Trailer wiring mystery

Gary Dotson

501 Club
I'm confused! I bought a 2015 Silverado, with factory towing package and installed my brake controller. The factory supplied pigtail was still in the glove box, unused. Anyway, when I finished, I got out my handy, dandy LED tester and plugged it in. Nothing, no 12v., no lights and no brakes. Using a test light, grounded to the bumper, I had power everywhere it was supposed to be. At this point, I'm assuming a ground issue with the connector so I removed it for examination. The ground was good so I looked for a connection issue and found none. I can probe, with the test light, inside the connector, using the ground pin, and everything tests normal. The only issue is that this silly little plug in tester, that works perfectly on both of my other vehicles, doesn't work at all on this one. When the ground firms up, I'll connect to my trailer, I'm pretty sure everything will work right. While it's not a big deal, this thing is bugging the heck out of me, anybody got a clue?
 
some newer vehicles the function is computer controlled, and may have to have it activated by the dealer
 
I considered the polarity issue and checked it, no difference there. The bumper is well grounded (just like the owner) It got firm enough, this afternoon, to drive out back and check, with the trailer connected (but not hooked up, just plugged in the pigtail) As I suspected, everything works perfectly (except that stupid little tester). I'm hoping more people have some thoughts, on this because it makes no sense to me. I don't have a problem, it works just fine but I do have a mystery. All thoughts are welcome.
 
Have you verified that the LED tester works on one of your other vehicles after it didn't on this one? I'm grasping at straws here.
 
Gary, being the electrical wizard you are, I can understand you wanting to solve the mystery. But, some things you just need to accept they work, kinda like a thermos..... Keeps the hot things hot and the cold things cold, how does it know??
 
Checked all that, John, I even put on a new connector on the off chance that I was losing ground through the connector. As I said earlier, the trailer lights and brakes work fine, just not the tester. Yes, Jim, I tried it again on both the Traverse and motorhome, works fine on either. Yes, David, I understand that some things in life remain a mystery, but I'm having a hard time letting go of this one. It just seems too obvious, it should work. Maybe, my newly acquired pick up has some sort of top secret, proto type electricity. That makes about as much sense as anything else I've come up with.
 
put some thin strips of aluminum foil on the pins to locate the problem pin. Something tells me its a fitment issue and when you plug it in it shifts one pin alittle and breaks contact.

I have faith in you Gary, you'll discover whats wrong.
 
I'm thinking down a path similar to what Rick said. There may be some minor production flaws or detail design difference in both the Silverado socket and the LED tester plug that makes them incompatible. For example, it could be something like a slightly short contact combined with a shoulder on one piece that prevents a full depth engagement. Since none of the LEDs lights, it seems likely to be a problem with the ground contact between the two parts.

I suppose you have already tried plugging the tester in, turning on something that should light it, then pushing in hard on the tester while wiggling it in various directions to see if you get a blink.
 
Gary, The missing ground I am referring to would be the truck connector, not the extension. I ran into that on my Ford Ranger, what should be the ground on the factory plug was blank, the ground had to dome from an external lead in the extension. The reason I came across that was The external lead in my extension was connected to a bolt that had become rusty. I spent about half a day chasing that.
 
Gary. Take me back to the brake control. Does it light up with nothing hooked up. I have a2011 Silverado that when the trailer is not hooked up the lite on the control does not lite up. Maybe your connector needs more amp draw restriction to make led tester work.
Just shooting in the dark.
 
Back
Top