2444 question

SONNY

501 Club
SUPER dumb question here,----- The IH 2444 on the C-80 mower dies after the gas gets hot. pull line to carb off and no gas,---hold it for a few seconds and gas comes again, ---- good for a few hundred feet and dead again. Gas boils in the tank even with the heat gauge running at 180 to 220. Rad never boils, fins cleaned every time I mow.
Question here is, ---- I put an electric fuel pump on it yesterday and hooked it to the coil feed wire so it would run only with the key on and it ran 5 mins and pump died. Did the coil backfeed into the pump? OR the $2. chimineeese pump just junk out of the box? I have the same pumps on about everything I own and have never got a bad one.
I can run a wire direct to batt. and use an alligator clip for a switch. Cant get to any of the wires under the dash to hook directly to the key switch.
About ready to mount a tank behind the seat and not use the factory tank and try that.
Tractor runs fine til gas gets hot. It will run longer if I dump a gallon of real diesel fuel with 4 gallons of gas but still die. The mower dont pull all that hard and mowing roadsides and waterways I mostly run in second gear on the low side. If grass is shorter or thin I run in third and dont matter if half throttle or hammer down,--- still dies.
I moved the coil out a bit thinking that was the trouble then found the gas flow was the cause.
Open to ideas here!
 
I assume the tractor is 12-volt. If so, is there a ballast resistor in the ignition circuit that is reducing voltage to the pump? Are the pump and fuel lines a simple one-pipe-in and one-pipe-out or is there a loop back for excess fuel that returns to the tank or the line that feeds the pump? (If not, where is the heat in the tank coming from?)

Maybe the problem doesn't have anything directly to do with the pump. What was the problem yesterday before you put the pump on? Have you made sure the tank is clean and you don't have some junk drifting around that occasionally blocks the flow?
 
Sounds like a classic case of vapor lock. You may laugh, but look at the picture below. I do this on my Farmall A in extremely hot temp when bush hogging and working it hard. If you were around Ford cars or trucks back in the 60's, seems everyone that had a ford had a spring type clothespin or two on the fuel line, it acts as a heat sink. You can get a bag of 100 at Dollar General for $2.00, or 44 for a buck. May even have some at home right now.
 

Attachments

  • asset.jpg
    asset.jpg
    41.9 KB · Views: 11
Jim,---12 volt BUT never thought about the ballast thingy, and not sure if there is one. none showing that I can find. Could be up behind the dash. Everything crammed into small spaces on 2444's and super hard to get to without taking the tractor apart.
Pump is standard 1 line model.
Tank squeeky clean. --- motor heat goes back on the tank since this model has only a few inches between tank and motor block.
looks like carb gets hot enough to make enough pressure to keep gas from flowing from tank. Full tank runs good til it gets down to half, then motor starts running rough then just dies. --- Walk away and next day starts right up and mows til tank gets hot again!
I assume its vapor lock possibility too. The line is steel part way to carb then somebody added neo. the rest of the way. --- I just hooked on to the neo line from tank to pump inlet and added another neo from pump outlet to carb.
I mounted the pump outside the hood back by the side of the tank in hopes of keeping it cooler but the hot gas in the tank makes the pump just as hot so that idea went out the window in a flash!
I am going to put another pump on it and run power wire direct to batt. and see if that will work.
Still probably end up putting a tank behind the seat, or mount one on the crashbar in back.
I remember seeing the clothespins on gas lines on cars I junked back in the 60's. lol!
 
You could do a voltage check at the pump while the engine is running. Just going ahead and hot wiring it like you said could be the quicker way to check.

How about an exhaust leak? It probably would not take much of a leak if it is trapped under the hood to send a lot of heat to the gas tank.
 
super tight exhaust system,--this one is vertical so everything is on top. runs smooth and quiet.
Not sure if it has a thermostat in it or not,---probably does. Taking it out would help for a while maybe. Dont need one in the summer anyway and I dont run it in the winter. Sets at 180 mostly but has been 220 -- 230 depending on which way the wind is blowing. Rad never boils. Heat gauge could be off,--dont know.
Big job to get thermostat out. Could probably run without the hood on it,---- hate to cause it would look crappy.
 
Seems unlikely that the thermostat could cause that much heat at the fuel tank. Absolute numbers on temperature gauges are often a bit off. The question is whether (as you reported) it is now reading much more than it normally did in the past. Based on that, you may want to pull it out and see what happens. Is there any chance the hydraulic system is stuck at high pressure and the pressure relief valve is the heat source? I guess it wouldn't be a big effort to try running it with the hood off. Beyond that, I'm out of ideas.
 
It has ran this way ever since I have owned it. I bought it non runnin at the local "dump-it" auction 2 years ago. It was an ex-state of Illinois tractor at one time and had several owners since the state dumped it.
Gas cap is the tall one and I tried a new tall one and no change.
Hyd system open,---motor runs free and not under load. only pulls down when you raise the mower.
I tried different settings on the dist. to see if that helped,----it didnt so I set it where it sounds good and went with it.
 
Might have solved my gas problem.---- been runnin 5 gallons of REAL diesel fuel to 10 gallons of alki gas and now it runs smoother , has more power , PLUS runs cooler on hot days. Temp stays around 180 to 190 instead of 220 to 230 like before. Fuel tank still gets super hot but no vapor lock so far.
 
Back
Top