Motorcycle info??

perk

Well-known member
My son-in-law just bought a Honda CRF motorcycle which needs some work on it. Does anyone know of a website that we might go to to get some help on servicing motorcycles?
Now if that was a CUB I could help him. Was hoping to find some site like I found here for CUBS. I know it would be hard to find a site as well as the Cub site but.....
Thanks,
perk
 
Don't know of a website off hand, what is the problem, I may be able to help.
 
I dont know of a good Honda forum, or any manuals online. Except someone posted the other day about a site with all sorts of free manuals on it......... I will say I was a member of ktmtalk.com for a while, and they do help with other bikes. There is a section for Japanese bikes on there. You might try it, though I found a good many people to be jerks - pretty much why I left it. There ain't no place like here :D :D
 
Donny,
This cycle has sat for some time without being run. Took the carb off to clean. Cleaned out all jets and bowl and needle valve and now it seems to not be getting gas. It will fill the bowl after sitting a few seconds and run for a few seconds and then die.
 
Spiveyman, I knew it would be hard to come up with something as good as this Cub site
Thanks
 
With the fuel shut off, remove the fuel line from the carb and place the end of the line in a jar or something simular. Turn on the fuel and see what kind of flow is present. Not sure about the CRF but most motorcycle petcocks have a filter screen built into them. If the fuel just dribbles you'll have to remove the tank and drain the fuel from the filler. Once the tank is drained remove the petcock and see what's up.
 
Thanks Donny....will start there. Just hope we got all the parts back in the right places in the carb.
perk
 
I think you probably did, not too many places those parts will interchange.
 
perk":3cbs1ieo said:
Donny,
This cycle has sat for some time without being run. Took the carb off to clean. Cleaned out all jets and bowl and needle valve and now it seems to not be getting gas. It will fill the bowl after sitting a few seconds and run for a few seconds and then die.

Perk what year is the bike and size? Its a Motorcross bike yes? Years ago the Honda CR was a two stroke motorcross bike. I was a mechanic at a few shops back in the 80's, Honda, Suzuki, Yamaha , Husquvarne and Harley -Davidson.. I would recheck your float level and also check the jets the small one (pilot ) is your low speed idle , if that's plugged it will be hard to start and only run with throttle opened enough to draw gas thru the high speed jet. You can clean the jets with a solvent , air and a cutting torch tip cleaner or small drill bit just be careful that you do not make the jet bigger. Also get a new filter and plug and fresh gas.......... anyway its been a long long time for me and bikes but back in the day I did work on a lot of them so may be I can help ya...
 
Jackman,
It is a 2003 CRF 150F
I will make sure it is getting a full flow of gas to the carb. If it is then I will go back to the jets and float. The needle valve was in bad shape but I think I have it working good now.
Thanks,
perk
 
perk":3r34qrc9 said:
Jackman,
It is a 2003 CRF 150F
I will make sure it is getting a full flow of gas to the carb. If it is then I will go back to the jets and float. The needle valve was in bad shape but I think I have it working good now.
Thanks,
perk

that's a Thumper 4 stroke :o ,,, back in the day that would have been an XR..... The big XR's 250 and I think 500 was a bear to start even when brand spankin new.... Did ya see crfsonly.com , they have a site exclusive to CRF's bet they know what ails your bike....
 
My father always said : The first and most important "TOOL" to by when working on anything is : The Manual.
That being said , Clymer is an excelent choice. You could purchase a manual from the motorcycle manufacturer but usually they are written for experienced machanics. Clymer is much more detailed.

Just my .02 / Jerry
 
Hey...We got it! Donny you put me on the right track. There was gas getting to the carb but not a good full stream (I found out). After cleaning everything from the tank to the carb it now runs great.
Thank everyone for your help.
perk
 
We would clean the tank and take apart the carb on every used bike we got before trying to start it up it was the norm. Every used bike was sitting and most of the time the gas went bad. Clogged jets can be a real problem too. If they can't be cleaned you need to replace them. I'm good with the two strokes but not too familiar with the newer 4 stroke bikes, if the carb has a slide in it we put a little oil on the slide so its lubed and won't stick or wear out too. My son hasn't purchased a new 4 stroke bike to race with yet, but he is looking at them.
 
Back
Top