New Chimney

I am considering switching the heat in my shop from a pellet stove to a large wood burning stove. There are 2 reasons for this, 1st is to get more heat in the space 26 ft X 44 ft, second is I have a 10 acre wood lot so other than the labor the wood is free. I have several sections of stainless steel metalbestos chimney, and would still need to buy the through the wall and mounting kit. I use a set up like this in my house and it has worked fine for 20 years. The other choice is to put up a block chimney. Just looking at parts on line I still have to spend quite a few dollars to make the SS functionable. Just figured I would ask for some opinions.
 
Unless you like laying block, I would go stainless, since you already have some of the materials. Also a much less time consuming venture.
 
Joe:

I had a GSW 2100 chimney for the 1st 10 years and a Selkirk since. I have a chimney surround ensuring that it is kept an even temperature. Before the surround I did have issues with creosote buildup as my chimney is approximately 25 feet. I no longer have issues since the surround was constructed. I like my chimney a heck of a lot better than my Father-in-law's brick chimney. A heck of a lot less maintenance, less construction hassle and no temperature variances which is important in keeping the flue clear of creosote.

Go with the S/S .. you will be a lot happier and still many dollars richer. Even if you had to buy the whole shebang new it still would be about 1/2 the cost of a masonry chimney.
 
"Birdhouse"? No, farmhouse, but the stove is just supplimental. I'm usually overseas 6 to 8 weeks sometime between November and March and my wife doesn't use the stove as much as we do when I'm home.
 
Joe . use plan C , put in an oil furnace , :D only about $4 a gal, you need to do something with that moldy cash you have stashed anyhow :D
I have no experience with the SS and can not give you any good advice
Boss
 
You can make a thimble using a 24'' x 24'' piece of sheetmetal and run your pipe thru the center. I like using 12'' of clearance when i go thru a wall with a stove pipe. My old shop was done that way. I just made an outside bracket to support the elbow and chimney. With my old shop i ran a piece of 6'' pipe thru a clay pipe were it went thru the wall. I used all single wall pipe.

I used the s/s metalbestos in my old house since '79 and never had a problem. I was told to use the 8'' pipe for the chimney and the 6'' pipe for the styove this way i had plenty of draft on any windless night. To cut down on the cerosote i put a heat temp gauge on the chimney pipe(single wall that connects to the stove) and one on the stove. Using the damper in the pipe to control the heat that goes up the chimney so it doesn't make creosote yet the heat is more in the stove where it should be. I use the gauge on the stove to keep the stove at an even heat and use less wood rather than wasting wood by over feeding it all the time with no gauge. Save your back too, use less wood and have more heat with less creosote......

I just got my oil tank filled since february and we used 95 gallons till now. I'm well under a 275 gallon tank of oil per year now.

I figured even if i purchased firewood at $200 a cord for 5 cords its $1,000 to heat my house all winter as were the cost of oil would be around $2,500 to $3,000. I'd still be saving. I dio burn skids and pallets till it really gets cold too. Sometimes thats till dec with some years.

I been heating with wood since '79 and won't use anything else. My house is warmer plus its cheaper. Bill
 
How's the stainless flue work in a brick chimney? Wife and I hope to build a house soon. I want a real brick fireplace, with either a wood stove or an insert. Want supplemental heat and "ambiance." No one suggest gas logs....the house we are in now is heated exclusively with propane. I have given the gas co's enough of my money the last 5 years!! :evil:

Al
 
Al:

Way I see it from a) experience and b) a design perspective the solution is to build a chimney surround around the Stainless Steel chimney - with 2"x4" or 2"x6" , sheath with either OSB or plywood (plywood is probably better but more expensive). Construct either a concrete base or a re-inforced steel base for the masonary facade, install masonary ties as you progress with the chimney bricks. Pretty soon -- all done :D and you have a Stainless Steel chimney with a brick exterior and no one would ever know that you have new technology inside a classic style brick chimney :D
 
THanks Rudi....haven't thought about that approach. There is a lot about construction I don't know, even more that I don't even know that I don't know!

Al
 
Back
Top