What Type of Mask is Needed

Dan England

501 Club
I have never worn a mask while using the riding mower on the lawn nor when using a Cub and implements. I will need to do so this summer if/when I use machinery as taking in dust particles now causes coughing and other respiratory problems. The mask will need to filter out dust, pollen, grass fragments, whatever particle size one would get when mowing. I haven't shopped yet to see what types of mask are available but need advice on what to purchase. Would the cheap ones which are used one time and discarded, usually held in place by a couple of rubber bands be sufficient or should I go for a more expensive model? Your help is appreciated. Dan
 
Dan - I would think that the disposables would be sufficient. You might pick up a package of them and take the specs from the package to your doctor to be sure he felt they would do the job. Better safe than sorry .
 
Dan I think Bigdog is right on getting the specs from the usual disposable masks. I think I would also look at the $20 to $30 masks used for painting as well. These are not the ones needed when using paints with hardeners etc, but are also a lot more efficient than the one time use, throw away type filters. Just my HO. Pete
 
Dan,
I use a mask while mowing, espically when on the lawnmower. I prefer to use the cub because it gets me up higher out of a good bit of the dust. I used the disposable for a while but couldn't get a good fit. It let too much junk get in around the nose and bottom of my chin. I finally found a mask at a electronics salvage store in Atlanta :? and I bought all 3 he had. They have no name on them but I think they are probably somewhere between a disposable and a good painters mask. They are made of a rubber type material which is a flesh color and have a thick, almost felt like filter material. I have used them for 2 years and wash them by hand after about 2 or 3 uses. I'll try and post you a picture and look again for a name tonight when I get home.

Ron
 
Dan,
Bigdog makes a good suggestion. I have used the cheap disposable masks while mowing and find that they can help a lot. A big factor is how well they fit (and thus seal to your face at the edges). There is a metal band at the top that you can bend to get a fit around your nose. Positining of the ruber band (higher/lower) can help too. How long I can use one depends on how dusty it is (the season!). I use it until it is visibly dirty (subjective) or the band breaks (objective).

You will probably find most inexpensive disposables confirm to "N95" and the differences (and cost) relate to how they fit and how long they can be comfortably worn.

I suggest you take a look at this page for good general information.
http://multimedia.mmm.com/mws/mediawebserver.dyn?6666660Zjcf6lVs6EVs66Smi4COrrrrQ-

Look here at some specific products. Be sure to look at the datasheets for 8000 and 8211 to get a feel for the differences on fit and use time.
http://www.mpsupplies.com/3mparticlerespiratorn95series8000.html
 
Having carved wood since I was 12yo I have found that the 3M makes a wonderful mask for light dust/pollen situations. I forget the number but they are avilable from HD and Lowes...they are normal fitted dust masks with a fine rubber mesh that covers the entire mask. Mine do not have the metal nose strip but they fit very comfortably including outside in 80+ degree weather....the filter itself is made up of multiple layers and has a very fine moleskin type material on the inside....they last a long time and are pretty cheap...they come in packs of 5.
 
Very good information and it is appreciated. After doing all the reading I will take a look at some masks and make a decision. I will probably go for something which fits the face better than the disposable ones. Thanks again, Dan
 
Hey Dan,

As a life-long asthmatic, I can agree without hesitation that your doctor needs to give advice on this.

I use either the disposable ones with thick fabric, foam nose fitting strip, and air exhaust in the center; or a soft rubber painters mask with the replaceable filter cartridges.

Air conditions and how much dust I'll be stirring up determines which I wear. And both types of masks will restrict your air flow, in other words, you'll have to work harder to breathe while working.

The challenge with the fancy ones, (between $29 and $40), is that the soft rubber face piece is hotter n heck in the summer.

You will also probably have to experiment with different activities, and see how your energy level responds. On hot, high-dust days, I'm only good for a few hours outside, whether I'm riding the mower or working on the ground...I just don't have the stamina I used to!

If you're like me, the most frustrating thing will be when the doctor says not to overdo it...it'll drive you nuts, but just take it easy and you'll get a handle on what you can do...and keep smiling...you'll do fine!

Corky
 
Corky: I have been wondering about the degree to which a mask restricts air flow. I would imagine that masks which are less restrictive are also less effective in filtering smaller particles. So I may have to try several models to find one which works well for me. At this time, I really don't know the degree of protection which I will need. Before starting chemo I would work without a mask and would rarely need to cough to clear air passageways. Today, a small amount of dust brings about a coughing reaction. We had some wind yesterday. I was outside for 10-15 minutes putting a tarp on Barnyard's Cub and I did quite a bit of coughing from that small exposure to dust. My last chemo treatment (assuming that all cancer cells are destroyed by the current series of treatments) will occur on March 17 and I expect that I will then begin to become less sensitive to dust over a period of a few months. But I think that I should use a mask when working in a dusty environment and certainly need one when wire brushing metal parts to remove rust. All of the posts in this thread are good and will help in selecting a mask which works for me. Dan
 
My grandfather used a bandanna soaked in water. At the end of each row he would rinse it in the bucket of water on the tractor. He said it worked very well.
 
as for dispoable the N95 is the only 1 worth your time. All of the other disposables give very little to no protection from anything. They just give the poor user that is wearing it a warm fuzzy feeling, while providing no protection. I could give a long lecture with many test resulsts but, you would give up reading after 5 minutes.
 
My main need for a mask is to filter dust when working outside and also to control rust particles when cleaning parts with wire brush on a side-angle grinder. What little painting I do is from a rattlecan. Would I be looking at two masks, one for dust and rust and a second type to use when painting? If so, what type of mask for painting since I wouldn't be using a hardener? Dan
 
I purchased a package of masks yesterday. Made by Willson, NOSH N95 rating. I paid between four and five dollars for the pack of two. Much thicker construction than some of the cheaper units. I won't know how effective they are until I actually use them. After fitting them to my face and covering the mask with my hands, it pops inward and outward when inhaling and exhaling so I believe that it must be sealing fairly well. I will give these a try when working around dust or rust and plan to buy a more expensive one to use when painting, rattle can only. Thanks for the good advice. Dan
 
Dan, you need a cartridge filter mask, with activated charcoal cartridges for organic vapor removal for painting.

I'd use a paper filter mask a heck of alot more often if I could only figure out how to keep my glasses from fogging up while I'm wearing both. Has anyone worked out a method? It seems like I almost have to decide whether I wish to protect my eyes, or my lungs. But not both. I'd appreciate some suggestions . . .
 
Paul: It will be some time before I attempt to paint. So I am taking more time and trying to get more information on what to use when painting. And I do appreciate your input. Sorry I can't help on the problem of fogging glasses. I have sleep apnea, need to use C-Flex machine to increase oxygen intake during the night. I wake up 3-7 times each night. If I read for a few minutes I go back to sleep. If not, I may be awake an hour or more. I have tried different masks for night use but each one tends to fog my glasses. Too often, I choose to remove the mask, read a few minutes and sleep rather than laying awake and getting the proper amount of oxygen. It is a problem with masks. Dan
 
Paul_NJ":rie0w4wy said:
Dan, you need a cartridge filter mask, with activated charcoal cartridges for organic vapor removal for painting.

I'd use a paper filter mask a heck of alot more often if I could only figure out how to keep my glasses from fogging up while I'm wearing both. Has anyone worked out a method? It seems like I almost have to decide whether I wish to protect my eyes, or my lungs. But not both. I'd appreciate some suggestions . . .


Paul, not sure if this will work on all glasses but I clean my lens with vinegar and seems to work fine for me. Don't see any better but they don't fog up. Grump
 
Back
Top