstove so we had a heat backup and for a saturdaynite so we could watch the fire. Then the offers of free wood came in so my wood burning became into heating the house 24/7 in the winter. Then when i lost my job i went into doing firewood full time.

Now when i installed my very first woodstove(russo) with the stainless steel chimney it all went pretty well and was easy to do. You have to make sure all your clearances are correct for the stove. But i put a sheetmetal guard 1" away from the wall and put the stove 18" away from the metal guard. I also put a guard up the wall behind the stove pipe too up to the ceiling just to besafe. You need to follow the stove manufacturers specs each woodstove is different.

I never had a chimney fire to this day. I clean the chimney every fall with the brushes. I also have two temperature gauges, one on the stove and another one on the stove pipe. This tells me when to adjust the damper on the stove so it gets to the right temperature so its burning up the creosote while its in the woodstove and not sending it up the stovepipe to the chimney. I run my woodstove between 350 to 400 degrees.The other temperature guage is 1/3rd of the way from the ceiling on the stove pipe. It tells me how much heat is going up the chimney so i'm not making creosote in the chimney. You adjust the damper on the stove pipe to keep the temperature between 250 to 325 degrees. One more thing about heating with a woodstove is once a day you need to heat the chimney to at least 400 degrees for a short time to melt the creosote that does form in it. I just open up the stove and stove pipe dampers till it gets to that temperature and then shut it down to regulate it to the normal temps. Using the two temperature gauges cuts down on the creosote and your wood consumption too plus your not over heating the woodstove or your chimney too. You watch the gauges and adjust it, its down to a science now once you learn how to do it.

Once your woodstove and chimney is up to temp you can also put in pine at this time too. The haet will burn up the creosote right in the stove before it leaves it. Just a little pine at a time, mix it up with the hard wood, again once its up to temp.

At the new place i put a temp woodstove (top loader) in the down stairs fireplace. I took out the damper in the fireplace and made my block off plate and put a damper on the stove pipe that connects the woodstove to the block off plate. I also put floor vents in all the rooms upstairs too. On the coldest nights my house is a cozy 72 degrees upstairs on the main floor. My woodstove heat moves by natural convection. It goes up in the living room, kitchen, the 1st bedroom and bathroom and goes down the hallway into the two back bedrooms and returns down stairs back to the woodstove(natural convection) it complete's the circle. The air moves so good the down stairs doesn't get too hot. I'm thinking of going with larger floor vents to see how much hotter i can get the upstairs then i can control how much the heat is flowing by adjusting the floor vents. Heating this was is still new to me but its working good so far. I think i used about 150 gallons of oil last winter. This year i expect to use less oil. I only used 4 cords of firewood too. While the new place is mainly brick outside its very well insulated but it also has very large anderson windows so thats my only heat loss so i'm not doing that bad.

My two neighbors are spending $3,500 to $4,000 per heating season this was before the price increase on oil. Its over $1,000 everytime the oil man comes to deliver.
Now they expect to hit $5,000 to $6,000 for oil to heat there house. If you don't want to do firewood even a pellet stove can make a big difference in your heating bill.

To setup for cutting and burning wood is costly but when the heating oil is estimated at going to $4 or $5 a gallon. A cord of firewood here just hit $300.

Now a guy selling firewood shows up with a 1 ton truck with two cords i just laugh at him. Your really only getting 1 1/2 cords if your lucky. My point is becareful who you buy wood from too and make sure your getting a full cord thats what your paying for.

A cord of firewood is 4' x 4' square and 8' long stacked. Its actually 128 cubic feet of space.

When i was selling firewood I stacked it in my truck so your getting a full cord of wood measured before I delivered it.

I have only purchased firewood 3 times since 78.Out of the 3, 2 of them sold me 1 1/2 cords for 2 cords. I only found one guy who gave me 1 cord exactly everytime.

You can also burn pallets/skids too besides firewood. I was burning pallets from late September to mid december depending how cold it was. There's a time when one fire will heat the house. When it gets colder i would gp to the big wood. You can burn pallets in the early fall and late spring to conserve the firewood too.

I let my firewood season at least 1 to 2 years before i burn it. I have seen some burn the firewood seasoned only 4 months. My point is make sure you clean your chimney at least twice during the heating season if your wood isn't seasoned that long.

Put those temp gauges on your woodstove and on your stove pipe too they also help out a lot too.

If you have a woodlot thats at least 10 acres of hard woods it will outlast your lifetime and more by selective harvesting. By the time you start on one end of your woodlot and cut to the other end the first end you cut will be ready to cut again. You will never run out of wood to burn.

Another source of firewood is blowdowns too. That old pink colored punk wood oak(no bark left) sure burns longer, too bad its passed up by many wood cutters because it isn't pretty. I burned anything that was still hard wether its standing or on the ground.

When using a chainsaw always start the day with a sharp chain. Always stand to the left of the chainsaw, never stand right behind the centerline of the bar & chain. If the chain ever snaps it may go straight back at you. You never know whats inside the wood too. I have hit steel pipes and screwed in eye bolts that the wood grew over. On the splitter when you see the purple color inside the wood there's steel inside it so becareful with the log splitter too when the knife hits that steel too. You need to be on your game 24/7 when doing firewood know the hazards and what to watch out for. Its not so easy as running a chainsaw.

Coal mining is the number 1 hazard
Logging is #2.........becareful, plan your work ahead of time, plan your escape route before you fell trees. Cut an escape route before fellin trees if you have too. There's no second chance when your fellin....always go on a 45 degree angle from the tree when fellin. Never walk behind it because it can shatter backwards. Make sure you use plastic wedges when fellin large diameter trees too. Put them in right after the bar and chain disappear into the treee and there's room for the plastic wedges. Why plastic? So you can go back in and cut again without dulling your chain. The wedges are so the tree won't close up on the saw on big trees. Never cut on a windy day the swaying trees are unpredictable(heavy wind).

Besafe and enjoy the outdoors too.

I shut my saw off one day after fellin some trees during the light snow and i sat on one of the stumps and could hear the snow hit the ground. No one has a better workplace than i had.
 
I promised some pics and I finally got around to loading em up. Pictures aren't going to be the best, cause the available room to take pics is somewhat cramped and the angles just are not conducive to quality pics, but hopefully one can get the gist of what the pics are trying to show.

Here is a pic of the front of my Scotty DB II 70,000 BTU Wood Furnace.

ScottyDB2-04.jpg


Against the wall you can see the 5" Make Up Vent that is used to provide cold crisp fresh air to my firebox in the winter. Without a makeup vent such as this, the fire will not burn as well, as it is trying to draw air from inside the house. It is difficult and the interior air is warm and tends not to have as much oxygen to fuel the fire. The makeup vent forestalls this problem. Since we installed the makeup vent, our heating costs have fallen drastically.. even though our cost are already dirt cheap. The next pic below is a frontal shot of the Scotty and the Electric Backup furnace. The two furnaces work in concert.. the electric furnace provides the cold air supply plenum and blowers. The wood furnace has the hot air plenum which is plumbed into the forced air ductwork.

ScottyDB2-02.jpg


The following pics are of my Wood Room and Kindling Box. Now the wood room is 12x14x10 foot high. This provides enough room for 10.5 cords of wood. In this case a long cord is the actual 16" x 48" x 144" which equals 48"x48"x96" or 128 cubic feet. My wood box is exactly 4 foot. This will account for 1.0 cords of wood as it is 48x48x96 inches high inside. So with my wood box and piled wood, accounting for the last 2 square foot of floor space which I very seldom fill up, I can put exactly 9 cords of 16" and 1 cord of kindling in my wood room for a total of 10 cords. If I need more, I can pile another foot on top of my existing 8 foot and achieve probably 2 more cords total.

Kindling Box
WoodBox-02.jpg


The kindling box is usually filled with mill ends and other small pieces from my wood shop, or as in this year's case.. off cuts from the pole barn project. Waste not, want not :!: :idea: :wink: :lol:

WoodRoom-04.jpg


WoodRoom-01.jpg


WoodRoom-02.jpg


The bottom of the window is just above the top of the insulated stud wall. The stud wall is exactly 8 foot high. As you can see, there is lots of room for wood.
 
Moving the wood;
I put in a wood shoot so i can just slide the wood into the basement. My wood is covered outside and kept dry all summer. I put over a 1/4 cord in the basement and fill the wood shoot up plus i keep the trailer on my cub cadet filled(1/4 cord+) and keep it near the basement enterance.

This year i'm going to keep 4 cords near the basement enterance so i have less to move in the snow.

You have to make it really easy to do when your burning wood. I been thinking of palletizing my firewood and moving it with the 3pt hitch on my int154 cub. Then its easier to bring it close to the house/shoot. The less handling the better.
 
In Franklin i use wood. The original was a 2 barrel stove Bev and I used living in the basement as we framed the house. Later when the was closed in we let the heat circulate by convection from the basement. By mid December it was -20 but we were comfortable even with no insulation in the walls or ceiling. Sure did run a bunch of woo through that thing. We had to replace the barrel's the following year. I replaced that with a Thermo Control wood stove. There are 3 loops of 3/4 inch black pipe in the interior of the fire box. As temporary heat I ran them to a manifold and ram 1" pipe to 3 convectors on an interior wall and 6 old radiators in a first floor hall. With an aqua stat controlling a circulator heat is pushed to the first floor as well as some by convection up the cellar stairs. I shut off the electricity to the circulator with an outside temp of -10F to insure that I would not create steam and dangerous pressure in case of an electric failure. It worked well the gauge read over 200 degrees but never exceeded 212 degrees. A four hour trial satisfied me that it was safe pushing the fire with no circulator. I was able to cool it down by restricting the input air draft. I use 22 gauge welded seam stove pipe through a 1/4 inch steel plate where it passes through the floor. It then goes through a "Heatolator" where a fan controlled by a thermostat steals heat from the flue gasses. After that it L's into tripple wall stainless steel flue pipe and out of the roof. The chimney ends about 3 feet above the highest point of the chimney.
There is a cap on the bottom of the T where the stove pipe L's in to the chimney. I use that as an inspection port for the chimney. There has never been a creosote deposit in the 20 years or so we used this system because we do the small hot fire trick daily in cold weather or weekly in the fall and spring. I burn everything, paper, cardboard, construction wood scraps, pallets (good kindling), pine, poplar, various oaks, maple, cherry, hop hornbeam, iron wood, beech, white brown and yellow birch as well as some I don't know the name.
In some of the pictures I have posted from time to time you will see wood piles on old electric pole cross arms set on concrete blocks to keep off the ground. The stacks are 8 feet long, four or 5 feet high with 24 inch pieces. The stove will take 30 inch pieces but Bev found that size a bit much for her so it is 24 inch. The stacks are covered with old swimming pool liners. I cut 10 by 10 pieces and sandwich the sides between a 2/4 and a 3inch firing strip leaving a 2 foot overhang at each end. The 2/4 and firing strip sandwich weigh down the sides to hold them in place during high winds. This keeps snow and rain off the wood. The latest covers use pool cover as well as the liner. The cover with the fabric next to the logs to prevent rips in the liners.
I use the bucket on the 1050 to bring wood in the house and generally have a cord and a half to 2 in the basement. The 20 acres of woods still need a lot more thinning and clearing up. I am ony 76 but will not live long enough to burn all that up.
Oh yes because this is a seasonal home the water in the pipes is 50/50 Prestone. I have read that you should not use automotive antifreeze in a heating system. By the time I read this it was too late for it was fact accomplished. I later learned probition was, in case of a leak Automotive Anti Freeze can kill animals or polute the ground. The antifreeze for heating systems is nontoxic.
Take extra chains when cutting fire wood. The minute a chain stops throwing big chips I change it. I have an electric chain sharpener which will adjust to just take a whisper off and restore a chain to new. When a chain is dull much more metal must be removed to sharpen. The splitter helps as the buzz saw used to and will again.
Enough long windedness.
 
I sharpen my saw chain before i go cutting so there razor sharp all the time most of the time one pass with a file and guide does it. They last while cutting if there isn't much dirt in the tree bark.

I use chisel chain for clean wood(fellen trees and bucking them up) and semi chisel for wood with dirt in it. (at the landings or at the saw mill) The semi chisel is less forgiving and lasts longer in dirty wood.

I use a file guide that keeps the file at the top of the teeth so it sharpens the very top of the tooth. I'll get a site were there at and post it so you can see what i'm talking about. The guide has two different degreed angles for chisel and semi chisel saw chain.

go to; http://www.oregonchain.com/accessories.htm


I also sharpen my 3/8 chisel saw chain with a 1/4" file too and then use the 7/32" file to make some chip clearance in the center. The chain sharpened this way cuts faster. I started doing this to speed cut at the fairs in competion and then used it in the woods.
 
Don't forget when splitting wood hit the log at the 12 oclock position so you don't miss it and hit your foot. Don't ask me how i know. Do not try this with sneakers, wear good quality boots......

Burning wood isn't so cheap anymore. I just paid $100 for hydraulic oil for my log splitter. (12 gallons)

I'm also starting to think my bar oil and motor oil in a 55 gallon drums maybe cheaper too. Right now i buy motor oil on sale when i can the last deal was 2qts of motor oil for $3.

Of course paying for equipment is still better than paying for heating oil. Its $4.29 a gallon this season unless you pay for 500 gallons ahead of time at $3.99. I didn't burn 200 gallons last season and i plan on doing better this season too.

Stay warm burn wood!!!!!!
 
Hey BigBill, have you ever tried square ground chain. Me and Earl where introduced to it last year at a GTG. We both switched over and I personally don't use any round ground chain at all now. Amazing difference in the speed of the cut. I run it in full comp for all my cutting including quartering up the big ones with the grain.
 
WKPoor":2fuvu32e said:
Hey BigBill, have you ever tried square ground chain. Me and Earl where introduced to it last year at a GTG. We both switched over and I personally don't use any round ground chain at all now. Amazing difference in the speed of the cut. I run it in full comp for all my cutting including quartering up the big ones with the grain.

Square ground saw chain (Chisel chain) I have used it for many years until lately. Chisel saw chain is great in clean wood(standing timber) it cuts very fast. Right now i'm cutting trees that been laying on the ground that were skidded at some point so some are full of dirt in spots this is were semi chisel or chipper chain / round ground is less forgiving in dirt it holds the sharpness longer with dirt over chisel chain which loses its edge right away when the contact with dirt is made. When i go back to standing timber its chisel chain for sure.

Now lets talk about sharpening your saw chain a little more.

3/8" saw chain;

I'm using a brand new 3/8 saw chain and after 5 or 6 sharpenings its not cutting as fast as it once did. The saw should be throwing out big square chips and its not. Plus its just not cutting its making saw dust. If you look from the side of the tooth the arc of the chip clearance is egg shaped towards the lower front. The chip clearance needs to be addressed. I take each too with just a 7/32" file and make 10 passes inside the tooth towards the bottom inside corner to clean it out to a larger radious. Once the inside lower tooth area has a rounded out spot I take a 1/4" file and sharpen the very top edge of the tooth that cuts. I run the file till the cutting edge is clean and sharp. Two or three passes will do it in most cases. Now i address the rakers these set the thickness of the cut of each tooth. While they make a gage for this i use my eye and experience to do this. I take a flat file and make 3 passes on each raker. The distance from the top of the tooth to the raker should be between .020 to .025". Remember to lower the rakers you must file to the outside of the bar. To do the right side rakers you file to the right side of the saw. To do the left side rakers you file to the lfet side of the saw. Now all my resharpenings are done with the file/guide until the chip clearance goes bad again. There's nothing like a well sharpened saw chain the saw will cut faster and easier too.

.325" saw chain;

Its the same process only the files are smaller. I use a 5/32" file to hog out the chip clearance and a 4.5mm file to sharpen the top cutting edge. The raker depth is only .020" max.

I sharpen both saw chain the sameway wether its semi chisel/chipper chain or chisel saw chain. They need to have lots of chip clearance. My chip clearance goes from the top of the cutting edge to the top of the chain links its a big radious. Its twice the chip clearance a new saw chain has. Just try it and you will see the difference.

I learned this way of doing at the local fairs competing with chainsaws. I wanted to have more chip clearance so it would cut faster. We were competing with pine(wood) timbers and i set my rakers at .060" on my 100cc saw and i did 8 cuts in 17 1/2 seconds and won the top of the class. Do not set your rakers more than the suggested amount by the saw chain manufacturer for normal wood cutting.
 
BigBill, Most of that was greek to me. All my round chain when I was using it was ground on a grinder I have. When I switched to square it take a special double bevel file or a special grinder that is very expensive. I know the square is less forgiving in dirty wood but I'm not having all that much trouble with and since I've learned to file it I can rather quickly recover a dull chain. I even make square out of brand new round on occasion.
Last April I won the 100+cc class with a barowed Stihl 880 Woods Ported
next class 100+ 2 cuts VERY FIRM 10x10

muffler

1. wkpoor 084 4.60
2. cut4fun 084 4.90
3. blsnelling 084 10.16
4. Al Smith 038mag 12.40
5. Al Smith mac125super scratch

I saw a piped cut that same cant in about 1.5sec per cut. Smooookin!
 
Back
Top