Wheel Bolts and Mowers

K

Kirk

501 Club
Good Morning to All,

I have a couple of questions for you:

1. I need to replace a number of the rear wheel bolts/carriage bolts on the Cub. Some holding the center peice to the outer rim as well as several of the bolts supporting the wheel weights. Are the bolts purchased at Home Depot of a grade that's acceptable? :? I can't seem to find any with the "grade markings" on them......though I haven't tried looking at the tractor store.

2. On the "home page" of Farmall Cub.Com one of the pictures that rotate are of Syden Stricker mowing his "gorgeous" yard. :wink: What type of mower is he using. It appears to be something used on golf courses. And where could one be purchased?

Many thanks,
 
Try TM tractor parts or J.P. Tractor Salvage for your wheel bolts.

The mower you mentioned is a Mott flail mower. It is the type they use for highway mowing in some areas. It is not considered a true "finish" mower. The final cut produced will not be as clean as a finish mower, but would be somewhat better than a "brush hog" type mower. You will occasionally see them offered for sale on the classified ads of this site and ytmag.com as well as e-bay.
 
Kirk, as BD said the mower is a flail, which has a center shaft with knives mounted on pivots, wheras most golf courses use reel type mowers. The flail does a fairly good job of mowing for a lawn, but does not have any lift, so if anything is laying down it doesn't get cut. The flails greatest advantage, is that it won't throw rocks or sticks as a rotary will. They are primarily a rough service mower. They do have a disadvantage that they will wrap up in tall stringy grass, such as Fescue.
 
http://www.mcmaster.com/

has an excellant selection of hardware. i ordered grade 5 carriage bolts in 2" (front) and 3" (rear) wheel weights. packs of 10 bolts. fast shipping.
they have square heads, also, but I have to look further to check grade.

I have also found Lowes to be much better in supplying misc. hardware than Home Depot around here. grade 8 hardware, 10" 1/2 13 bolts, stuff like that.
 
Kirk- If you have trouble locating the square headed rim bolts I had them made by my machinst niehbor. I'm sure he would make more if needed. Otherwise McMaster Carr will be your best bet. mcmaster.com or call 330-995-5500. I've used them countless times for everything fron A-Z. If you can't find it there it will be hard to find. Best sourcing catalog out there. Do't hesitate to call if you don't find it online or in there cat. They will find it for you if you call and till them what you need.
 
I have to disagree with the statments that the Mott mowers don't lift the grass for cutting. I have a 6 footer 3 pt behind my 9N and a 4 footer belly mount under my Cub #2. I found the Mott does a better job of cutting the grass that the tractor tires have bent down and can't be seen after mowing. They also do a better job of spreading the clippings out. After I finish mowing with my 6 foot rotary rear discharge and 4 foot rotary side discharge I can still see the tire marks. Not with the Motts.
The Motts are a lot more maintanance intensive. Especially the roller bearings. I have been thinking of a modification to make the bearing a lot easyer and cheaper to change.
 
You guys are the BEST!!

I now have McMasters saved in my "favorites" of which looks like a great & intereting site.

And as for the mower.....well, I'm just excited to have some experts out there that have "been there, done that" experience.
 
Kirk,

The McMaster-Carr catalog is a great thing to have. With over 3,000 pages if you can't find something you need you don't need it. :lol: :lol: Real good folks to deal with and shipping is quick. You can get a written version of the catalog just for the asking and it will be at your door in a day or two. If you don't have the number here it is: 562.692.5911


No I don't work for them. :lol: :lol: :lol:
 
You must log in or register to reply here.
Back
Top