Hey Rudi I have a question????

Mag Man

501 Club
I have about 1000 or more small ash trees in a swamp on my property and was thinking of cutting about 20 to 25 of them down the ones I am looking at are about 6" through or so and pretty tall and straight. So here is the deal Harbor freight sells a 2x4 maker that clamps on to your chain saw and when you cut a tree with it you can cut a perfect 2x4 if you do it right of course. Can I use fresh wood like ash to build things like partitions and work benches and such or will they need to dry or will they warp on me . I figured you may know about this kind of stuff.
JON
 
Jon:

Sounds like a good plan to use some ash or any other wood that you have sufficient quantities of. Ash is kind of useful -- I think so anyways. We like ash up here..

Rule of thumb: Never use Green Wood to build anything if you can help it, unless it is caned/sapling type furniture.

As with any green wood, if it is stored incorrectly it will warp and twist and become a real neat pair of skis if you aren't carefull. There are a number of schools of thought on this..

Some say, put the tree back together (works real well on big trees- in otherwords you sticker each layer as you cut, and esentially let the tree dry in a close to original form - this is how it is done in some small European sawmills - primarily for furniture woods)

Some say, just sticker and keep it even.

Stickers should ALL be the same size. And ideally they should be 3/8" x 1" or 1-1'2 wide. This allows for pretty good airflow as you air dry it. Would suggest that if you do not keep it inside, that you at least cover the top of the stack from getting too rained on. DO NOT TARP IT CLOSED... :!: :!: :!:
 
Over the past yrs I have harvested and had sawed several thousand board feet of lumber. Plan on losing at least 20% of the stack. Not all boards will behave. Weight on top will help. I have stacked many concrete blocks on to help hold them down. Stacks of 500BF or more is best. Still your best wood will be towards the bottom. Air dry stickered outside for the first 3-6mos. I have tried it inside and even with 1" thick stickeres it still molded. Just not enough air flow in a building during the initial dry down. If possible then move the stack inside where it will further dry till it reaches equalibrium, should get down to about 8-10% after a yr or 2. Some will tell you thats still too wet. Sure kiln drying will come out at 4% but after a while it will rebound back to 8%. Just test the woodwork in your house or any furniture and you'll see. Also allow for some shrinkage. Cut boards at least 1' to 1 1/8" thick if you want 3/4" finish plane. Ash is pretty good but a little fisty. The easiest is walnut and cherry. Oak is terrible as is mable and elm. Good Luck!!
 
My own opinion, when dealing with ash or oak, is not to mill it too green...

I don't have an opinion about "stickering"........ however, it is always better to make a narrow, high stack, with spacer boards placed at intervals, to allow better air circulation. The weight of a high stack helps quite a bit.

Letting lumber dry outdoors, under tarp sometimes minimizes warpage as well, since it doesn't dry out too quickly....

Ash might not be best for use as a framing 2X4, however.....It can be wicked hard to get a nail into, and it splits at the ends something fierce.....

Those 2X4 makers can also be used, I believe, to make 4X4's, which also don't warp as easily, and make good lathe stock, or, can later be milled (on your table saw) to 1X4's for other uses............like shelving, molding, etc....

Just my generally worthless opinion....
 
6" dia. tree may make 2 ea 2x4s. Maybe. Most likely one. It would be better to cut into one 4x4 (3 1/2 x 3 1/2 actual). My other thought is to mill the trunk on two opposite sides, leaving the other sides uncut.

My thought. If you are going to lumber and mill out your own trees. Wait a year or two.

Eugene
 
IMHO those little logs would best be used for firewood or pulp. Decent lumber comes from larger logs and is cut farther from the center of the tree. That's the problem with currently available framing lumber today. It's nearly impossible to buy a stable stud, for example, because they are cut from tiny little logs (fence posts) and are very unstable. If their moisture content changes in either direction from what it was when they were milled they warp.

The last few years I was building houses I bought 2x4's only in 16 or 20 foot lengths. They had to come from larger logs and were therefore higher quality and more stable.
 
Thanks guys,
I can cut larger ones, I also can cut them and say saw them into 12.6 foot lengths and let them sit that way till spring.Or longer I just figured that there are alot of the darn things and I could use the studs?
What would happen if you cut and used them right away? Not for a house or anything just for like work bench and a wall to put plastic on in the garage. They will warp and bellow? I can also cut 4x4 that sound like a plan.
Just one of those things you think of while sitting in a tree waiting for a deer.
JON
 
George Willer":cowh5yiz said:
The last few years I was building houses I bought 2x4's only in 16 or 20 foot lengths. They had to come from larger logs and were therefore higher quality and more stable.

Thanks George for the tip.

Thanks guys for the othr tips.

Richard
 
Back
Top