Shadow_storm56
Active member
So one of my other older engines is a perkins t6.3544 that is moderately modified and around 38 years old I think. I posted alot about it on another fourm but just found another interesting thing about it that may explain other issues.
So this engine runs a water pump that loads it down alot at higher rev, runs it no problem with plenty of power and it cools itself just fine. Some hot to stand by on a hot day when it's blasting off heat lol. So now to the issue that it has and had even after new valve guides were put in, it likes to burn oil at higher rpm... usually once you cross 2000 rpm. Fun fact now that I have a synthetic high temp oil in it the amount of oil it burns is very tiny. Like almost nothing really and this engine runs really long days. So now to what I realized which is if I keep the oil level at just the tip of the dipstick, well below the full or low mark it burns basically like.... a cup oil in 20 hours. If I fill it to full it would burn down to the tip of the dipstick in that amount of time. I noticed long ago that the dipstick tube had been broken and welded back on so the tip may actually be the original position of the full mark so that's interesting. Oil pressure runs steady at 60 with the synthetic and sump temps are well within normal range.
So now to another really odd thing it does, if I start reving to the 22-2400 range which is max rpm for the pump it will randomly building sump pressure and pop out the dipstick and squirt out oil. But the crank vent is not plugged and not roaring out gasses at this point, some say maybe one of the rings starts to not be able to hold the pressure at this point and some of the gases blast down and displace the oil. I have not needed to rev it past 2100 this year yet to see if the oil level helps that too.
This is a really long post but I know some people would find this interesting, especially since this engine was turbo charged from new but when we got it the engine had been converted to naturally aspirated. This works fine unless I overload it and the my stack starts to glow, this only happened once when I was finding the engines limits. So people have said that my issues point to possible major engine issues like a cracked ring. Funny thing is theres no colored smoke, no reduction in power, it starts easy, runs clean and cool (unless I load it too much)
The last thing I wondered is my pump actually had to be put on upside down for the situation which is fine except it's a graphite seal that by design always drips. This water runs down by the fly wheel and the fly wheel sprays the water out the side, so it could be not burning oil at all and have a little rear main leak which the water washes it away without notice.
Literally this engine has 1 problem that has many possible causes and otherwise it sounds great and purrs like a kitten. So that's the story of another one of my machines, what do you think?
So this engine runs a water pump that loads it down alot at higher rev, runs it no problem with plenty of power and it cools itself just fine. Some hot to stand by on a hot day when it's blasting off heat lol. So now to the issue that it has and had even after new valve guides were put in, it likes to burn oil at higher rpm... usually once you cross 2000 rpm. Fun fact now that I have a synthetic high temp oil in it the amount of oil it burns is very tiny. Like almost nothing really and this engine runs really long days. So now to what I realized which is if I keep the oil level at just the tip of the dipstick, well below the full or low mark it burns basically like.... a cup oil in 20 hours. If I fill it to full it would burn down to the tip of the dipstick in that amount of time. I noticed long ago that the dipstick tube had been broken and welded back on so the tip may actually be the original position of the full mark so that's interesting. Oil pressure runs steady at 60 with the synthetic and sump temps are well within normal range.
So now to another really odd thing it does, if I start reving to the 22-2400 range which is max rpm for the pump it will randomly building sump pressure and pop out the dipstick and squirt out oil. But the crank vent is not plugged and not roaring out gasses at this point, some say maybe one of the rings starts to not be able to hold the pressure at this point and some of the gases blast down and displace the oil. I have not needed to rev it past 2100 this year yet to see if the oil level helps that too.
This is a really long post but I know some people would find this interesting, especially since this engine was turbo charged from new but when we got it the engine had been converted to naturally aspirated. This works fine unless I overload it and the my stack starts to glow, this only happened once when I was finding the engines limits. So people have said that my issues point to possible major engine issues like a cracked ring. Funny thing is theres no colored smoke, no reduction in power, it starts easy, runs clean and cool (unless I load it too much)
The last thing I wondered is my pump actually had to be put on upside down for the situation which is fine except it's a graphite seal that by design always drips. This water runs down by the fly wheel and the fly wheel sprays the water out the side, so it could be not burning oil at all and have a little rear main leak which the water washes it away without notice.
Literally this engine has 1 problem that has many possible causes and otherwise it sounds great and purrs like a kitten. So that's the story of another one of my machines, what do you think?