Shark attack

moparado":2k692obk said:
Have your phone company run a detailed diagnostic test on your phone line. Make sure they give you the specs. on paper. Sometimes they can fix a noisy line just by tightening up loose connections, changing out an underground spliced cable or changing a printed circuit board at their central office.
-Ken

How can anyone have their phone company do such a thing?

All I was ever able to do was have them tell me I was too far out in the boondocks to be elgible for anything but dialup. Their only suggestion was for me to move closer to their switching station. :evil: I'm only 1.8 miles away. STUPID company! We got a divorce after 50 years and the cable company built a line so I could have a much better connection with Road Runner. Cable has my phone connection too as well as TV.

I still blame the problem on Judge Greene who broke up the old Bell system that wasn't broke. :(
 
I still blame the problem on Judge Greene who broke up the old Bell system that wasn't broke.

Come on George, We all know if it aint broke, it's the govts job to fix it :shock: :shock: :shock: Grump
 
George W., all,
the integrity of the phone line for a dialup is probably the number one critical factor - no surprise there. Number two in my book would be to disable all Windows Automatic Updates including AV software automatic updates. These updates unknowingly run in the background and can slow downloads to a snail's pace. As i mentioned MSN Explorer was the worst.
Number three would be to set the modem NOT to connect at the maximum negotiated connection rate with the ISP but the maximum connection rate WITHOUT data errors. The ISP and modem default settings are just about always set to negotiate the highest connection rate with the ISP data errors or not!
This is assuming the modem itself is not defective or a piece of junk. Also beware of internal modems especially Win-type modems who gobble up a lot of the PC's memory and processor resources. Thats why they are so cheap!
I use a desktop modem for several reasons; i can monitor what the modem is doing by the LED status lights, by turning the modem's power off, there's zero chance of some malicious nar-do-well remotely starting my PC and having his way with it if its in sleep or standby mode and most high quality desk top modems have their own on-board processors and memory, releiving your PC of these functions.

Out here in the boonies, i had phone problems just about every thunderstorm or heavy rain. I got to BS'ing with one of Ma Bell's repairman on one of these trouble calls. During this BS session he mentioned there was an old splice in the underground cable located on my property. I also convinced him to run a diagnostic on my phone line which ended up indicating several problems. He did this test from his truck and only took a minute or two! He later replaced a printed circuit board at the central office and i was able to connect at a higher rate.
But the rain problem persisted.

When the phone went out after a rain, i measured the central office's DC battery voltage at Tip and Ring (the red and green wires) which should be normally from 48 to 52 volts DC which was zero volts indicating and open circuit fault or a dampness-related short circuit fault which popped the DC breaker at the central office to my phone line. Take your pick!
Armed with this info and after numerous phone outages after heavy rains and numerous trouble calls, i finally demanded the problem be fixed once and for all or i'd sue the phone company if i couldn't make an emergency 911 call.
They replaced the cable a month or so later last Winter and i haven't had a problem since.

Years ago i worked for a well known petroleum pipeline company whose valves, booster pumps, etc. were remote controlled via a 600 baud modem through leased conditioned telco lines. When i verified a telemetry problem was telco related, talking to the phone company was usually like talking to a wall. I had to have hard technical data proving it was their problem and not ours to get em off their arse and fix their problem. I batted a thousand with these people.
In the absence of hard technical data, being persistent and proactive is the only way to get the phone company off their arses and do something. Normally they can easily run a diagnostic test which shows frequency roll-off, attenuation (data receive levels), signal/noise ratio, etc. in a matter of minutes... if they want to...demand it.
-Ken
 
whew! most of that is same as greek to me. i knew a lil bit about 'puters back when all was done from the dos prompt, my own programs were written by me in basic, and autocad revision 10 was still new. besides that minor shortcoming it is my better halfs 'puter and i don't monkey with her stuff.

the phone company was consulted. they felt the need to replace the little box on the side of the house where the wire comes out of the ground. the entire 'puter system underwent renewal the same week as this years cubfest. like george, i am within clear visual sight of town, but still too far away for high speed. something about being on the wrong side of a transformer. it is a half mile between houses along our road so no cable service would ever come this way. like i said in my previous post, a dish is my only means of high speed connection, and i would rather stay in the cub-a-year club than give them the gold.
 
phantom":2qsrbcb8 said:
the phone company was consulted. they felt the need to replace the little box on the side of the house where the wire comes out of the ground. the entire 'puter system underwent renewal the same week as this years cubfest. like george, i am within clear visual sight of town, but still too far away for high speed.

Actually, the phone company did me a favor and I didn't realize it at the time. I was never able to even talk to anyone who was remotely (pun intended) in solving the problem they were causing with their poor patched up and outdated system. AGB must be flopping in his grave. :(

We went to satelite for TV connection for a while and then went to cable once we found they were perfectly willing to build the necessary line. After I told AT&T to roll all their defective wires in a tight little ball so they could put it where the sun doesn't shine I got my high speed connection elsewhere. HARUMPH!

I was told by a telco service man that their line tests measured the line I was on all the way to the end and back. If I could have found the wires I could have fixed it myself with a pair of dikes and a little tape. I like this system much better anyway. The cable people care.
 
phantom wrote:
whew! most of that is same as greek to me.
Hi phantom,
After reading the comments here, i realize now some of the things i mentioned mighta been a little too technical. Because of the continuing comments by dialup users on this forum, my intent was truly to inform. I've worked in the modem industry for 15 years starting when 300 baud modems were 'state of the art' and the internet was years away! Broadband and satellite were just as far off.
In addition to designing the telco interfaces for dialup modems to work on domestic phone lines, i also had to deal with modems designed for foreign countries and get the design to pass some of their stringent regulatory tests. Japan was the worst!! I got to know phone systems real good so this stuff is second nature to me. I apologize if i've confused anyone here.
i knew a lil bit about 'puters back when all was done from the dos prompt, my own programs were written by me in basic,
The phone system as outdated and archaic as it is in most areas has more to do with simple electronics than computers and software.

I'm gonna geuss the 48 Volt battery might of confused some folks.
For anyone who has a basic understanding of electronics, here's very basically how a battery fits in with the two-wire Public phone system.
The audio portion of the phone signal is superimposed or rides on a DC loop current. The source of this DC voltage is a big old 48 Volt battery bank located in the central office(CO).
When the phone is ON-Hook meaning its just sitting there waiting for a call, there is no current (called loop current) from this battery flowing through the phone. Once a ring signal is sent to the phone from the CO (which by the way is normally a 20 Hz 90 Volt AC cadenced signal), the phone or modem detects this large AC voltage and closes a relay to complete the electrical DC path from the CO battery enabling a DC current to flow between the phone/modem and the CO. Once this relay closes the phone or modem is said to be OFF-hook. The CO senses that the phone/modem is OFF-Hook and starts superimosing audio signals on the DC loop current. If you put a DC voltmeter across the two wires coming into your house:
ON-Hook (or open circuit) DC voltage should read the battery voltage, normally anywhere from 48 to 52 Volts DC
OFF-Hook DC voltage (closed circuit) should read anywhere between a few volts DC to 8 or 9 volts depending on the phone/modem, the battery voltage, voltage drop across the line, etc.

Now a question for inquisitive, how does the phone system get two-way simultaneous audio data on just two wires?

Hope i didn't add more confusion!
-Ken
 
Back
Top