Tillotson Carb YC7A Repair Help

This one got put on the back burner for a while. Got it apart and after a long soak finally got the needle/seat assembly out. The immediate problem is to find a way to repair the "posts" that hold the float axle in place. The metal ends are completely deteroated. (Pictures to follow.) The quick fix would to be replace the top but that's not likely given that's its obsolete. Any suggestions are appreciated. Thanks. Stan
EDIT: If you want to see the entire thread go to page 2 and look for this thread from January 26, 2024. https://farmallcub.com/community/threads/tillotson-yc6a-carbuerator.116221/
 
This one got put on the back burner for a while. Got it apart and after a long soak finally got the needle/seat assembly out. The immediate problem is to find a way to repair the "posts" that hold the float axle in place. The metal ends are completely deteroated. (Pictures to follow.) The quick fix would to be replace the top but that's not likely given that's its obsolete. Any suggestions are appreciated. Thanks. Stan
EDIT: If you want to see the entire thread go to page 2 and look for this thread from January 26, 2024. https://farmallcub.com/community/threads/tillotson-yc6a-carbuerator.116221/
That is going to be a tough repair. May be easier to modify the linkages on a similar carb. Also some more pics at different angles may help track down something similar.
 
Thanks Don. I've already been in touch with Bob on this one. If JB Weld will hold up in the gasoline environment I might be able to do something with that. It will take some time to get it done. The fuel control is missing some parts of the ball valve assembly. It's not a needle and seat type. Stan

EDIT: Correction to the needle and seat statement. I do not have a parts list for the YC7A, but checking the parts manual for the YC6A shows a conventional needle and seat. When I checked the YC6A, I found a caged ball that is operated by the flat lever attachment to the float. It raises the ball inside the cage when the float goes up. The YC6A parts list shows a std needle valve and seat that screws into the top half of the carb and the YC7A appears to work the same way. It AVERY-MM part number *06287. The * identifies parts in Repair Kit 07916. Sorry for the misinformation. CRS has kicked in again. Stan
 
Last edited:
As promised are pictures of the broken/deteoriated posts. The entire mounting fits inside the lower half and the only additional space is on the side toward the center. Just enough space between the brass fitting and the web/post mounting are to get a thin wall 7/16 socket in to remove the fitting.
 

Attachments

  • Til YC7A 1.jpg
    Til YC7A 1.jpg
    257.7 KB · Views: 12
  • Til YC7A 2.jpg
    Til YC7A 2.jpg
    250.2 KB · Views: 12
  • Til YC7A 3.jpg
    Til YC7A 3.jpg
    295.1 KB · Views: 12
Update on repair: found and purchased a parts YC5A carb on ebay. Hopefully this will provide some help to resolve this problem (if it fits). Lacking a detailed parts cross reference I can only try it to see if it works. Stan
EDIT: YC5A carb arrived, initial inspection looks to be the same housing and in much better physical condition. (The float, shaft and mounting attachment posts are identical.) After further cleanup and examination will determine if the YC7A carb can be a parts donor and possibly salvaged at a later date.
Edit 2: Cleaned up nicely, but big surprise, the YC5A carb will mount directly to the manifold same as the OEM YC6A and IH but the throttle "butterfly" (parts manual calls it a shutter) is smaller than the YC7A. All other internal parts appear to be the same. McDonald Carb is sending the correct shutter and with donor parts from the YC7A to connect it to the governor, it should return this one to service. Long term I still think I can salvage the top from the YC7A (pics above). If I can repair it then someone can use it. I'm continuing to pursue this because they are obsolete and someone, somewhere is probably looking for one. Stan
 
Last edited:
Back
Top