Saved one from the scrap yard.

Rodney51Cub":2rnfdxoo said:
Another year has gone by on the "money pit". Made a little progress, but again life gets in the way of the hobby. Only three more years until I can retire. Hopefully I will have it done by then.

DSCN1516.JPG

Rodney 8)
You think you have problems, look at this trainwreck I'm working on! It was purchased new in the early 60s by my great grandmother so my granddaddy would have a bigger tractor to keep her farm disked up after she put it in the soil bank. My dad was in the Army and granddaddy was spread pretty thin.....last time it ran was in the early 80s.

Al

17992055_1419460501410616_6174123271338697045_n.jpg23843328_1629531617070169_6465879680057282452_n.jpg
 
The only problem I have now is trying to find the time to work on it.

Mine was stuck bad also. It got bored .125" over. Head was replaced because it was cracked. Intake manifold was broken. A lot of new clutch and brake parts installed.

I think I have all needed parts except a PTO shield, fenders, wiring and battery. I just have to remember where I put them and how everything goes back together. Still a lot of cleaning and painting to do.

Rodney 8)
 
I stopped working on this 49 Ferguson TE20 because they were logging across the road and that much good oak was something I could not pass up so close to home. hauled it all on the lil trailer pulled by a JD gator HPX. There is much more wood than this pic shows, that pile is over 8 feet tall and 40 feet long.

I have the same problem, have to remember what goes where and where are those bolts? :lost: :shock:
 

Attachments

  • DSCF3134 F.jpg
    DSCF3134 F.jpg
    359.6 KB · Views: 1,808
  • DSCF3128 F.jpg
    DSCF3128 F.jpg
    275 KB · Views: 1,808
Haha, I have around 4 projects like that all at once and other "quicker" or "more important" projects keep getting bumped in front of them!
 
:lol: I got a look at a JD A once owned by a fellow I bought a horse drawn sickle bar mower from.
I couldn’t make heads or tails from it. Two cylinder and where the hell is the engine? Weird engine layout but there’s something about it I liked though and I’ve kinda wanted one since seeing it.
I’d doubt if I had a tractor apart that long I’d remember how to get it back together.
Your tractor is showing signs it’s going to be a work of art when it’s done!
Good luck with it.
Mike
 
Lt.Mike":265lsok7 said:
:lol: I got a look at a JD A once owned by a fellow I bought a horse drawn sickle bar mower from.
I couldn’t make heads or tails from it. Two cylinder and where the hell is the engine? Weird engine layout but there’s something about it I liked though and I’ve kinda wanted one since seeing it.
I’d doubt if I had a tractor apart that long I’d remember how to get it back together.
Your tractor is showing signs it’s going to be a work of art when it’s done!
Good luck with it.
Mike

Horizontal 2 cylinder tractors are a completely different animal for sure. The "block" is just the two cylinders and the engine crankcase and transmission case are one piece. The main gear that drives everything is actually outside of the main case, as is the 6th speed gears! And an octopus coming from the oil pump/filter housing to get oil where it needs to go inside the crankcase. Everything is big and over-engineered but I am amazed that they used the design as long as they did---it's basically 1900's technology.

We'll see if I can figure out how to get this one back together when it's time.

Al
 
Still in progress on the "Money Pit". Seems like when I had time to work on it the weather would not cooperate. Hope to have it done by next falls local show.

Rodney 8)
 

Attachments

  • DSCN1674.JPG
    DSCN1674.JPG
    236.5 KB · Views: 1,418
  • DSCN1683.JPG
    DSCN1683.JPG
    225.7 KB · Views: 1,418
It looks like its getting close. I have many projects just like this that go on for years or decades. The finish line is near.
 
DSCN1844.JPG
DSCN1843.JPG
The "Money Pit" is running and 99.9 % together. Took it to a local show and parade today. Drove it 9 miles to town and it ran fine. During the parade it decided to give me problems and did not make it the full route. Ended up being stuff in the fuel tank that was not suppose to be in there. Cleaned the fuel valve, readjusted the clutch and it ran fine the 9 miles back home. I am normally very careful about keeping my gas cans clean but I must have had an attack of oldman foolishness in trying to get the tractor ready.

Rodney :oops:
 
Looking good. I haven't read through this entire thread, but from the posts I have looked at, it looks to be an adventure of sorts. Great job.
 
Rodney, you’ve done a super job on the JD A. Glad it didn’t leave you stranded in town. A fine tractor for anyone’s collection!
 
Back
Top