Air Compressor Suggestions

Harold R

501 Club
I finally got an air compressor that I feel will be adequate to run some tools in my shop. I had been using a direct drive Coleman Black Max 27 gallon, but it was barely able to run my die grinder or my impact wrench with out running constantly. And.....it was very noisy. My question is about some recommendations on setting up the air line exiting the tank. I believe it's a 1 inch NPT exit. I would like to have a ball valve shut-off, water separator/filter, and a regulator. I'm not going to plumb it all through the shop, just one line with a quick disconnect. Any hints or tips would be appreciate because I want to do this right, and not have to worry with it any more. Not sure it's necessary, but I will be bolting it to the floor.

2010-12-28%2014.47.31.jpg
 
Harold, mine is a little bigger than that, but the tank has a similar design. I came out of the side with a long enough nipple to give clearance for a ball valve handle then put a T on it. Both sides have quick couplers, with one side connecting to a short hose to use at the bench right beside the compressor, and the other side connects to a hose going to a 50 ft. air hose that allows access to the rest of the shop.
 
Not sure it's necessary, but I will be bolting it to the floor.

Looks nice Harold. A guy can never have enough air :D My Matco big 80 gal verticle tank compressor just sets on some rubber belting pads I cut out and it's never moved over the years. An option. I have a similar hookup like you want to install. I ended up buying a hose real that came with 120 feet of hose. The air pressure drop is quite abit. I have my tank pressure set only at 125 and I only get about 90 at the end of that 120 foot long hose. I also hooked up another shorter 25' hose if I need full pressure for the tough jobs with the impact. At Toledo Jeep, they ran 90psi through all their lines for controlled pressure for all the air tools.

Rick
 
Hi Harold

I have just about the same compressor you just got. I never bolted mine down its still on the pallet and has been for 10 years. One of these days I want to make a small room behind the garage to put it in. Its not real noisy but would be a lot quieter in a insulated room.

I will strongly suggest getting the ball valve for the tank drain. I still have the T handle drain and its a pain to open and close. Its a good idea to have a ball valve at the tank so if a airline break you can shut off the air. Also it keep the air from draining off if you are not using it for a while. I have found that having the water separator works better if it is away from the tank. As the air goes through the line it cools down and more water condenses out of it. My compressor is at the back of the garage and when I am painting I run a hose to a separator/regulator on the front wall. Its also nice to have full tank pressure outlet for using a impact gun.

Billy
 
I copied an idea from Bigdog. Mounted a 25' retractable reel (HF) in the center of the shop (ceiling). I can pull the hose to any corner and it's a lot more convenient than having to fight with coiling up a 50' hose from the compressor all the time. Mine was also left on the pallet, you'd have to convince me that it needs to be bolted to the floor.

Bob
 
Rick Prentice":3ms2flq6 said:
Not sure it's necessary, but I will be bolting it to the floor.

Looks nice Harold. A guy can never have enough air :D My Matco big 80 gal verticle tank compressor just sets on some rubber belting pads I cut out and it's never moved over the years. An option. I have a similar hookup like you want to install. I ended up buying a hose real that came with 120 feet of hose. The air pressure drop is quite abit. I have my tank pressure set only at 125 and I only get about 90 at the end of that 120 foot long hose. I also hooked up another shorter 25' hose if I need full pressure for the tough jobs with the impact. At Toledo Jeep, they ran 90psi through all their lines for controlled pressure for all the air tools.

Rick

Harold,
I elected to move my compressor out of the shop to try to get rid of some noise. I like it. Other than that, I am setup like Rick, except my hose reel only has 50' of hose on it.
 
[strikethrough][/strikethrough]

Remember to drain the water out of the tank ever week or two. A shut off is a must as well as a water seperator. As for mounting to the floor, mine has been sitting on the pallet it came on for 2 or 3 years, but i only have a dirt floor :lol:

Boss
 
Put it outside the shop, or, in a small,insulated room. Your ears will thank you. Cecil and I moved his, before the last cubfest, and the silence is great! Ed
 
This is something that my compressor service tech recommended to me years ago. He said to ensure that you supplied air comes from outside the building/ventilated area where it is not heated. Less condensation in the lines. He was right. I still drain my tank weekly/bi-weekly when I do not use it a lot and every couple days when I am using it a lot. I have all flex lines in my shop and I think it will be flex in the pole barn when I get to it. Right now the pole barn is fed off a secondary quick connect at the tee where the shut-off is. The retractable reel is a heck of a good idea if it is in the budget.... :D

If you decide to bolt the tank to the floor, do yourself a huge favour and use some dampeners between the floor and the compressor. You will be glad you did :roll: :wink: :!:
 
Rudi":2gmk4c43 said:
I have all flex lines in my shop and I think it will be flex in the pole barn when I get to it.

Rudi,
Please provide more detail on the flex lines you are using.
 
Harold,

If you intend on ever using your compressor to sandblast and/or paint, you might consider adding a desiccant dryer with replaceable desiccant. I bought one similar to that in the below link from McMaster-Carr. It cost about $105, but with -45degF dewpoint, you don't have to worry about moisture in your airlines anymore. The desiccant is replaceable, but you can also reheat it to regenerate the drying properties. The desiccant starts out blue and turns pink, when it is saturated. It is rated for over 7 hours at maximum flow. Granted is is a little pricey, but well worth it if you plan on painting or sandblasting.
http://images2.mcmaster.com/Contents/gfx/small/5163kp1s.png?ver=11536609
 
Just a little input on how we did our 60 Gallon IR . To dampen vibration noise down the line , we used a 1" hydraulic hose to go from the compressor outlet to the copper lines we used thruout the shop. Mounted the compressor to the floor using
( plastic type ) vibration isolators between the slab and compressor feet to reduce some vibration noise. We also mounted a hose reel next to the compressor and with a ball valve shutoff for the outside projects. :D
 
Boss Hog":3mfjoe2p said:
Remember to drain the water out of the tank ever week or two. A shut off is a must as well as a water seperator. As for mounting to the floor, mine has been sitting on the pallet it came on for 2 or 3 years, but i only have a dirt floor :lol: Boss
Mine is also still mounted to the shipping skid it came on after 4 years. The drain is a real pain to get to the way it is originally, so I extended mine out from under the tank and put a valve where I could reach it without laying on the floor and reaching under it.
 
Fantastic ideas Gentlemen. So many things I haven't thought of. I spent most of the day running the 220 service to the shop. So maybe tomorrow I'll get into the plumming. Thanks for the advice. I will be using it, for sure. 8) 8)
 
Jim:

I will see if I can find the name/stock # for this stuff. It has been a few years (about 20 I guess) since it was done and I have yet to have a leak or a blowout -- fingers are crossed and I knocked on wood (read skull) .. :lol: I will try to get it for you tomorrow when I go down to the shop.

EJ:

I did the same thing. It used to be real rough on my knees bending down on the concrete to reach around and under the tank to open the drain cock.
 
Well got myself a new toy to the Cub Cave. I got a U S General compreessor Model US56V from HF. 60 gal 5 HP 2 stage upright. Had Larry Gray wire it for me. I took Ricks advise on putting belting under the it to cushion the compressor. I put in the other garage. So far it is working great. I had a 20 gal. CH horz. under the work bench in the same room it would not keep up with a lot of things that I have added through the years. I'm goin to give it to my boys & hose an other equipment to put in their garage.

There's one thing DO NOT buy that blue plastic air line that everyone sells. I throw that crap out. The fittings leak so I put in good rubber air line that I had lying around. I only lost 10 LBS.
 
TSC is having a dollar day sale starting today Jan. 12th. They are listing a 50' retactable hose reel 3/8 heavy duty hose $59.99. I purchased two.
 
Cool Jeff

Its a bummer when you don't have enough air :lol: Congrats

DaddyDip

Thanks for the heads up :{_}: I may have to get a few too :!:

Billy
 
Back
Top