Model A won't run

Brent

501 Club
:roll: :roll: :roll:

A friend of mine and I are trying to get his model A running. Problem is it's hard to start and when it does start it runs for about five minutes than quits. We're running out of ideas. Here's what we have done so far:

-Gas tank cleaned
-Used lawnmower gas tank elevated above carb and ran line to carburetor, no filter
-Swapped carburetor for one from a running A
-Installed new plug wires
-New coil, points, distributor cap, rotor, plugs and condenser (twice)
-New Ignition switch
-Compression runs from 48 to 52 pounds

After all that it continues to run for 2 to 5 minutes than quit. We've pulled a plug after it quits, grounded it,turned it over and there's no spark. Wait a while and try again and we get spark but won't continue to run. Any ideas? One thought was that the generator is not working so battery can't supply enough juice to keep it going but I don't think that's it. I ran a 54 Ford for 300 miles on the battery before it quit when I turned the high beams on.
 
Brent":2xciflkj said:
After all that it continues to run for 2 to 5 minutes than quit. We've pulled a plug after it quits, grounded it,turned it over and there's no spark. Wait a while and try again and we get spark but won't continue to run. Any ideas?
No spark - faulty coil. Is this one of the buzz box, vibrating type coils?
 
No, it's a regular can coil but brand new. Acted the same with the old coil so I think we eliminated that.
 
Try this first. I'm assuming you hand crank start the A. Check the battery voltage - across the terminals - voltage drop test. No load and then with engine running. Ball park - a 6 volt battery - will operate (only) the ignition system at about 3 or 3 1/2 volts.

If not a faulty battery. Then the only thing I can suggest is to get into a no spark situation and start looking for the fault. Start checking for voltage at the points and continue working back to the battery until you locate voltage. Problem will be in the previous appliance or wire checked.
 
It's electric start. Maybe I'm wrong, but I would think that a fully charged battery would run it for more than a few minutes even if the generator is bad.
 
Compression is low which is one of the reasons why it's hard to start. Lousy compression may also be causing the stalling due to spark plug fouling.
 
Brent":domlag6u said:
It's electric start. Maybe I'm wrong, but I would think that a fully charged battery would run it for more than a few minutes even if the generator is bad.
If the battery, fully charged, will crank over and start the engine, the engine will run for many many hours without being further charge.

The no spark leads me to be believe it's an ignition problem. But could also be an electrical problem - ignition related. Such as an open caused by resistance - could be in a wire, switch or perhaps a junction/connection.

Compression. One reference says 60 psi as anticipated pressure for the 177 cu.in. 20 hp., model T engine. Any way, without further research, 48 to 50 psi may well be satisfactory for the engine.

Edit. Copied specs for the Ford Model A engine: Note the compression ratio.
Rated Horsepower: 24.03 SAE
Brake Horsepower: 40 HP
Compression Ratio: 4.22:1
Piston Displacement: 200.5 cu.in
Bore: 3.876"
Stroke: 4.250"
 
Eugene":3heso7ud said:
Copied specs for the Ford Model A engine: Note the compression ratio.
Rated Horsepower: 24.03 SAE
Brake Horsepower: 40 HP
Compression Ratio: 4.22:1
Piston Displacement: 200.5 cu.in
Bore: 3.876"
Stroke: 4.250"

The typical C60 compression ratio is estimated to be 5:1, that's why I believe 50 psi is a low in the Ford. I have a Cub engine with similar compression that only starts when 12V spins the starter and it doesn't run for long on a set of plugs before fouling. Something elst to consider - if valve lash is too tight, they will become leakier as the engine warms up.

Edit: Circa 1957, the optimal C60 compression ratio is actually 6.5:1 and 120 psi at cranking speed. So 50 psi in the Ford is adequate to start and run easily. For anyone who is interested, the high altitude Cub cylinder head provides 7.5:1 compression!
 
Discussing compression ratios. I have a 1936 WC Allis Chalmers that belonged to Grandpa. I know it was duel fuel from operating it as a kid.

I overhauled the engine. During overhaul I was rotating the engine and noticed that at the top of the piston stroke the piston was about 1 inch from the top of the cylinder. The compression is 70 psi at engine cranking speed.

Bit of research shows that the duel fuel/low grade fuel piston assembly in the WC could either be a compression ratio of 4.2 to 1 or a 4.5 to 1 ratio. 9 different piston sets were available for the 201 cubi Allis engine ranging from 4.2 to 6.6 to 1.
 
:D :D After replacing everything electrical it turned out to be the top plate in the distributor, the one the points are attached to, intermittently shorting against the distributor body. Can't figure out why but that was the problem.
 
When i worked at the dealership on new cars we had all kinds of problems like this. Ive seen the wires in the distributor crimped under the electronic ignition plate shorting out the ignition. Even on the customers cars one put the battery hookups backwards. The head mechanic had a pile of burned out diodes from the alternator when i walked over and told him to connect the battery cables to the correct position. My point is trouble shooting can be fun and why wouldn't we want to do it instead of sitting having a cold one. Glad you made out ok congrats on fixing it. bill
 
Back
Top