Toro Workmaster

ScottyD'sdad

501 Club
I was given an old Toro Workmaster , 3 wheeled utility cart. Kohler K321S, 14 HP engine Hydrostatic tranny. Can't seem to locate any info on it. I have a picture, but am too computer illiterate to post it. Correction, it did post!, twice! Any info on it, would be appreciated. Don't know where to find the ID plate, for numbers. I'd like to restore it to use for gardening chores.
Thanks,

Ed
 

Attachments

  • 00Q0Q_9PAOLhzJ3tW_1200x900.jpg
    00Q0Q_9PAOLhzJ3tW_1200x900.jpg
    177 KB · Views: 3,230
  • 00Q0Q_9PAOLhzJ3tW_1200x900.jpg
    00Q0Q_9PAOLhzJ3tW_1200x900.jpg
    177 KB · Views: 3,231
I've seen a few posts on the Red Square Wheel Horse forum about them. Personally, I don't know much about them - they seem to be Toro's version of Deere's AMT (all materials transport)
 
Acreage neighbor has owned one for 20 years. Neighbor used the machine as mobility for the now deceased handicapped father.

Next time I see the neighbor, I will take a closer look at the machine.
 
T-Mo":dj88nhed said:
I've seen a few posts on the Red Square Wheel Horse forum about them. Personally, I don't know much about them - they seem to be Toro's version of Deere's AMT (all materials transport)
I did a search on that site, but didn't find anything.
Ed
 
Eugene":eae5hz7p said:
Acreage neighbor has owned one for 20 years. Neighbor used the machine as mobility for the now deceased handicapped father.

Next time I see the neighbor, I will take a closer look at the machine.
I found the ser # plate, today. Manual Don sent me seems to cover it. Thanks.
Ed
 
Don McCombs":2652o624 said:
Do you have that thing running yet, Eddie?
Not even unloaded from the trailer. It's about 5th on the list, for getting fixed. Got it because it was available, not becaiuse I needed it immediately. Hope to have it running, for gardening season.

Ed
 
Toro made a lot of "Masters" I have a "park" master. bit bigger than yours but I like it, someday it may sport a bed like yours. ( only bigger ;) ) is yours a power dumpbed? I found a few pictures of workmasters but most are newer with more streamlined fiberglass bodies.
 
Indy4570":25aqy4vw said:
Toro made a lot of "Masters" I have a "park" master. bit bigger than yours but I like it, someday it may sport a bed like yours. ( only bigger ;) ) is yours a power dumpbed? I found a few pictures of workmasters but most are newer with more streamlined fiberglass bodies.
Doesn't have a dump body. It may have one, in time. Sure would be handy to have it dump.

Ed
 
That is nifty, and looks like Cub front rims on the back. Hard to see on my phone.

That thing will scoot with a hydro transmission and 14 hp.
 
Progress report. Grandson helped me get it into the basement, on Sunday. Body is off, and I've started to free up rusted components. Left rear brake was rusted to the drum. Got the drum pulled off, so i can clean up the brake shoes. Hydraulic brake lines will need replacing. Parking brake cables, are rusted tight. Might use a gallon of Kroil on this project.
Can't believe how ruggedly built this is.
Ed
 
ScottyD'sdad":3anj64z1 said:
...Not even unloaded from the trailer. It's about 5th on the list, for getting fixed. Ed

Does this mean you've got the other four (higher priority) items done on your list? :lol:

Seriously, now that you can attach photos, give us some updates along the way. We'd like to see what you're doing... :coffee:
 
That photo was copied from the Craigs List ad. I can't attach my photos. I'm electronically challenged.
2 projects in the garage, mostly done. Too cold out there to work, so I'm in the basement, where I can work with one arm, hug the wood stove with the other.
Ed
 
Toro update..... Trying to start the engine, just bypassing the wiring and fuel system, using carb cleaner or starting fluid, to see if I can get even a 2 minute run, out of it. Has good compression. Wasn't getting a spark. Changed the coil, points and condenser, and now get a good spark. Acts like it's out oif time. Only timing adjustment, is point gap. Adjusting them, doesn't make much difference. Someone suggested flywheel key. It's hydrostatic, so I doubt that the engine received enough stress to bend the flywheel key. 14 HP Kohler engine, 1970's era. Any suggestions would be welcome. It's stressing my limited sanity!

Ed
 
well have you checked the spark timing while the engine is on the compression stroke? like you know, plug out and your finger in the hole? one thing that has been an issue for me before is just a chunk of carbon, blocked valve from closing, so no compression. I would pull the head n inspect things.

been working on my Toro ParkMaster. got a replacement transmission and got it to fire but carb is still messed up, wish you luck with your Toro, hope to see it running around soon!
 
Seems to be a compression release issue.. Head is off, valves open and close properly. No exhaust valve movement, to release compression. I think the compression release has a broken tab. Have another camshaft on order. Didn't want to get that far into the engine, but, it won't run the way it is. My guess is that it wouldn't start, and was given up for dead.

Ed
 
Back
Top