This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
pto shaft
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 29
- Joined: Sun Dec 13, 2009 3:47 pm
- Zip Code: 46164
- Tractors Owned: 1948 farmall cub,cub cadet 109
- Location: Nineveh,Indiana
pto shaft
has anyone ever seen a PTO shaft without the circlip groove on it. Mine dont have one. I looked really good. i thought that it may have been shered off but thats not the case. There not one at all.
-
- Team Cub Guide
- Posts: 5636
- Joined: Mon Nov 01, 2004 7:24 am
- Zip Code: 43528
- Tractors Owned: 47(circle cub),48(Floyd backhoe),49,,51,54 and another 55
- Circle of Safety: Y
- Location: OH, Holland
Re: pto shaft
The early ones didn't have the snap ring. The bearing was staked onto the shaft.
Rick
Rick
When I told my dad I've been misplacing things and doing stupid stuff----His reply---"It only gets better"
-
- 10+ Years
- Posts: 29
- Joined: Sun Dec 13, 2009 3:47 pm
- Zip Code: 46164
- Tractors Owned: 1948 farmall cub,cub cadet 109
- Location: Nineveh,Indiana
Re: pto shaft
Does anyone have pics or info on how it goes together. Im a little lost!
-
- 10+ Years
- Posts: 2917
- Joined: Sat Feb 11, 2006 5:26 pm
- Location: NC
Re: pto shaft
The staking had failed before I bought one of my tractors. I machined the lock ring groove in that shaft.
Luck favors those who are prepared
-
- Team Cub Guide
- Posts: 5636
- Joined: Mon Nov 01, 2004 7:24 am
- Zip Code: 43528
- Tractors Owned: 47(circle cub),48(Floyd backhoe),49,,51,54 and another 55
- Circle of Safety: Y
- Location: OH, Holland
Re: pto shaft
Hopefully one of these pics from TM will show you what you want. I can't locate the page in the manuals. http://www.tm-tractor.com/gpt/gpt_001.htm
Rick
Rick
When I told my dad I've been misplacing things and doing stupid stuff----His reply---"It only gets better"
-
- Team Cub Guide
- Posts: 5636
- Joined: Mon Nov 01, 2004 7:24 am
- Zip Code: 43528
- Tractors Owned: 47(circle cub),48(Floyd backhoe),49,,51,54 and another 55
- Circle of Safety: Y
- Location: OH, Holland
Re: pto shaft
I'd install the new seal into the outside of the cast housing first, then install your shaft (with bearing attached) into the cast cover housing from the inside, then once your shaft is in place, you'll install the shield with the big snap ring that snaps into the cast cover. A search will show you the easiest way to install the unit back into the diff/trans housing. I'm sure others will also pitch in to add their shortcuts.
Rick
Rick
When I told my dad I've been misplacing things and doing stupid stuff----His reply---"It only gets better"
-
- 10+ Years
- Posts: 321
- Joined: Wed Jan 21, 2009 2:17 pm
- Zip Code: 78736
- Tractors Owned: two 1948 Cubs
1951 Super A
Kubota L2350 - Location: Austin, TX
Re: pto shaft
I'm rebuilding my PTO and it had a staked shaft, no snap ring groove. I thinking about buying a new shaft with snap ring groove and I see a lot of replacement shafts for sale on ebay all the way from $15 to $70. How is the quality of these compared to the original shafts? What about the shaft TM tractor sells, anyone have one and how is it?
Are they heat treated to make them hard enough to last?
Gerry
Are they heat treated to make them hard enough to last?
Gerry
-
- Cub Pro
- Posts: 23701
- Joined: Sun Feb 02, 2003 2:09 pm
- Zip Code: 63664
- Tractors Owned: 47, 48, 49 cub plus Wagner loader & other attachments. 41 Farmall H.
- Location: Mo, Potosi
Re: pto shaft
If you want to reinstall it, make sure the bearing is good, then clean the inner race good, as well as the shaft. There is a product called bearing mount that is similar to Loctite Thread Locker, but is more permanent. Put it on the shaft before sliding the bearign into place, then use a center pumch to raise dimples on the shaft . Between the two of them you should not have any more problems.
If you are not part of the solution,
you are part of the problem!!!
you are part of the problem!!!
-
- 10+ Years
- Posts: 321
- Joined: Wed Jan 21, 2009 2:17 pm
- Zip Code: 78736
- Tractors Owned: two 1948 Cubs
1951 Super A
Kubota L2350 - Location: Austin, TX
Re: pto shaft
I pressed on my new bearing and it went on good and tight so I'm ok. It was originally staked two places, I re-staked it in 3 places. I didn't use bearing mount since it went on tight. I wanted to use my old shaft, I'm just not sure the replacement shafts are up to snuff.
Gerry
Gerry
-
- Cub Pro
- Posts: 10540
- Joined: Mon Aug 09, 2004 10:14 pm
- Zip Code: 02840
- Location: RI, Newport
Re: pto shaft
Just a thought, I replaced the last couple with a sealed bearing. It's a 6205 (6205 2RS has rubber seals) and very common.
The last one I got through a dealer was unmarked, made in China and the same price I paid for an SKF sealed bearing (delivered!). With a sealed bearing there is some drag, but you may be able to get away without replacing the seal and you can ignore the grease fitting. The 1977 Cub had about 1/2 a tube of grease in the transmission, somebody must have pumped it 'full' of grease.... or till the tube was empty .
The last one I got through a dealer was unmarked, made in China and the same price I paid for an SKF sealed bearing (delivered!). With a sealed bearing there is some drag, but you may be able to get away without replacing the seal and you can ignore the grease fitting. The 1977 Cub had about 1/2 a tube of grease in the transmission, somebody must have pumped it 'full' of grease.... or till the tube was empty .
1971 Cub (Rufus) 1950 Cub (Cathy) 1965 Lo Boy Fast Hitch (Nameless III) 1970 Cub 1000 Loader & Fast Hitch (Lee)
-
- Similar Topics
- Replies
- Views
- Last post
-
- 3
- 315
-
by Dale Finch
Sat Jan 22, 2022 8:33 am
-
- 4
- 232
-
by yaesukk4lgt@yahoo.com
Thu Oct 28, 2021 6:32 am
-
- 3
- 251
-
by rterry
Tue Jul 18, 2023 10:28 am
-
-
Broken Differential Shaft?? Attachment(s)
by Dale Finch » Thu Mar 14, 2024 10:29 pm » in Farmall Cub - 7
- 372
-
by radioguy41
Sat Mar 16, 2024 3:11 pm
-
-
-
Pitman arm removal shaft end - how? Attachment(s)
by inairam » Sat Feb 12, 2022 4:34 pm » in Farmall Cub - 7
- 540
-
by Glen
Sun Feb 13, 2022 7:25 pm
-
Who is online
Users browsing this forum: No registered users and 6 guests