Wood Stove Help???

Mag Man

501 Club
Hi Guys,

I have a fisher air tight stove, Its a moma bear actually with one door and two round air vents that open and close on the front on that door.

Now I started my first fire yesterday but I do not really understand how to operate this beast. I have no pipe dampers just the 2 things in the front and about 1/2 hour after my fire was started myuy lower pipe started to smoke like crazy and stunk the garage up with smell and smoke. Was this just the new paint burning on the pipe? Did I get it too hot? and if any one uses one of these type of stoves how do you use the drafts? I can not seem to get much heat. Leave them somewhat open close them after fire is going or leave them open for a certain amount of time??
JON
 
Hi Jon. Those two dampers in the front should turn in and slow down your amount of fire, or open up and increase. It's sometimes not a super fast process, but eventually works. If your stove pipe exits straight out the top of the stove, you may need to install a butterfly damper in that pipe(fairly easy to do). You can slightly close that top damper then and somewhat keep some heat in the stove, instead of everything going right out the chimney. Your pipe started smoking because you did get things burning hot, but if you have new stove pipe, that'll happen a few times. I bought me a cheap metal oven thermometer and set by my stove pipe and now have an idea on various temps and can turn my dampers in or out and keep things fairly constant. It'll take a few days and you'll have it down pat. Check to make sure your gasket is sealing good around your door, if it has one. If everything is sealed good, you should be able to almost smother the fire out by shutting those dampers.

Rick
 
The idea is to start a small fire and when it is going good to add larger wood. Wood gives off combustible gases when first burning. These gasses include the creosote. If you put too much wood at one time and choke it down(close the drafts) You get a smoky fire with cool flue gases that deposit creosote on the inside of the flue. I have a magnetic temp gauge on my stove pipe. With it you can tell if you are burning too hot or too cool. TSC has these thermometers.
 
It all sounds like good advice. Really, until you initially create and maintain enough heat to get a warm air draft moving up the pipe the dampers don't do that much.
Until this year, I have used the same stove for 25 years. I bought the stove new from a local manufacturer. This past summer, I got a good deal on a "Lilly" stove, and installed it. This Lilly stove is so much better than my old one. It's twice as heavy, with a cast iron fire door and ash door. The squirrel cage hot air fan is a fraction of the noise created by the old one and seems much more efficient. This stove is airtight and has a more even burn time than the old one. On my old stove I needed a pipe baffle, or damper, to help control the heat. Before, I had to constantly shovel the ashes from the bottom. With this new one, there's a door to open and a pan slides out. No more fine gray ash all over the place.

What I need to remember is that occasionally the stove must be operated at high temp to remove the creosote build-up that forms at low temps.

It pays to look around before you buy a unit that you'll be using for years.
Larry
 
Mag Man, The Momma Bear stove IMHO is the best stove around. I had one years ago and like an idiot I sold it. Been looking for one for 2 years (Don't know what happened to Fisher) and finally bought a wonderwood. Also a good wood burner. I know at least 5 people that have the momma bear and none of them use a damper in the pipe. All is controled by the 2 dampers on the stove. It won't take long to figure it out. If ya don't like it we can start the Cub Express :wink: :wink: The pipes giving off an odor will quit before you know it. You alrady know keeping your flue cleaned is utmost important. Enjoy. grump

PS It takes a while to build a good fire before you get the real heat from the stove. Get er goin good and close down the dampers most of the way and she'll heat :) :)
 
until you initially create and maintain enough heat to get a warm air draft moving up the pipe the dampers don't do that much.
I have to disagree with you slightly Larry, at least with my Grizzly air tite. When I start a fire, I have two options.I can either crack the doors slightly to create a swift draft blowing across the wood, or open the door dampers enough to creat that same fast draft. Once the fire is completely going, I regulate the dampers and slow things down abit. I have a 7" x1/4" thick boiler pipe 34 foot tall, with great draft, so maybe that's why mine works so well.

I agree with you about
stove must be operated at high temp to remove the creosote build-up that forms at low temps.
. I have a stove that is abit smaller than needed, rather than too big. This way I run things hotter. The only time I cut things back is when I'm outside all day, no need for the house to be toasty warm 75 degrees for 8 hours.

Rick
 
Another thought. Use the heavy gauge metal pipe that is welded and not that thin stuff that slips together. It lasts longer. Even that eventually goes.
 
I have a cold chimney (old timers know what this is), and getting a good movement up the flue is a problem, so I keep a container of charcoal soaked in kerosene outside. When I want to start a fire, 2 or 3 bricks get it going fast and do a good job of preheating the chimney.
 
Son is using an Ashley wood stove/furnace. The Ashley has two thermostatic controlled dampers on the side of the stove and we put one damper in the stove pipe. As the others have stated - it takes a bit of experience to get things set properly.

Neighbor heats his work shop with a wood furnace. Both neighbor and son use a box fan set on low to circulate the heat. Son has a thermostat that comes on when the heat above the stove reaches 90 degrees to circulate the heat.
 
Rick said,
I have a 7" x1/4" thick boiler pipe 34 foot tall, with great draft, so maybe that's why mine works so well.
I stand corrected. Unfortunately I received only the standard sized flue. However, when sufficiently warmed, does an outstanding job. Some guys have all the luck!
Larry
 
Hi Jon
I ran a Fisher (PAPA) for about ten years,good heat no problem.Like someone else said it will take awhile to get to know the stove.I did not use a flew pipe damper.When you are ready to light up,open the drafts full.This will give you good draw.If you have a problem light a piece of paper and holding it near the flew pipe inside the stove,the heat will create a draw. I used to clean my chimney quite often beause I had a outside chimney,which causes more creosolt. You can close the drafts as you wish to gain more heat, during the day I used to run mine open.You will also need a metal bucket with cover for removing the ashes.Good luck. 8) :) Bruce
 
yep. you will get the kinks worked out of it. too me a few tries too. coming downstairs and the basement full of smoke here b/c i did not have enought heat for the furnace to draw the smoke out so the smoke was "puffing" out of the door! shew wee. stinky stuff the first few times. we hooked our wood furnace to our central flue (sp?) supply that heats our entire house, the wood furnace has a thermostat and two blowers on it to send in the heat! sometimes it kicks on the fans to the house furnace. either way, if the blowers are off, we still have a steady supply of heat coming out of our home vents. toasty warm! Ron had it 78 degrees in here Friday night! almost had a heat stroke! this furnace came from Tractor Supply Co. and we bought it 3 years ago, this being our third winter with it, we sometimes use the wood pellets depending upon how quick and how hot we want our fire. when we get it going good, we only open the damper on the bottom drawer where the ash pan is one complete turn away from closed so it draws in just enough air to keep everything simmering and it burns good and slow. it also will take about a 28 inch piece of wood if i remember correctly! it is a US Stove Co. HotBlast 1537M. it is a bid green wood eating machine. it will also take coal. but we will probably never go that route. good luck with yours! i am sure you will be warm real soon :D
 
One more thing, if your house is real tight you may need to supply outside air into the room where the stove is to get it to draw right. I had problems with mine at first, then I tried opening a basement window, which solved the problem. After trying it for a while I drilled through the plate and ran a 1 1/4 inch pvc pipe form the outside down the wall and ended it directly behind the stove. I slip a cap over then inside end when not using the stove, and also one on the outside in the summer time to keep insects from building in it.
 
I have a Woodstock Soapstone fireview in a newer construction home. I had to add the an outside air adapter for the stove to pull a draft. I ran flexible dryer venter through the hearth into the basement and out the rim joist in the form of a dryer vent. I just removed the flapper, as it flapped the wrong way. Works great, no smoke in the house. I heat my entire 2 story 2,100 sq ft home with the stove. Only when the temps stay below about 10 degrees for several days in a row do I have to kick the furnace on.
 
I only heat with wood. I use a pipe damper along with the dampers on the stove. I also use two temp gages one on the stove and one on the pipe to regulate the heat out put in the stove and to regulate the heat going up the chimney to prevent creosote. Each stove installation is different and acts different too.

First the rule of thumb is to have the chimney pipe 25% larger than the stove pipe for draft on windless nights/days.

Example; If your stove pipe is 6" diameter your chimney pipe should be at least 8" diameter for good draft all the time.

My old house had a metalbestos 8" chimney(stainless) with a 6" stove pipe and i never had any chimney problems at all.

Now my new house with the clay chimney 8"x11" is a different system. I blocked off the fireplace with a steel plate with a 6" hole for the stove. I learned to light a piece of news paper first to get the draft going then put in the kindly and firewood and its good to go. Like i said each system has its quirks too.

With a gage on the stove i can regulate the temp and how fast the wood burns too without causing creosote. I can also regulate the heat going up the chimeny too with a gage on the pipe and a damper on the 6" pipe too. I have the wood burning down to a science now with this setup. I'm getting the best quality heat output that i can and burning less wood too at the sametime. You don't need to fill the stove to get the proper heat output.
BB
 
Back
Top