Steel I beam sizing?

batty54

Well-known member
Anyone know how to size a steel I beam for a overhead hoist in a garage? I was thinking of putting a beam in my garage to hoist at most a engine or such probably 2000 lbs max. I looked for charts on line but could not come up with anything useful except dimensions of the beams themselves. I did talk to a local construction co. owner and he said a 16"-20" beam would be needed. The span is 24'6" it seemed like an overkill. I could put a jack in the center if I really needed to for something too heavy. I was hoping for a 12" beam max to keep some headroom. I do have 10'6" ceiling height but wanted to be able to use the height for the lift, if you add the depth of the beam trolley and chainfall the lift height drops quick.
 
Donny sounds like hes got the answer, In my old shop I had a 6in. by 3in. web. 1/4 in stock beam . 16 ft. long supprted on each end. Hung quite a few 250 Cummins on it for a good many years. Frank
 
I'll get some measurments tomorrow, just got in from fixing the well pump.
I'll get some pictures too. It's 20' long with a trolley that holds my manual chain hoist (it was free) and I don't really pick up real heavy things, so it works for me.

Ron
 
Thanks for the link. I see there is also a formula for a one end fixed and the other free beam. I was originally thinking of a beam hinged at one end which would be able to swing out when I needed it. It would be supported by an "A" frame type of contraption I was going to make.

I have a trolley and chain fall free, was the key there just waiting for a free beam no luck yet been a few years.
 
Well, I ain't no expert and it has been almost 32 years since I really played with those kinds of calculations. Used to use em everyday in my college Architectural Desing courses, but I don't even know if I could figure out which values to plug into where... :big say what:

So, by using the trusty ILAR philosophy and advice from friends.. I decided to use an 8"x16" I-Beam in my new pole barn. It is 30' 5-1/2" in overall length. You can see what is going on in the New Home For My Cubs thread.
 
Hey Batty,

I am a structural engineer if you want I'll size up the beam for you.
Let me know with a response here or PM. If you need an enineers seal for the town hall building dept. let me know. My friend is registered in MA and I am not. (yet!)

Chris Wallace

Also
We have a lot of wood I joists and wood beams that are weathered that we are getting rid of. Anyone need anything for a tractor barn or ag barn. Still good but weathered. Must pick up or work out shipping from North Kingstown Rhode Island.
 
Got your PM. Answer what I PM'd you and I can size it up in 2 minutes.
Do you need an engineer's seal for the building dept? Probably not but just checking.

Chris
 
That is when I do alot of building. I prefab the walls. Knocked down my 11 x 22 chicken coop one night and the next morning had a new building up with a 11 x 22 tractor bay. hehehe

W12 x 16 works fine I can email you the calcs for the steel yard.

Anyone else need something sized up or need design ideas feel free to PM me!!

Chris
 
If I were a bit closer me and the dog would be there with the trailer to take a load of that rotting junk of your hands. I plan on an addition this summer to hold the stuff in the barn so I can enlarge the shop.
 
Cecil!

I am heading up by you in a couple weeks to get Shotgun 13601 demonstrator tractor that I am buying from him. I could bring some beams and I joists along then. Let me know. Ed said he could keep them at his place in Rehoboth, too. Then you could bring them back after the Cubfest.

Chris
 
Chris if you could bring some it would be appreciated. I would really like a few sheets of the 3/4 in. plywood also. If not we can go the route of getting some to Ed and I will pick them up there. Even if you can't bring anything with you I'm only 3 miles off of I90 so stop and say hi.
 
Cecil,

My parents are from Weedsport (exit 40 on the New York State Thruway) and relatives are scattered about up your way. Believe me Kinderhook is one town I won't be just passing by. I'll be stopping in.
Could you mail me a sketch of the addition you want to put on and I'll see what I can get for you. :D You know those I joists we have work great as roof rafters and there very light and easy handle. Hope you and the wife have a nice Easter.

Chris
 
I'll try to get a drawing to you this week. Keep bugging me as there is a lot going on. I have to have Samantha done by ConnectiCubfest. She is a complete tear down and restoration. Plus taxes. Plus an ad for Red Power and on and on. But boy am I having fun. :D
 
Cecil,

Don't worry about me not bugging you. Ed is giving me a little pressure to see that you get what you need. Just a quick sketch with some dimensions will do.

Also,
I had a few requests to size out beams or double check sizing...will get to those over the weekend. Like Rudi's building that looks like a tank wouldn't knock it over. :jeep:
 
batty or anyone else with a similar question, just google up a gantry crane manufacturer and you get some quick and easy info from thier brochures.
john
 
Back
Top