Things that don't work

I know everyone has tried to do something that didn't work out as planned, how about posting some of them here. Humorous is good. I'll start off.

Never run a large weed wacker or chain saw for seveeral minutes and try to weld immediatley afterward. Took both hands to hold the stinger steady enough to run a bead.
 
Overhauled the engine on a 36 WC Allis Chalmers owned by my grandfather. Got the engine running, oil leaks stopped. Put 3 or 4 gallons of gas in the tank. Took the tractor out for a run. Out the shop, down the hill, around the bottom, back up the hill, engine looses power and dies. Coasted back down the slope. Checked the fuel - plenty. Waited, the engine started and ran great. Back up the slope, engine dies. Drag the tractor back to the shop. Swap magnetos. Trial run - same thing. Back in the shop, checked the engine timing and valve settings. Another trial run - same thing. Rebuilt the carburator, added an inline fuel filter. Trial run - same thing. This time I stop on the slope and look in the fuel tank. Lots of fuel in the back of the tank.

Then it dawns on me. The fuel tank outlet is on the uphill side. I've been runnning out of gas.

Eugene
 
I have been re-painting our kitchen. The window behind the sink has areas where 3 different colors of paint come together. (wall, ceiling and trim colors) and it is in a very confined area. I had removed an old light fixture and have a new one to replace it with. While painting I accidentally brushed against one of the two wires hanging loose only to find out that whoever installed the light originally had the foresight to switch the neutral wire rather than the hot so guess what! Ol' Bigdog gets a nice electrical shock! I discovered that it is rather difficult to edge freehand immediately after receiving an electrical shock of significant proportion! Seemed like a good time to take a break so the muscles could relax and stop twitching......... :shock: :shock: :shock:
 
Off Topic on class reunions on an Allis Chalmers site. I posted the following:

Well, I went to one reunion. Drove my beat up, unwashed, raggdy, farm/work truck with ladder rack on top, gas cans and tools in the back and parked in the front row next to the entrance. Parked next to the rental cars and high priced toys of self proclaimed rich.

Na, I could have taken the Cadillac. I just wanted to make a statement.

Eugene
 
to go with johns welding thing....

never weld without a shirt

my dad had a sunburn on his stomach. there was a line where the helmet was and then a crease in his gut where he was bending over
it was very funny
 
I had my 48 Cub all painted up and put back together. Just doing some final things to finish her up for Cubarama. She was beautiful! Then when I was standing there with the CLUTCH pedal in hand trying to figure out how it got installed, it hit me what I had done, ouch! :oops: :oops:
 
:oops: :oops: Changed the oil in an old car I had and noticed a little oil dripping from around hole in the bottom of the bell housing. With the car still running I took a rag slid under the car, put the end of the rag around my finger than stuck my finger up the hole to wipe out the oil. There's a flywheel in there with teeth on it. Took about a quarter inch off the end of my finger. The Doc was able to put it back on but to this day I have no feeling in the end of it. Not too smart! TIP- Never stick your finger in a hole unless you know what's in there!
 
I don't think that I have ever owned a vehicle that I couldn't get stuck. I always push the envelope for some reason. I was driving the tractor on the overflow end of the pond late one year just to, well I don't remember what I was there for. It couldn't have been too important. Well I got it stuck down to the axles. I believe I was into my cups a little too much so I decided to quit and get it out the following day. The ground froze that night and it was stuck. I tried jacking it out, pulling with another tractor. Nothing could budge it. We had a cold winter that year and it was several weeks later before I could pull it out. I just threw a blanket over him and we waited it out. I forgot how I actually got it out. The spring daisys probably pushed him out. That was a particularly long, hard winter for me.
Larry
 
Brent Duxbury":13acl7c6 said:
:oops: :oops: Changed the oil in an old car I had and noticed a little oil dripping from around hole in the bottom of the bell housing. With the car still running I took a rag slid under the car, put the end of the rag around my finger than stuck my finger up the hole to wipe out the oil. There's a flywheel in there with teeth on it. Took about a quarter inch off the end of my finger. The Doc was able to put it back on but to this day I have no feeling in the end of it. Not too smart! TIP- Never stick your finger in a hole unless you know what's in there!

This wasn't me that did this, but I still laugh when I think of it. Two heating guys are on the opposite sides of a partition. They need a hole for a gas line or something. After one guy drills the hole, both look in and see that there are a few chips inside the hole. One guy sticks his finger in to remove them... the other runs the drill back in. The first guy became a bartender! :shock:
 
Its a well known fact that I can't hit anything with my .22 ...

Saturday evening there were some large havelinas hanging around here. I grabbed my 22 to fire off a shot at about 100 yards... just to scare them away. Plop...200 lb. dead havelina up on the west side of our property :shock: :shock:

What do I do with a 200 lb. dead havelina. Guess I'll let him sun dry :roll:
 
Mike:

Pray tell, what in tarnation is a havelina????

Oh, must be an Arizona possum :!: :roll: :lol: :lol:
 
Rudi:

javelina.jpg
 
I bought a 18ft fiberglass boat years ago. Wanted to take everyone out on it the first time, I think my wife and three of the 5 kids were there for the first "fun" spin in the Ohio River putting in at Forked Run State Park.

Backed her down the launch ramp...unhooked and had her tied up to the dock.....went up and parked the truck and trailer....walk back down-hook up the battery....hook up the gas line...get the O/B motor purring.....then I see there's water splashing around OVER the top of the transom....hmmmmmm....don't remember that on the couple of tune-up runs in the lake right after I got it.....I lift the skirt up at the back of the boat where the gas tanks go...WATER !!!! EVERYWHERE !!!!...then it dawns on me.....you know the feeling...a combonation of impending doom and 'I can't believe I was so &*%^#@*&^%$#(*&^%#$ STUPID !!! HA ! On the way down, it rained like cats and dogs thru Mansfield OH, and when we stopped for a bite to eat, I removed the drain plug so the water would run out till we got to the river. Some dumb--- forgot !!! So, I jump outta the boat hollering to everyone else 'STAY OUT OF THE BOAT' !....run back up to the truck...race back to the ramp...back down...get the trailer under the boat any which way it was....I didn't care.....get back in the truck...drop it into 1st....by the time I had the drain hole out of the water I need two new tires for the rear(limited slip axle thank God)....it took 38 minutes for the water to stop coming out of the hole!!!!! put the drain plug back in.....back down the ramp...float the boat to the right spot on the trailer....back to the cabin cause now it's too late in the evening to go on the little joy ride I had planned......had a successful time in the boat the following day!....I will never forget that one !! :oops: :oops:
 
I’m going to call this story; “You can use Cub engine valve springs in other places other than the engine”
This happened to me about four years ago when I put a clutch in my first Cub I rebuilt.

It was about ten o’clock on a Saturday night and I got some time to put the clutch in my tractor that I was rebuilding. It was late and I was tired but, I wanted to get this tractor together to start prepping for painting. I bolted the pressure plate and disk into place than opened the box of the throw- out bearing and there was a note in it that was hand written which stated “this part is slightly different than original, but it will work”. The only thing I noticed was it was made with a little offset, but I thought the clutch adjustment should take care of that. I put the bearing in the throw- out bearing fork and bolted it back together and it fit pretty tight and I remember thinking “ the bearing won’t flop down and catch the transmission input shaft when I put the tractor halves back together, good deal”.

Well late that night I got it together and even started the Cub and drove it. I remember I was so excided that I got my tractor running after going to bed I couldn’t go to sleep.

After the Cub was finished one of my son’s was driving it around and said “he thought the clutch was making noise”. I checked it and sure enough there was some noise, but I pushed the clutch pedal down and release it and it went away. I shrugged my shoulders and said “it must be nothing”.

A couple of weeks later my dad was cutting the grass with the Cub and he stopped for a break and he noticed a noise coming from the bell housing area. I checked it out and noticed the throw- out bearing face popping against the clutch pressure plate fingers. I remember, laying on my back in the grass looking through the inspection hole wondering “what the heck is going on”. Than I noticed, the throw-out bearing center (inner dimension) was bigger than the original bearing and the center of the bearing was not resting on the transmission input shaft collar housing. After using the clutch the tension where the throw-out bearing slipped into the clutch fork wore in and the throw-out bearing flopped against the clutch pressure plate fingers and was popping back and forth when the engine was running. My stomach felt like it went to my throat. I was thinking how stupid I was not checking the new part against the old. The only thing I knew to do was to split the tractor and put the correct throw-out bearing in.

After thinking about it for awhile this is how I resolved my issue. http://img.photobucket.com/albums/v688/Jackf/100_0690.jpg I tie strapped a Cub engine valve spring into place to hold the throw-out bearing so it would not hit the pressure plate fingers when the clutch pedal was in the release position. It’s been four years “down the road” and the bearing is still working fine.

It didn’t come out the way it should have, but its working.

Jack Fowler
 
A nice work of engineuity(Sp) Jack. What impressed me more though was how you were able to get such a nice clear picture of the TOB through the inspection hole. :lol:
 
:oops: :oops: :oops:


Just got home from work and the truck was low on oil. Only oil left was some low ash oil for the cub. Poured in about a quart looking at thinking boy this strait 30# looks thick compared to 10-30. Set the jug down and saw it was marked #90 gear lube. Put in some MM to thin it out hope it does not blow up before sunday when I have time to change it. The fun never stops.
 
Iowa, December, about 40 years ago I owned a 59 Edsel Ranger. The Edsel was my only transportation. I was single and dating at the time. I purchased a 6-pack of malt liquor and set in on the passenger side floor. Hours later I took the 6-pack into the house to find several cans had frozen and burst. All winter long, once the interior warmed, the car smelled like very old stale beer. One nice warm spring day I had mushrooms growing out of the carpet. True story. That car must have been a real treat for my dates.

Eugene
 
Back
Top