Inherited car

jakeesspoo

Well-known member
I recently inherited a 1976 mercedes 280s from a great uncle. Its a very clean car for its age and it started up after I charged the battery. Well, a few days after I got it I went to start it again and it was dead. I put a new battery in it and it ran fine...till I let it sit a couple of days and dead again...You get the point. If I start it every day or drive it its fine but let it sit for a day or two and the battery is dead. Alternator is charging when running. I was told he just had the alternator replaced not too long ago, could there be a blocking diode like in a cub that wasnt put in the system or just a short in the wiring maybe? This is the exact thing my cub was doing until I put that diode in thats a "check valve for electrons". Im just wondering I imagine if I take it to a import mechanic they'll tell me it need rewired :? :?
 
The alternator has built in diodes. A diode will usually open rather than short out. Notice I said usually. If you think the alternator is the problem - disconnect it from the electrical system. Then immediately check the voltage across the battery terminals. Check the battery voltage again is several hours. If the voltage drops significantly - the alternator is not the problem.

I wish I had a good suggestion.

Eugene
 
Sounds like something is discharging the battery when the car is sitting, like a light or accessory that stays on when the ignition is off.
 
Is there an alarm system on the car?
sometimes they crap out and always stay in an alarm mode and quickly wear down the battery.
This happens with my wifes truck unless I put it in valet mode than it stops (but no active alarm anymore).
Short somewhere in alarm wires I guess but haven't had the time to find it.
I also have one of those solar powered trickle chargers that suction cups to the window and keeps battery charged on sunny days.
Works good so far plugs in through the cigarette lighter plug outlet.
Toolman
 
A multimeter with continuity test is a handy gadget for finding phantom shorts as well.......

Some never can be found.....I've scrapped cars because neither I, nor the mechanic could ever find the source of the persistent discharge......
 
Don't forget the Mercedes is a very different animal. :( :( :(

I've owned 8 of them (mostly diesels) and still have the one I always thought was the ultimate... a 450 SLC (NOT A DIESEL). It had issues when I got it but a 14 coat paint job and a lot of elbow grease brought it back to its' original glory. I last drove it in about 1988 and have had it carefully stored under multiple layers of dust ever since. It will no longer run due to an electrical problem with the fuel pump system. No doubt a set of oxidized contacts somewhere.

I have all the wiring diagrams but they don't help with color codes or finding components. Repairing it will be like re-inventing the wheel. :(

See... all the wires disappear into an elaborate wiring harness to possibly emerge somewhere else. Nothing is identified. :( :( :( Unidentified relays and black boxes are EVERYWHERE!

Cubs are a lot more fun.

Good luck, Jake.
 
Jake,

I’m no Mercedes Technician, but I will give it a shot to tell you how to diagnose your battery problem.

First, Check all connections; battery cable ends, grounds, alternator connections and ECT.

Second, check the charging system and see if the alternator is charging to specifications. General specifications would be 13.9- 14.5 volts 10-20 amperes at idle with no accessories on. Turn all the accessories on and check the voltage/amperes output of the alternator at the battery. Generally the voltage/amperes should be more than 12.0 volts and 5 amperes at idle.

If that test passes you need to test the battery. There are all few ways to check a battery, but one quick check would be; remove the battery cables and see if the battery discharges as it did before. If so the battery has an internal short and should be replaced. If it stays charged the next test would be on a fully charge battery. Attach a voltmeter to the battery, disable the engine so it will not start and crank the engine for 15 seconds and check the voltmeter reading. If the voltage output is less than 9.5 volts after 15 seconds of engine cranking and engine is cranking freely the battery may be an issue. If you have a doubt, remove the battery and take it to a professional and have it tested.

Next, if all those test pass, you need to do a parasitic draw test. There are two different parasitic draw tests that could be done depending if you have any “on board electronic modules”. I don’t know that particular car so I’ll tell/show you how to do both. First is the 12-volt test light method. Remove the negative battery cable from the battery terminal and attach one end of a 12-volt test light to the battery cable terminal end and the other end of the test light to the negative side of the battery. Make sure everything is off in the car. All doors are shut, hood lamp is disconnected, key is off etc. If the test light is off, you don’t have a 12-volt parasitic draw.

Next step would be a parasitic draw test for “on board electronic modules”. This one is a little more confusing. I’ll have to take some picture of the tool you’ll need and show you how to attach it to a digital voltmeter. I’ll try to make some illustrations tomorrow and post it tomorrow night.

Jack Fowler
 
thanks for all the replies. I will go get a test light soon to check out the parasitic test...I went to start the car today and it was dead. Only sat for two days since I ran it last. What a pain in the A** :!: Want another mercedes George????
 
I hope this makes since, I’m doing two things at one time, watching the World Series and doing this. That makes me on overload!!! :roll:

If your test lamp is illuminated and you have followed the example in the prior post, you have to find were the parasitic draw is coming from. To do this you should remove a circuit protector (fuse) or relay from each circuit one at a time until the test lamp goes off. After you remove the fuse or the relay put it back in place so you don’t get them mixed up. Than repair the circuit that’s at fault. Remember remove the dome light if you have to leave the door open to get access to the fuse box. Also trip the door latch, just in case the security system is activated through it. If I knew the vehicle’s operation I could tell you where each component was, sorry to say I don’t. See Figure 1.

Note: If you have a digital multimeter you can use it in the place of the test lamp.

Next to test parasitic draw with “on board” electric control units…

I will use the term “flow of electrons” for the movement of electricity which is amperes. Electronic control units (ECU) most of the time use less voltage and amperes than the primary voltage/amperes than the vehicle is using. ECU’s, most of the time operate at 5-8 volts (V) and milliamps. (mA)

Believe it or not 750 mA (3/4 amp.)will discharge a battery in one day. It’s very important to check for negligible flow of electrons which will in time discharge a battery. In the vehicles of today the on-board modules will discharge a battery in 30 days if not charged.

First you need a tool that looks like this. Fig.2 (Tool manufacture -Kent Moore #J 38758) It’s a tool that is used to disconnect the negative side of the battery from the vehicle and route electrons through a digital multimeter(DVM).I think you can make one from a knife switch as long as you can protect it from shorting out. Remove the negative battery cable and attach the tool between the negative battery cable and negative battery post.Fig.3 The tool has a on and off switch via a knob. Do not turn the parasitic draw test switch to the OFF position with the engine running. Damage will occur to the vehicle's electrical system.

Next step: you have to drive the car through what is called a drive cycle to wake up all on board modules. This is normally 15 miles at normal driving habits. After the drive let the vehicle set for 20 minutes key off, out of ignition switch, doors closed ect. Note: Before you get out of the car release the hood and open it and remove the underhood light. The reason you need the vehicle to set for 20 minutes is to let the ECU's (modules) to go back to sleep.

Next comes the confusing part. The reason for the DVM is to check for the flow of electrons in milliamps. You have to be very careful not to put more than 10 amps through the DVM or you will damage the multimeter or open its fuse, which is expensive. To see if there is more than 10 amps you need to attach 10 amp fuse in series like shown in Fig. 4 and turn the parasitic draw test switch to the on position. If the fuse does not open you can safely install the DVM for the parasitic draw test as you see in Fig.3.(Red and Black leads of the DVM) Set the DVM to mA Fig. 5 and notice the reading on the meter. I would say a vehicle of that type any reading over 25 mA is out of specifications. If you are over 25 mA you need to find what electric control unit is not going to sleep.

I hope this helps somewhat… :?

Jack Fowler

Note: The red trace shows flow of electrons.

Fig.1 http://img.photobucket.com/albums/v688/Jackf/MVC-007F.jpg

Fig.2 http://img.photobucket.com/albums/v688/Jackf/MVC-009F.jpg

Fig.3 http://img.photobucket.com/albums/v688/Jackf/MVC-004F.jpg

Fig.4 http://img.photobucket.com/albums/v688/Jackf/MVC-008F3.jpg

Fig.5 http://img.photobucket.com/albums/v688/Jackf/MVC-005F.jpg

Other views of the parasitic draw tool: http://img.photobucket.com/albums/v688/Jackf/MVC-010F.jpg

Notice the hook up points on the parasitic draw tool:
http://img.photobucket.com/albums/v688/Jackf/4.jpg
 
Back
Top