Electric Heat Question

I have to put in electric baseboard heat in my house. I have a 220 line run upstairs. I am wondering if anyone can help me decide what to get. I have never dealt with electric heat and these companies say they are the best in quality and price (ie hydrosil) but I am wary of buying anything these days. Any help is appreciated.
 
Electric heat is expensive...up here anyway. There are these mantels with an electric heating element in them that is safe and cost 4 cents an hour to run. The Amish were marketing them.
 
Chris is right. Electric baseboard heat, while being the cheapest system to buy, is without a doubt terribly expensive to operate. If you are going to install it you need to know the capacity of the wiring you have run upstairs. #12 wire is good for 20 amps and #10 wire will carry 30 amps. So, if you have a #12 gauge supply line the max wattage would be around 4400 watts. A #10 gauge supply line could handle about 6600 watts of heat.
If you are running that kind of electrical usage your bill will go out of sight.
 
I'm not familiar with hydrosil but it doesn't really matter. All resistance electric heaters are equally efficient... they all put out exactly 3413 BTU/KWH. Baseboard units, regardless of manufacturer, are the cheapest but poorest choice because of the radiant loss through the outside wall that can't be avoided in the normal installation. Your starting point should be an accurate heat loss calculation so you know exactly what to install, and operating cost calculation based on your actual local cost/KWH.

If your house is insulated to electric heating standards (ASHRAE) a very rough idea of your needs could be figured at 10 watts/sq. ft.

Those Amish units are really a sick joke. Their low operating cost is only because of their very low heat output... save your money. It would take a lot of them to heat any significant area. The only way to get more heat from electricity is with a heat pump.
 
We have been using a SunTwin heater for the last 4 years and love it. When temps are above 32 degree, the furnace never comes on and it helps slow the time it does kick on when it is colder. Safe, energy efficient and the nice wood case makes it look more like a piece of furniture than a space heater.
 
i'm not sure ,with the cost of oil and propane, electric is starting to look just a little bit better. you should take a look at your local utilities rate structure. here in southeast pa. there is a rh or residential heating rate. the way it works here is after you use 600 kw the rate drops to almost half. that doesn't make it nessesarily appealing. you really can't make an educated decision until you find out how the local humungus electric sets the rates. they have radiant baseboard heating that are oil filled and the heat dissipates much different then the hot element type also. i do think they are a better type. my two cents. i am a annuitant from the electric company :lol: :lol: :lol:
 
As most probably know, I am not a huge fan of fossil or electric heat. I like wood heat, but I also realize that it just is not a viable option for most people. So I think I am pretty fortunate and I don't have to worry about cost increases. I know others do, so I do try to pay attention and keep reasonably current on available systems. I used to have Propane as my backup system, now I have electric forced air as a backup, but we never use it. I have friends who have gone from heat to propane, to natural gas and wish they had never converted. I have neighbours who have electric and wish they never converted. Em's aunt and uncle have a heat pump which they like and they also have a HRVS system as part of their overall heating solution. Been hearing the pro's and con's for years. Without getting into specifics etc., I think that when it comes to efficient and financially viable options, I gotta agree with George, the only really viable electric system would be a heat pump or a HRVS setup.

RH rates are not a given or something that won't change, so if you make a decison to go to electric, don't make it based on rh rate differences cause that is not a guarantee. We have here in NB historically low Residential Heating rates.. first 900Kw are at about $0.08/kwh and after the first 900 it goes down to around $0.05/kwh. However, that appears to be a previous system. They just announced that NB Power would realign its Residential Heating rate to reflect other jurisdications similar to ours in the NE US and across Canada. Apparently it RH is now going to be an across the board $0.09/kwh with no reductions based on usage, so that will probably mean even higher utility bills for our electric heat neighbours.

Yup, I really like wood heat :!:

I really have no idea what to say to you about your dilemma, but I think a lot of research into year over year averages for your area over say a 10 or 20 year period would be useful to see what historically is actually viable for your area.
 
daddydip":1m5umaj6 said:
i'm not sure ,with the cost of oil and propane, electric is starting to look just a little bit better. you should take a look at your local utilities rate structure.
I have a kerosene fueled torpedo heater for the work shop. I also have a forced air electric furnace (which is another story). When the price of K-1 kerosene got somewhere towards $4 per gallon. I checked the rates and found it cheaper to switch on the furnace and forget the kerosene. I really should have docked the kerosene costs because of the need to provide ventilation when using it but didn't.

I don't use heat out there very much so I haven't run the numbers lately. It sure is nice to just throw a switch when I want heat and not end up smelling like kerosene smoke when I have been out there.
 
Back
Top