This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
Ih carb
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 1776
- Joined: Thu Oct 26, 2006 7:17 pm
- Zip Code: 44657
- Circle of Safety: Y
- Location: Minerva,Ohio
Ih carb
Cub would only run with full choke. Removed carb and inlet screen plugged. Noticed it had two bowl gaskets, so I took it apart and it was warped very bad. I straightened it as close as I could using a vise, c clamp , adjustable wrench and a file. I’m sure the gasket will take care of the rest.
I tried spraying cleaner through the idle tube but it is plugged. Ran wire through it but no help. I see I can buy new tube but how is it in there? Just a press fit or threaded? Don’t want to ruin anything. I have it soaking in solvent now, maybe that will open it up
John
I tried spraying cleaner through the idle tube but it is plugged. Ran wire through it but no help. I see I can buy new tube but how is it in there? Just a press fit or threaded? Don’t want to ruin anything. I have it soaking in solvent now, maybe that will open it up
John
'49 Cub (Vince)
'41 allis B with Woods L59 mower
656 Wheel Horse with 42” sickle mower
C-165 Wheel Horse
Simplicity 20 HP Sunstar
Honda 48” walk behind mower
'41 allis B with Woods L59 mower
656 Wheel Horse with 42” sickle mower
C-165 Wheel Horse
Simplicity 20 HP Sunstar
Honda 48” walk behind mower
-
- Cub Pro
- Posts: 7508
- Joined: Thu Aug 31, 2006 7:00 pm
- Zip Code: 02769
- Tractors Owned: 6"F" cubs
5 lo-boys
1 154
1 184
1 IH444
1 Oliver OC3 crawler
1 AC D10
1 IH 100 manure spreader
1 IH model B corn grinder
3 power units
cub demonstrator - Circle of Safety: Y
- Location: Ma. Rehoboth
-
- 10+ Years
- Posts: 1776
- Joined: Thu Oct 26, 2006 7:17 pm
- Zip Code: 44657
- Circle of Safety: Y
- Location: Minerva,Ohio
Re: Ih carb
Thanks
'49 Cub (Vince)
'41 allis B with Woods L59 mower
656 Wheel Horse with 42” sickle mower
C-165 Wheel Horse
Simplicity 20 HP Sunstar
Honda 48” walk behind mower
'41 allis B with Woods L59 mower
656 Wheel Horse with 42” sickle mower
C-165 Wheel Horse
Simplicity 20 HP Sunstar
Honda 48” walk behind mower
-
- 10+ Years
- Posts: 994
- Joined: Mon Feb 03, 2003 11:10 am
- Zip Code: 40023
- Tractors Owned: 1948 FCub
1957 LoBoy - Circle of Safety: Y
- Location: KY, Fisherville
Re: Ih carb
Just fought this myself...carefully unscrew it from the carb. Using carb cleaner and the wire you can clear the tube and reuse it.
Ken, Annie the '48.
I think we gotter if'n she don't jump, Andy Griffith.
I think we gotter if'n she don't jump, Andy Griffith.
-
- Team Cub
- Posts: 11862
- Joined: Tue May 25, 2004 8:02 pm
- Zip Code: 80501
- Tractors Owned: Cubs, MH Pony, Shaw, Allis G, 1934 Silver King, JD LA and LI, Gibson D, David Bradley Tri-Trac
- Circle of Safety: Y
- Location: CO, Longmont
Re: Ih carb
The orifice opening is .021, so it needs to be a fine wire or sewing needle. While holding it tightly with pliers or vice grips, wiggle it back and forth a few degrees until it starts to loosen. If you just try to unscrew it there is a good chance you'll twist it off. McDonald Carb sells replacement idle needles for much less than OEM.
Edit: I meant to say McDonald Carb sells replacement idle "TUBES".
Edit: I meant to say McDonald Carb sells replacement idle "TUBES".
"We don't need to think more,
we need to think differently."
-Albert Einstein
we need to think differently."
-Albert Einstein
-
- 10+ Years
- Posts: 1776
- Joined: Thu Oct 26, 2006 7:17 pm
- Zip Code: 44657
- Circle of Safety: Y
- Location: Minerva,Ohio
Re: Ih carb
Bob McCarty wrote:The orifice opening is .021, so it needs to be a fine wire or sewing needle. While holding it tightly with pliers or vice grips, wiggle it back and forth a few degrees until it starts to loosen. If you just try to unscrew it there is a good chance you'll twist it off. McDonald Carb sells replacement idle needles for much less than OEM.
Thanks, I have a torch tip cleaning wire I can use. If I take out the idle screw and push a wire up the tube, shouldn’t I be able to see it through where the screw came from?
'49 Cub (Vince)
'41 allis B with Woods L59 mower
656 Wheel Horse with 42” sickle mower
C-165 Wheel Horse
Simplicity 20 HP Sunstar
Honda 48” walk behind mower
'41 allis B with Woods L59 mower
656 Wheel Horse with 42” sickle mower
C-165 Wheel Horse
Simplicity 20 HP Sunstar
Honda 48” walk behind mower
-
- Team Cub
- Posts: 11862
- Joined: Tue May 25, 2004 8:02 pm
- Zip Code: 80501
- Tractors Owned: Cubs, MH Pony, Shaw, Allis G, 1934 Silver King, JD LA and LI, Gibson D, David Bradley Tri-Trac
- Circle of Safety: Y
- Location: CO, Longmont
Re: Ih carb
I think you'll need to clean the idle tube from the threaded end after it's removed. I think they are made by crimping in a short plug that is drilled and then the outside threaded. That would make it difficult to "find" the opening if it's clogged or corroded shut by inserting anything down the length of the idle tube. There is only about 1/8" of 4-48 threads.
"We don't need to think more,
we need to think differently."
-Albert Einstein
we need to think differently."
-Albert Einstein
-
- 10+ Years
- Posts: 1776
- Joined: Thu Oct 26, 2006 7:17 pm
- Zip Code: 44657
- Circle of Safety: Y
- Location: Minerva,Ohio
Re: Ih carb
Bob McCarty wrote:I think you'll need to clean the idle tube from the threaded end after it's removed. I think they are made by crimping in a short plug that is drilled and then the outside threaded. That would make it difficult to "find" the opening if it's clogged or corroded shut by inserting anything down the length of the idle tube. There is only about 1/8" of 4-48 threads.
Ok thanks, I was hoping not to try to take it out. I better wait to order the rebuild kit from TM until I get it out With my luck, I’d ruin it and have to buy a new one.
'49 Cub (Vince)
'41 allis B with Woods L59 mower
656 Wheel Horse with 42” sickle mower
C-165 Wheel Horse
Simplicity 20 HP Sunstar
Honda 48” walk behind mower
'41 allis B with Woods L59 mower
656 Wheel Horse with 42” sickle mower
C-165 Wheel Horse
Simplicity 20 HP Sunstar
Honda 48” walk behind mower
-
- Team Cub
- Posts: 24273
- Joined: Tue Aug 07, 2007 3:39 pm
- Zip Code: 45030
- Tractors Owned: At This Time
40 Farmall Cubs (Round Hood)
2 Farmall Cub (Square Hood)
2 IH Cubs (Square Hood)
5 Lo-Boys (Round Hood)
2 Lo-Boys (Square Hood)
2 Farmall 404's
1 Farmall H
1 Ferguson 20
1 Cub Cadet 125
1 Kubota B-7100 - Circle of Safety: Y
- Location: OH, New Haven (Hamilton County)
Re: Ih carb
The meter jet is a piece of cake. It solved my problem with having to run with a full choke.
There are two ways to get enough Cubs. One is to continue to accumulate more and more. The other is to desire less.
-
- 10+ Years
- Posts: 1776
- Joined: Thu Oct 26, 2006 7:17 pm
- Zip Code: 44657
- Circle of Safety: Y
- Location: Minerva,Ohio
Re: Ih carb
Barnyard wrote:The meter jet is a piece of cake. It solved my problem with having to run with a full choke.
Mine was clear. The inlet screen was plugged with rust and dirt.
'49 Cub (Vince)
'41 allis B with Woods L59 mower
656 Wheel Horse with 42” sickle mower
C-165 Wheel Horse
Simplicity 20 HP Sunstar
Honda 48” walk behind mower
'41 allis B with Woods L59 mower
656 Wheel Horse with 42” sickle mower
C-165 Wheel Horse
Simplicity 20 HP Sunstar
Honda 48” walk behind mower
-
- 10+ Years
- Posts: 1776
- Joined: Thu Oct 26, 2006 7:17 pm
- Zip Code: 44657
- Circle of Safety: Y
- Location: Minerva,Ohio
Re: Ih carb
john2189 wrote:Barnyard wrote:The meter jet is a piece of cake. It solved my problem with having to run with a full choke.
Mine was clear. The inlet screen was plugged with rust and dirt. That’s why it wasn’t getting gas.
'49 Cub (Vince)
'41 allis B with Woods L59 mower
656 Wheel Horse with 42” sickle mower
C-165 Wheel Horse
Simplicity 20 HP Sunstar
Honda 48” walk behind mower
'41 allis B with Woods L59 mower
656 Wheel Horse with 42” sickle mower
C-165 Wheel Horse
Simplicity 20 HP Sunstar
Honda 48” walk behind mower
-
- Team Cub Mentor
- Posts: 17489
- Joined: Mon Feb 03, 2003 6:45 am
- Zip Code: 21550
- Tractors Owned: "1950 Something" Farmall Cub
1957 Farmall Cub w/FH
1977 International Cub w/FH
1978 International Cub
1948 Farmall Super A - Circle of Safety: Y
- Location: MD, Deep Creek Lake
Re: Ih carb
John,
Bring it down to The Cub Tug and Bob and I will go over it.
Bring it down to The Cub Tug and Bob and I will go over it.
-
- 10+ Years
- Posts: 6152
- Joined: Mon Mar 19, 2012 7:33 pm
- Zip Code: 00000
- Tractors Owned: 1956 Farmall Cub with Fast Hitch, F-11 plow, Disc, Cultivator, Cub-22 mower
- Circle of Safety: Y
- Location: Wa.
Re: Ih carb
Hi,
Below is a listing at TM Tractor for a new idle tube, you can see the threads on the end.
http://www.tmtractor.com/new/fl/384fp.htm
Below is a listing at TM Tractor for a new idle tube, you can see the threads on the end.
http://www.tmtractor.com/new/fl/384fp.htm
-
- 10+ Years
- Posts: 1776
- Joined: Thu Oct 26, 2006 7:17 pm
- Zip Code: 44657
- Circle of Safety: Y
- Location: Minerva,Ohio
Re: Ih carb
Don McCombs wrote:John,
Bring it down to The Cub Tug and Bob and I will go over it.
Wish I could, but have to work
'49 Cub (Vince)
'41 allis B with Woods L59 mower
656 Wheel Horse with 42” sickle mower
C-165 Wheel Horse
Simplicity 20 HP Sunstar
Honda 48” walk behind mower
'41 allis B with Woods L59 mower
656 Wheel Horse with 42” sickle mower
C-165 Wheel Horse
Simplicity 20 HP Sunstar
Honda 48” walk behind mower
-
- Team Cub
- Posts: 11862
- Joined: Tue May 25, 2004 8:02 pm
- Zip Code: 80501
- Tractors Owned: Cubs, MH Pony, Shaw, Allis G, 1934 Silver King, JD LA and LI, Gibson D, David Bradley Tri-Trac
- Circle of Safety: Y
- Location: CO, Longmont
Re: Ih carb
Are you close to anyone who could bring it to the Tug and then return it to you?
"We don't need to think more,
we need to think differently."
-Albert Einstein
we need to think differently."
-Albert Einstein
-
- Similar Topics
- Replies
- Views
- Last post
-
-
Identification of my Engine and Carb - in order to get a new Carb
by JKaechler » Tue Dec 07, 2021 9:25 pm » in Farmall Cub - 14
- 627
-
by Don McCombs
Thu Dec 09, 2021 11:42 am
-
-
- 4
- 203
-
by Don McCombs
Fri Aug 06, 2021 10:08 am
-
- 11
- 419
-
by Duwop
Tue Aug 17, 2021 4:33 am
-
- 2
- 171
-
by Jim Reid
Tue Apr 05, 2022 10:59 am
-
- 3
- 189
-
by Bob McCarty
Wed Oct 06, 2021 4:47 pm
Who is online
Users browsing this forum: wrz and 6 guests