I hope this makes since, I’m doing two things at one time, watching the World Series and doing this. That makes me on overload!!! :roll:
If your test lamp is illuminated and you have followed the example in the prior post, you have to find were the parasitic draw is coming from. To do this you should remove a circuit protector (fuse) or relay from each circuit one at a time until the test lamp goes off. After you remove the fuse or the relay put it back in place so you don’t get them mixed up. Than repair the circuit that’s at fault. Remember remove the dome light if you have to leave the door open to get access to the fuse box. Also trip the door latch, just in case the security system is activated through it. If I knew the vehicle’s operation I could tell you where each component was, sorry to say I don’t. See
Figure 1.
Note: If you have a digital multimeter you can use it in the place of the test lamp.
Next to test parasitic draw with “on board†electric control units…
I will use the term “flow of electrons†for the movement of electricity which is amperes. Electronic control units (ECU) most of the time use less voltage and amperes than the primary voltage/amperes than the vehicle is using. ECU’s, most of the time operate at 5-8 volts (V) and milliamps. (mA)
Believe it or not 750 mA (3/4 amp.)will discharge a battery in one day. It’s very important to check for negligible flow of electrons which will in time discharge a battery. In the vehicles of today the on-board modules will discharge a battery in 30 days if not charged.
First you need a tool that looks like this.
Fig.2 (Tool manufacture -Kent Moore #J 38758) It’s a tool that is used to disconnect the negative side of the battery from the vehicle and route electrons through a digital multimeter(DVM).I think you can make one from a knife switch as long as you can protect it from shorting out. Remove the negative battery cable and attach the tool between the negative battery cable and negative battery post.
Fig.3 The tool has a on and off switch via a knob. Do not turn the parasitic draw test switch to the OFF position with the engine running. Damage will occur to the vehicle's electrical system.
Next step: you have to drive the car through what is called a drive cycle to wake up all on board modules. This is normally 15 miles at normal driving habits. After the drive let the vehicle set for 20 minutes key off, out of ignition switch, doors closed ect. Note: Before you get out of the car release the hood and open it and remove the underhood light. The reason you need the vehicle to set for 20 minutes is to let the ECU's (modules) to go back to sleep.
Next comes the confusing part. The reason for the DVM is to check for the flow of electrons in milliamps. You have to be very careful not to put more than 10 amps through the DVM or you will damage the multimeter or open its fuse, which is expensive. To see if there is more than 10 amps you need to attach 10 amp fuse in series like shown in
Fig. 4 and turn the parasitic draw test switch to the on position. If the fuse does not open you can safely install the DVM for the parasitic draw test as you see in
Fig.3.(Red and Black leads of the DVM) Set the DVM to mA
Fig. 5 and notice the reading on the meter. I would say a vehicle of that type any reading over 25 mA is out of specifications. If you are over 25 mA you need to find what electric control unit is not going to sleep.
I hope this helps somewhat… :?
Jack Fowler
Note: The red trace shows flow of electrons.
Fig.1
http://img.photobucket.com/albums/v688/Jackf/MVC-007F.jpg
Fig.2
http://img.photobucket.com/albums/v688/Jackf/MVC-009F.jpg
Fig.3
http://img.photobucket.com/albums/v688/Jackf/MVC-004F.jpg
Fig.4
http://img.photobucket.com/albums/v688/Jackf/MVC-008F3.jpg
Fig.5
http://img.photobucket.com/albums/v688/Jackf/MVC-005F.jpg
Other views of the parasitic draw tool:
http://img.photobucket.com/albums/v688/Jackf/MVC-010F.jpg
Notice the hook up points on the parasitic draw tool:
http://img.photobucket.com/albums/v688/Jackf/4.jpg