Oil Consumption-94 Ranger

Dan England

501 Club
I bought a 94 Ford Ranger Pickup with the 4.0 engine a few months ago. It was bought new by a handicaped person in Waldo who put 79,000 miles on it, mostly driving around town at speeds less that 35 mph. On the rare occasions when he visited Magnolia (7 miles from Waldo) he would sometimes attain the breath-taking speed of 45 mph. The truck had rarely gotten above 50 mph before I bought it. I drive it at 55 mph, occasionally up to 65. It's oil consumption is terrible, perhaps a quart per 300-400 miles. It is not fouling plugs and there is no visible smoke. Since the PO rarely drove far enough and fast enough to warm the motor up it has been suggested that there is a sludge and carbon buildup in the engine and the following solutions have been suggested. 1. Add Seafoam through the intake port and/or 2. Add motor flush to the oil. I am interested in all comments regarding this problem. Thanks, Dan
 
I agree with the sea foam both in a vacumn port, and putting it in the oil. If it is a stick the PO may have dogged it a lot. I will check with a friend of mine who is a Ford mechanic the first of the week. I have an 01 with the 4.0 that I really like, but they are totally different engines.

There is a very good Ranger forum at http://www.therangerstation.com. I have been a memember there for several years.
 
Thanks, John. It has an automatic transmission. A bit more information on my situation. The PO bought a new 2006 Ranger and I bought his old one. He passed away about a month ago. No one in his family was interested in the new one so I bought it a couple of weeks ago. He bought it in June and had put 1986 miles on it. The 94 is for sale and I have had some contacts on it. I tell them up front about the oil usage. It is often a financial hardship for them to buy any vehicle, even one as old as this one. So, I am going to be sure that they understand that it has a real problem before they commit to purchase it. It would be nice if we found that it was a problem which can be cured at a reasonable price. But, we shall see. Thanks, Dan
 
Thanks, BD. I changed the PCV valve soon after buying the truck. It rattles when I shake it so I believe that it retains its function. However, a bit of oil drips out of it when it is removed. Dan
 
Dan England":gbm9b6wb said:
Thanks, BD. I changed the PCV valve soon after buying the truck. It rattles when I shake it so I believe that it retains its function. However, a bit of oil drips out of it when it is removed. Dan

Long ago I dealt with a Ford with that problem. The line from the carburetor was plugged so the PCV valve wasn't really in the circuit. Fortunately for me it was destroyed in an uninsured fire shortly after it turned 30K.

In spite of my vow to never again own a Ford product I've owned two since. :( I've escaped the clutches of that F-250 but I still have the 2003 F-450 that the Fun Mover rides on. I only hope to get another 5K from it and I won't care.
 
George: We checked the line from the carb to the PCV. It has good vacuum so the passageway is clear. Thanks for the suggestion. Dan
 
Sonny: There is no indication of oil leaks. Underside of vehicle is reasonably clean. No oil spots on carport floor beneath the vehicle. A local mechanic who was not familiar with the vehicle suggested two theories. A. Maybe vehicle sat for extended periods of time between use, allowing cylinder walls to become dry, causing metal to metal friction when started, resulting in excessive wear of rings and/or cylinder walls. But, except for one 6-8 week period when PO was sick, the truck was driven each week, usually every day. B. Because it was only driven in town and always at low speed, maybe motor never became hot enough to seat rings. He stated that he had known of one case similar to this vehicle in that it drank oil. The oil was drained, replaced with Castrol motor oil and driven pretty hard for a day or two. Apparently, this seated the rings and the vehicle would go 3000 miles with no measurable loss of oil. I haven't tried Castrol but have changed oil then taken one trip to Monroe, LA and a couple to Shreveport area. Probably between 200 and 300 miles per trip and the motor should have reached the temp. needed to seat the rings. Please continue to suggest possible cures. Dan
 
I'm thinking gunked up engine from short drives - engine not fully warmed up.

I'd try an engine flush that is added to the oil. Following the directions on the container. Then drive the vehicle normally for a while to see if things didn't improve. If not - one more engine flush.

After that, I'd try the Seafoam to the oil and gas.

I have removed an engine's valve cover(s) and roded out gunked up oil drain holes in head. I'd wait on that though.

Just my opinion.

Eugene
 
Eugene: This is an approach which my son and I were considering when I first posted this morning. I wanted to learn if there is any bad downside to using the engine flush. What about clogging tiny passages, oil pickup screen, etc?I know that it should dissolve the gunk from passageways but will it also free up fairly large particles which might, in turn, clog oil pathways? Or perhaps that is the reason for the second flush if needed? Dan
 
Dan:

I have use a product called Risolin (spelling) a couple of times with no problems. All I can say is that I have not had a problem.

I think you are on the right track.

Eugene
 
Bill: There is no smoke from the tailpipe, the exhaust seems to be free of smoke. This is puzzling to me as so much oil is used it would seem that there should be a liberal amount of smoke being released. Dan
 
I don't know, but suspect a working catalytic converter may burn off much of the oil smoke. It may have an unusually sooty exhaust pipe.

I also think the engine flush idea is worth a try. BG Products makes a good one. I think they may call it "engine purge." The history of that engine strongly suggests the problem is deposits and stuck rings.
 
Here would be another area, as Jim said the converter burning the oil,---ok,--could have the burned oil residue be restricting the exhaust flow creating higher back pressure in the engine? ---just a wild card, but might be worth checking! thanks; sonny
 
I posted your problem on the rangerstation.com, and got a reply to check the oils sendign unit on the right side of engine near the front. It seems a high pressure leak is not unusual. He said to look for oil on strter or on right side of enigne.
 
Jim: The exhaust pipe on the Ranger is similar to that of my Impala. Generally, I don't need to add oil to the Impala between scheduled changes. John, no evidence of defective oil sending unit, right side of engine is not oily. I do appreciate all info which has been posted on this topic. Our plan, at this moment, is to do an engine flush soon. I will check today to see if the quick oil change place in Magnolia has the equipment needed to do a reverse flush. If not, probably Texarkana, about an hours drive, would be the closest place to do one. We may do the flush, rather than going to Texarkana, and hope that we don't encounter a problem of gunk stopping up passageways. Has anyone who has done this encountered such a problem? Thanks, Dan
 
Back
Top