It looks like it is PTO problem season......
I asked last week about my PTO poppoing out of gear - check the shift lever and look at the splines i was told.
Splines looked good.
The lever pin had a flat spot on it, ordered a new one but it only lasted about 15 minutes..!!!
One of the suggestions was to weld a piece of drill bit in place of the worn pin - just did that and it has lasted longer than the one I bought.
BUT - when the PTO is engaged and under load (Woods 59 Belly Mower)there is a lot of pressure trying to force the lever towards neutral...at least it seems like a lot to me.
Under no load the lever 'clicks' in and out of gear smoothly and looking through the fill plug hole it seems to be engaged properly.
Maybe more wear on the splines than I think?
Just looked at 'gusbratz's pictures of his spline - mine doesn't look near that bad.....
This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
How much pressure on PTO shift lever
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 66
- Joined: Sun Jul 17, 2011 10:19 am
- Zip Code: 18923
- Tractors Owned: 1937 F-20
1944 M
H w/Heisler OD & disc brakes
C
C w/Fast Hitch
SC w/Fast Hitch
450
-
- Team Cub
- Posts: 11884
- Joined: Tue May 25, 2004 8:02 pm
- Zip Code: 80501
- Tractors Owned: Cubs, MH Pony, Shaw, Allis G, 1934 Silver King, JD LA and LI, Gibson D, David Bradley Tri-Trac
- Circle of Safety: Y
- Location: CO, Longmont
Re: How much pressure on PTO shift lever
You may have to pull the PTO out and also check the splines on the sliding collar. While out, take a good look at the pilot bushing and make sure it's still in good shape.
Bob
Bob
"We don't need to think more,
we need to think differently."
-Albert Einstein
we need to think differently."
-Albert Einstein
-
- 10+ Years
- Posts: 66
- Joined: Sun Jul 17, 2011 10:19 am
- Zip Code: 18923
- Tractors Owned: 1937 F-20
1944 M
H w/Heisler OD & disc brakes
C
C w/Fast Hitch
SC w/Fast Hitch
450
Re: How much pressure on PTO shift lever
The splines look OK to me - I'll try to get a picture - pilot bushing seems OK too, no play, no binding
-
- Cub Pro
- Posts: 4436
- Joined: Wed Dec 26, 2007 7:45 pm
- Zip Code: 32536
- Circle of Safety: Y
- Location: FL, Crestview
Re: How much pressure on PTO shift lever
If the lever is being forced back, then the splines are wore out either on the input shaft, the collar, or both.
Screwstick #3934
FCub - LoBoy - Numbered Series - Power Unit Databases
FCub - LoBoy - Numbered Series - Power Unit Databases
-
- 10+ Years
- Posts: 7153
- Joined: Sat Feb 18, 2006 8:12 pm
- Zip Code: 15101
- eBay ID: lacrosseorgans
- Skype Name: Mike.Hengelsberg
- Tractors Owned: 1949 Cub "Merlin"
1955 Cub "Lewis"
Cub Trailer
A-60 Blade
Cub-22 Mower
193 Plow - Circle of Safety: Y
- Location: PA, Allison Park (Am Hengelsberg)
Re: How much pressure on PTO shift lever
Agree with Raymond, but also check how much space is between the PTO shaft and the main shaft with the PTO installed and in neutral. There should be very little space there... If there is a lot of space, then the retainer for the transmission front seal may have been installed backwards and allowed the main shaft to slide forward.
-
- Cub Pro
- Posts: 23701
- Joined: Sun Feb 02, 2003 2:09 pm
- Zip Code: 63664
- Tractors Owned: 47, 48, 49 cub plus Wagner loader & other attachments. 41 Farmall H.
- Location: Mo, Potosi
Re: How much pressure on PTO shift lever
When everything is correct, it will actually engage at about the mid point of the lever travel. If it is only engaging right at the end, something is worn, the ends of the splines on the transmission shaft may be worn, the splines in the collar may be worn. Also, if the pilot bushing or the end of the pto shaft is worn it may put pressure on the shifter. I do not remember the history of your tractor, but if you recently purchased it you might need to check if the input shaft will slide forward and backward. that would indicate the front retainer on the input shaft is installed backward.
If you are not part of the solution,
you are part of the problem!!!
you are part of the problem!!!
-
- 10+ Years
- Posts: 1501
- Joined: Thu Oct 18, 2012 3:23 pm
- Zip Code: 13143
- Tractors Owned: 1957 Cub Low Boy w/ FH Mott Flail Mower
1953 Cub w/ sprayer and 54A blade (Chompers)
1954 Cub w/fast hitch (Ira)
1948 Cub ( Papa Paul)with Henderson loader..
1951 Mutt mix Cub (BattleAx
1950 Farmall Cub (basket case demo)
Cub parts tractor
2019 " KuB"ota 2601 loader and roto tiller
1951 Ferguson TEA 20 (parts)( Uncle Rusty)
F/H Disc Harrow for cub L-38
C-22 Sickle Bar Mower
IH C2 and C3 mower
Universal tool attachment with disc hillers..Rear cultivators (various tips
York Rake for Cub home made
Single bottom Plow for Cub F194
Gravely 5660 12 hp/ w snoblower.rototiller,bush hog - Circle of Safety: Y
Re: How much pressure on PTO shift lever
Check out the post I just put on gusbratz problem....
In Memory of 58,286
-
- 10+ Years
- Posts: 66
- Joined: Sun Jul 17, 2011 10:19 am
- Zip Code: 18923
- Tractors Owned: 1937 F-20
1944 M
H w/Heisler OD & disc brakes
C
C w/Fast Hitch
SC w/Fast Hitch
450
Re: How much pressure on PTO shift lever
OK - I'm convinced I have to repair/replace the mainshaft
Has anybody had any luck with welding then re-shaping the splines? I have a local welding/machine shop that does excellent work.
I haven't had much luck with the 'search function' (probably operator error.....) - How do you pull the mainshaft? Split at the engine and pull it forward or split it at the transmission and pull the shaft back out of the clutch then pull it forward from the transmission?? OR do you have to split it front and at the trans????
Has anybody had any luck with welding then re-shaping the splines? I have a local welding/machine shop that does excellent work.
I haven't had much luck with the 'search function' (probably operator error.....) - How do you pull the mainshaft? Split at the engine and pull it forward or split it at the transmission and pull the shaft back out of the clutch then pull it forward from the transmission?? OR do you have to split it front and at the trans????
-
- 10+ Years
- Posts: 7153
- Joined: Sat Feb 18, 2006 8:12 pm
- Zip Code: 15101
- eBay ID: lacrosseorgans
- Skype Name: Mike.Hengelsberg
- Tractors Owned: 1949 Cub "Merlin"
1955 Cub "Lewis"
Cub Trailer
A-60 Blade
Cub-22 Mower
193 Plow - Circle of Safety: Y
- Location: PA, Allison Park (Am Hengelsberg)
Re: How much pressure on PTO shift lever
You split where the transmission bolts to the torque tube. When you split there, the transmission pulls the main shaft put with it. Just be careful not to press down on the clutch pedal when you have it split, or the clutch disk will fall out of alignment and make it much harder to get things back together again.
It would be interesting to see what a welder could do with the shaft, but the cost of a new one or a good replacement may make more financial sense in this case. Also check the shaft for straightness.
It would be interesting to see what a welder could do with the shaft, but the cost of a new one or a good replacement may make more financial sense in this case. Also check the shaft for straightness.
-
- Similar Topics
- Replies
- Views
- Last post
-
- 8
- 469
-
by Dale Finch
Tue Nov 02, 2021 6:21 pm
-
- 4
- 190
-
by AndrewSpencer
Tue Aug 16, 2022 7:39 am
-
- 3
- 229
-
by Leewebb7
Mon Jan 29, 2024 4:12 pm
-
- 3
- 293
-
by Gary Dotson
Mon Dec 12, 2022 8:32 am
-
- 14
- 559
-
by ajhbike
Mon Apr 04, 2022 11:49 am
Who is online
Users browsing this forum: Bill V in Md, EIREfarmer, IHCubCadet147 and 3 guests