Window reglazing tricks?

Paul_NJ

501 Club
Does anyone have any tricks to achieve a nice smooth surface on window glazing? I've been reglazing old windows to be used in my barn workshop project for years, but it seems like I've never worked out a technique as good as I'd like. Sometimes it goes just right, and sometimes it's a fight to get smooth putty runs.

I use DAP 33, and have learned that it doesn't store well, that you need a warm, fresh product to begin with. But I still often get "separations" on the final smoothing stroke with the knife. I was thinking about dipping the putty knife in mineral spirits once in awhile to reduce drag and improve smoothness. Then again I don't want to affect the drying characteistics either. Maybe alcohol or water would work better. Does anyone do that?

I just started on a 5 over 5 window last night, and I'd sure like to minimize the aggravation. Just thought I'd ask.

Thanks
 
You need to work DAP33 in your hands to soften it up. Work the glazing until it's quite soft. Mineral spirits will help to smooth out the final pass.

I have a gallon can of DAP33 that is several years old. It does seperate with age, but again you have to work in by hand in preperation for glazing.
 
The problem I have with old DAP 33 is that even when the top is replaced firmly, it dries on the surface, and then the dried skin doesn't mix in with the softer middle.

I did discover an improvement today . . . keep a little jar with mineral spirits next to you, dip the knife after each smoothing pass,and wipe it off with a rag before the next pass. That seemed to help minimize the drag on the putty, leaving a nice smooth surface.
 
next time you close the can up, put a piece of kitchen plastic wrap on top of the putty and press it down. Eliminates the air inside the can from contacting the putty and drying it out. Works for drywall too.
 
Thanks for all of the suggestions! I got alot of good ideas, and realized it's not only me who struggles with reglazing neatly.
 
Paul:

In my antique restoration projects, I sometimes have to reglaze old windows etc., and I even do a few of my own ocassionally. I am not familiar with Dap 33 per se, but it's description sounds like normal run of the mill glazing putty that you have to work in your hands to achieve the desired working consistency.

One trick we used to use (my dad and his peers) was to use a little mineral oil.. dip your hands in it and use it to help work the putty. You could also use the mineral oil to coat the knife for an effortless and smooth slide. When the knife is angled between 15 and 30 degrees I guess, coated with a light coat of mineral oil, very few wrinkles, skin breaks or other imperfections result.

That is one way that I was taught and have used for years. Conditions, end result and prices may vary :big give up: :big smile:
 
Thanks Rudi

I don't think I've ever posted a question, no matter how far off it might be, that I haven't received answers, suggestions, and experiences from multiple sources all looking to help. This is a great community to be a part of!

Paul
 
I've glazed a lot of windows over the years, first off you do need to paint the sash with linseed oil, sometimes two coats, if the wood is badly dried out it will suck the oil out of the glazing compound and it will fall out in a very short time. It the sash is really bad sometimes I will go so far as to paint it with the glass out, that way it protects the wood AND keeps the glazing compound from getting too dry.

Old window putty used to dry and get hard, and it worked pretty well but is a real pain to get out when you have to replace the glass.

Glazing compound (such as Dap 33) is supposed to stay semi moist for many years, it will get a skin over it to help keep it from getting damaged or distorted, but underneath it stays moist for a long time. I also like to paint the glazing compound after it's been in for a couple of weeks.

The guys were also right about "working" the putty in your hand. The softer you make it the easier it is to put in and smooth out.

The kind of knife you use makes a big difference too. A stainless steel knife will work much better than a steel one. Red Devil and other companies make a knife that is made just for glazing one end is flat for putting the putty in and the other end is bent and has a short split in the crease, they work pretty good. Unless the window is still in the house and then you can't get the knife into the corners very well. Sometimes it seems like no matter what you do there will still be some separations or tearing of the glazing compound when you smooth it out, when that happens, I usually just spit on my finger and swipe lightly across it going the other direction.

I try to never buy a whole gallon (I always think that if I just have a quart, I won't have to do so much glazing) Anyway, when I open a new quart I take out the entire contents of the can and work it in my hands, usually in two lumps... I use what I need and put the rest in a ziplock bag, squeeze all the air out of the bag zip it shut and put it back into the can, bag and all. It stays “fresh” almost forever like that.
 
Back
Top