Storing welding rods

midmo

Well-known member
How do you store your welding rods? Heard of old refrigerators with a light bulb to keep them dry. I need something for not more than 20lbs. at a time. After 25 years in different storage sheds I now have wire with little flux left on them. Rods have went up the last 25 years and would like the new ones I buy last.
Ron in Mid Missouri
 
My father in law keeps them in a cabinet inside the house above the stove. Not sure the above the stove part makes much difference, just may be where he had the space, but it probably helps. I might be inclined to keep them inside, but lots of folks know more about welding than me and I may be wrong.


Dave
 
Anything you can do to keep them dry is the most important. If they happen to get damp, and the flux is not falling off, then you can build yourself a small cabinet with a light bulb to dry them before use. Welding rod prices have skyrocketed in the last several years.
Attempting to weld with damp rods is not the most fun thing to do!!
 
I store my welding rods in plastic tubes with screw on caps. You can find the tubes in the same hardware section as the welding rods. I have 3 different tubes. One tube for each type rod - mixed sizes inside the same tube.
 
I keep mine in a 4in PVC pipe with cap on one end and a plug on the other end.
We have 70 to 90 percent humidity here and I have never had a problem.
 
For most welding electrodes E6010, E6011 and to a point E6013, I use the plastic containers that are made to store welding electrodes. I put in a desicant bag to absorb any access moisture. These bags can be found in most sporting goods sections.

The makeup of E6010 & E6011 electrodes flux (cellulose) allows for a normal handling and storage without much of a moisture problem. The tube storage works well for these electrodes

E6013 because of it's flux needs better handling and storage that make the plastic tubes and desicant bags a must. Remember that you have to replace the desicant bags regularly as well to keep your protection up.

E7018 absorbs moisture like a sponge and needs to be handled carefully or moisture will build up in the flux. The Reccomended procedure is storage in a "Rod Oven" at 200 degrees to keep the hydrogen (moisture) out of the rod flux. Rod Ovens are not cheap and have to always be plugged in.Again the good plastic tubes with a seal ring and plenty of desicant bags will work but be careful. I buy E7018 in 5 lb lots and leave it sealed in the bag until I need it. I then plan my job to use most if not all of it up then I do not have to worry about moisture during storage.

Like Eugene I store like rods in the same container for use.

Buy electrode from a reputable company, I have seen too many problems buying Rod by the pound from the odd lot store.

Also buy rod in quanties that you will use up in a short period of time or within a year. The 25 lb box may be a deal but if it takes 5 years to use it up, you will have a lot of problems storing it for that long. It is not worth the headache. Most welding jobs can be planned and the supplies can be purchased accordingly. I only have about 35 lbs spread out around 6 rods that I keep on hand. If you are fortunate to be close to Welding supplies like I am it is a good way to go.

Thats my .02

Mark
 
:oops: :oops: :oops: I had a senior moment not too long ago and put about a half dozen in the microwave to dry them out. We all know metal and microwaves don't go togeather.
 
Brent":3pex41r9 said:
:oops: :oops: :oops: I had a senior moment not too long ago and put about a half dozen in the microwave to dry them out. We all know metal and microwaves don't go togeather.

Brent,

how does Mamma like her new microwave? :) :)

Bill
 
Brent":2cp3if4p said:
:oops: :oops: :oops: I had a senior moment not too long ago and put about a half dozen in the microwave to dry them out. We all know metal and microwaves don't go togeather.

Brent,
Its OK to put them in the micro wave oven on the 4th of July.
 
Ron:

I am a newbie to the mysterious art of welding, but I did learn from my Father-in-law. One of the things he taught me is to keep the rods dry and free of moisture. He normally kept them in the house as he had nothing to seal them with. About 8 years ago I found some of these plastic o-ring equipped rod holders at Princess Auto. I bought him 3 and I then bought a few for myself. I am relieved to know that it wasn't one of the dumber ideas I have had over the years..

I normally use a hot box (a styro-foam box with a low wattage bulb attached to a thermostat or what has been described as a homemade incubator for chicks) to keep my glues from freezing in the winter in my unheated shop. I would think that a hot box with say a 25 watt bulb may also be efficacious in keeping your welding rods dry. An old fridge would be over kill and possibly more expensive to run than a 10 lb box of rods would cost.
 
Rudi, to use the hot box type setup for welding rods, you do not need to worry about freezing, just moisture accumulation, so a 7 watt night light type bulb (not one of the new LED types, they do not produce enough heat) is sufficient for something the size of a large ice chest. As to the refrigerator, you do not run it, just put a 25 watt or so bulb in the bottom to control moisture.
P.S. as to the cost of rods, you might want to check on them. they have really come up in price.
 
John:

Yup, you is right... don't need to run the fridge, just the light :oops: :roll: :D ... so an old fridge if you got it could be employed. And yup, the hot box I use is to prevent freezing, but it would be useful to control humidity as rods don't realy freeze. This is what I use:

8089732.jpg


Welding Rod Keeper

This is a less expensive one, it is just a case, does not have the o-ring or a seal of any type to keep out moisture:
Case

Here are some prices for Welding Rods at Princess - they are comparable to Canox/Air Liquide and Miller.

6011 Rods - $11.99 for 5.3 lbs of rods. Not too bad at all.. prices are pretty stable for us up here. I really like the Welding Rod Keepers and get them when they are on sale. They come down in price to about half price.. $4.99. I like Princess... good stuff,.... good prices... good replacement policy :!: :D :{_}:
 
One thing to think about, if you have some old rods that the coating has deteriorated to the point of not being usable, do not throw them away. If you have a gap that is a little wide to fill in , knock the insulation off an old rod and use it as filler material, either by laying it in the gap, or holding it in your other hand and feeding it in while you are welding, as if you were brazing, etc.
 
I keep my boxes of rods in the basement about 4' off the ground, its very dry. I was taught to strike the arc on a piece of scrap first before welding to preheat the rod. Some guys use old toaster ovens if the rod will fit in it. I did build a rod oven that would keep the rods hot but still touchable. I still used the preheat rod method anyway. Thanks to connectikit i now have the blue storage tubes. One more trick is to keep the rod on the steel near where your welding too. It will heat the rod too. I did a lot of larger structural bed plate work. In the colder temps I would keep the preheated rod in a welding glove till i use it. This will keep it warm till your ready for it. A small amount will workout fine.

Using the touch preheat method I get a perfect weld right from the start.

BTW; I also have a welding temp chart too. I got it from lincoln. You turn the chart to see if a preheat of the steel is needed depending on the thickness and the colder temps outside. Its a good thing to have when welding in the cold temps. I use the torch and the temp sticks so i know when its the correct preheat.
 
Back
Top