Led flashers too fast on Farmall when engine running

Radec Aksarben

Well-known member
Looking for help on this.

I installed led flashers on my 49 Farmall M. I used small led lights from a local supply store. The flasher came from Napa and the parts guy gave me one that he said would work with led lights.

After installation, they work perfectly..... unless the engine is running! With the engine running they flash rapidly and inconsistently. The power is drawn from the ampmeter in the dash box.


Anybody know how to fix this problem? Thanks
 
Based on the word "inconsistently", my guess is the flasher is some sort of high-tech solid state controller. Noise from the ignition system is probably messing it up. Try sticking the flasher inside a small metal box.
 
It's strange that it would change depending on whether or not it is running. If it clicks, it's probably the relay style for which the cycle speed is dependent on the current load. With LED lights, the current will be so low that it will click on and off too fast. I'd recommend trying a solid-state flasher which is not dependent on the load.
 
You need to remove the feed wire from the amp gauge and hook it into something that is not directly inline with the charging circuit
 
If your headlights are working properly and if you want the flashing lights to be independent, hook to hot side of light switch. If you need them to work with light switch, hook wire to output side of switch.
I have heard this but have not tested it to be certain, that if you leave at least one incandescent bulb in the circuit along with LED bulbs, the old relay style flasher will work normally. Makes sense but don't know for sure.
 
The power for the incandescent headlight switch is also off the ampmeter. I used that post to power the flashers. Wouldn't tapping power from the got side of the headlight switch be the same thing? As far as I know everything on the dash that is powered will get more voltage when the alternator is spinning.
 
Does the tractor have generator OR has it been converted to alternator? ---- something could be overcharging, or not be regulating properly. led stuff is super picky on the amps. Ignition shouldn't cause a problem.---don't take much to throw it off. That's why I never use led stuff on anything. --- I would try the transistor type relay first and see if it might regulate better. It was my understanding that led requires a steady regulated flow of current to work right. Older equipment may need extra filters/regulators/relays/etc.
 
Do you have any more guidance on what you mean by filters/regulators...etc? You are most likely correct by the way, judging what I observed today.

The tractor has been converted to an alternator.
Today I went out there with a volt meter. It charges around 15 amps when running at every powered post or wire I checked. Seems pretty high but have never had trouble with it other than these darn LED lights!

I observed some strange things messing with it for a little while:

As before, with the engine running, power coming from the amp meter, and flasher circuit switch on, the flashers stay mostly on and flicker off sometimes. If I hold my ear near the flasher it clicks at regular intervals but the intervals seem longer than they should be.
https://www.youtube.com/watch?v=63ljUBxw1us

I noticed this time when the engine is running and the flasher switch is off both the reds and ambers flutter!
https://www.youtube.com/watch?v=tLJJ2hefxl8

I disconnected the reds completely from power at one point and they still fluttered when the engine ran!

I moved the power wire from the amp meter to the hot side of the ignition switch. No difference.

Tried an identical flasher from the same store. Actually made it worse. The flashes didn't happen at all when running. Worked fine when engine off.

Put the old flasher back in. Moved the reds to turn on the headlights so different switch powers them. Noticed when the engine is off and the flashers run, when the ambers flash off, the reds will flutter.
https://www.youtube.com/watch?v=9hnhefdbZd4

I don't understand!!!!
 
Radec Aksarben":3mn2umiy said:
. . . I disconnected the reds completely from power at one point and they still fluttered when the engine ran! . . .
Do they still do that if disconnected from the flasher?
 
Not sure how helpful these pictures are.
The amp meter and headlight switch is in the normal box.

The switch (no relay) and flasher are in the top rusty box.

The flasher has a ground wire that is grounded and threaded to the top box. There are 2 prongs on it. One marked L for the output and the other is X for fused power. There is a 20 amp spade fuse on the hot side of the in/out light switch that powers the flasher. There is also a glass 20 amp fuse on the switch. The L wire off the flasher splits to each of the 2 amber flashers.

The second picture was actually taken before the 1st when the reds were also powered off the IN/OUT switch. They were removed for the 1st picture below.

20190427_175251.jpg20190427_171915.jpg20190427_171900.jpg20190427_171852.jpg20190427_171841.jpg20190427_171835.jpg
 
Then I'm back to my original comment, except the RF is acting directly on the LEDs rather than (or as well as) the flasher. Take one of your lights and hold it close to the distributor while it is running. It will probably really go nuts. You can use one of the lights to find where the interference is worst and thus identify the source. Then you can attempt to remedy it. You might be able to fix it by changing to the dreaded resistance spark plug wires.

You might try putting a light inside a metal box to test whether that would reduce or eliminate the problem.
 
These lights are grounded through the mount screw. Maybe I could ground them with a wire and hold them by the alternator just for fun as you suggest.

They are sitting within a 5 sided 1/4" steel box now in my fender extensions

20190427_172503.jpg

Might come down to trying to find an incandescent light that small too.

What do you mean by "dreaded resistance plug wires" wiring is not my thing. I'm embarrassed to not know what you are talking about. I just go to stores and ask for plug wires for the application when I replace them.
 
Back
Top