need firewood?

Mr E":q74kaaqi said:
It would take about everyone on this forum with chain saws to keep that baby in wood. :lol: :lol:

Mr E; You right i ran 100cc 25lb chainsaws for most of my loggin life and the trick is to keep that baby in the wood cutting. Even with the smaller trees i would just put on the 16" bar and rip right thru them like they were butter. Nothing can match the bigger power heads, the real cutting starts at 85cc's and up.

I been wanting to add a wood processor to my new log splitter but the problem is the diameter of the trees varies. We just cut 50"+ trees from the saw mill a few years back and its impossible to use a processor with that diameter. I like the bob cat attachment too but as we can see its limited. To me it looks like a 20" diameter log would max it out. As anyone knows when it comes to the vee's / y's this is where the wood is inter grained much tougher and harder and these aren't an easy split even on the best log splitters. But my new one with the 5" x 24" cylinder what won't split it will cut thru it with no hesitation. I have the plans in my mind already on the hydraulics with the wood processor bar/chain and how to hydraulically operate it. Now i need to figure out the adjustable splitting knives to make up to 12 to maybe 16 pieces at one time. There are bigger processors out there but your talking 50k and up now. I think the upgrade on my log splitter to the 16hp castiron briggs along with the 28gpm two stage pump will give me enough hydraulic power to run the processor at the sametime. I think its very doable and affordable. I gave this project to my engineer son to play with and think about for a while. I usually don't think or plan i just cut steel and build it. But the kids will have to do the work now.

things to think about in building a firewood processor;

1. Hydraulics, cooling, keep it simple with very little restrictions that can cause heat. Its all about the flow so with the higher the GPM and size of the tubing and hoses matters. Plus the higher GPM oil filters too. Keeping the hydraulics clean is the most important thing after keeping the oil cool. These two can ruin a hydraulic system in a very short time. A big capacity oil tank that equals 1 gallon per 1 GPM of the pump. Thats 28 GPM so its at least a 28 gallon tank. Plus the oil in the system so your a tad over the minimum gallons of oil required thats a plus. Remember to use a large suction line too so the pump doesn't cavatate or strain when sucking the oil from the tank. Keep the oil level well above the pump too. If the oil level is below the pump this is were the cavatation can cause problems. One more problem with this much oil is preheating it in the cold weather. This can be done by the engines exhaust with a butterfly setup to turn it on and off after the oil is warm. You need to warm the tank up. I don't like running a cold hydraulic system.
2. The diameter of your splitting cylinder. Make it as big as possible this is were the splitting muscle comes from. The steel beam on the splitter needs to be big too. The more lbs per foot the better. Hydraulic power mulitiplied can bend steel beams if there not heavy enough. The beam needs gussets too so the beam can't arc or twist under pressure.
3. How are you going to load the log processing table? I was thinking about a log lifter on a big scale with a winch to pull the logs on to the lifter. Of course a hydraulic arm with a grapple would be ok to have too. Then we need a hydraulic chain driven log feeder to feed the logs into the processor from the table. Then we need a feeder so the log goes into the saw/splitter.
4. Design it portable so it can seperate to transport it. I figure the splitter can be seperated to transport. And the log table with cut off saw can go seperate on its own trailer.

I don't think its that hard to build one. Got steel???????? :lol: :lol: :lol: Bill
 
That just takes all the fun out of it!!!!!!! :twisted: :twisted: :twisted: :twisted: Kevin :{_}: :{_}:
 
Back
Top