Help with my 98 chevy truck

TractorChick

Well-known member
hey guys
I talked to some of you about my truck on the flashchat but I was wondering if anymore of you guys would be able to help.

I have a 98 chevy Z71 truck and it's shaking really bad from mainly 60+ mph. It's drinking antifreeze into the motor (haven't seen anything leaking onto the ground), it's puffing white smoke out the pipes (we're guessing it's burning the antifreeze). And it's not idleing worth crap and it's revving really bad. All sound funky but that's what it's doing. We're thinking it's either the head gasket or a cracked head or the cylinder walls are being eaten because of the antifreeze.

Any info on your opinion or advice would be greatly appreciated. We're getting so baffled about this thing.

Thanks guys!!
Amanda
 
I would pull the plugs and look that them. you can tell which ones are burning antifreeze. Then I would do a compression test and that should tell you if it is a head gasket. Also check the oil and see if it his antifreeze in it.

Has it overheated?
Kyle
 
Probably headgasket or a crack - head or block. The antifreeze normally does not eat through the cylinder walls on a gas engine, only on diesels as far as I know, and it's called cativation (sp). A diesel is suppose to have a special antifreeze or an additive to prevent that.

Does the shake appear to be coming from a rough running engine (caused by the antifreeze most likely), or from the chassis?
 
get a ford push to the local scrap yard and watch it get chewed up, then you will have done something good for the enviroment. Recycling scrap and junk is great. Check your compression and pull the head, or just geat a short block for about $3000
 
Chevy Z71 V8 I assume? There was a problem with the small block V8 in the 90s with heads cracking. You have classic symtoms of water into the combustion chamber. That spells one of 3 things 1, head gasket. 2 head gasket with warped head(s). or 3, cracked head(s) by all means when you tear it down have the heads magna-fluxed, and checked for flat. BTW- Recent overheating of the motor is a sure trigger for this problem. Frank
 
Sounds like the others have you on the engine part so....

It shakes around 60 and over.#1 you could so down :lol:
#2 Have you been playing in the mud or snow ? Check the inside of your wheels if you have mud built up in there it will throw the tires out of balance. I found this out the hard way $$$$ after a night of mudding in rice fields.
 
well Cubguy, it started to overheat a while back, about 2 monthes ago now but hadn't done anything like that since.

Paul, I'm not exactly sure. Shakes like the wheels are out of balance, but extremely bad. I'm not sure. Seems like to me it's from the rough running engine, but don't quote me on that.

wow junkman, wish you lived closer... sounds like to me you could fix it quite easily. My dad had a guy at work tell him the same thing about these being know for the heads and gasket going funky. Maybe there is some truth in it. :)

TJ I have been in the mud and snow but the highways and speeds that i drive, it doesn't stay in my wheels long at all

And to you ole ford people..... all i can say is Found On Road Dead.... at least mine isn't completely dead and it's sittin' in my driveway not the side of a highway like a ford would be. :)

Thanks guys!!!
 
Amanda, Paul has you covered on the problem. A mechanic should be able to isolate which side the problem is on and possibly pull only one head. It might be wiser, however to pull both sides to prevent more problems later on. You need to get this resolved ASAP! If you're getting that much coolant through the cylinders, you're also getting coolant in the crankcase, which will eventually damage rod & main bearings. Be sure, at the time of the repair, that the crankcase is flushed. Changing the oil & filter twice will do the job.
 
Aint no vehicle that can't be broken. If ya don't believe that , all ya gotta do is let my son have it for a few days :roll: :roll: Grump
 
Amanda,

Junkman is correct. You have either a cracked, warped head, or blown head gasket. One way to confirm is a compression test, just as cubguy mentioned. If the two adjacent (sp?) cylinders have the same low numbers it is a head gasket. If just one cylinder has a low number, and that spark plug shows evidence of steam cleaning, but no others do. Then it is a cracked or warped head.

Aluminum heads are unforgiving when it comes to overheating. They get hot one time and they are done. Do you have dual exhaust, can you tell what side of the motor the tailpipe steam is coming from? Only reason I ask, is, I assume, you either have a 5.7l or a 4.3l. Both are v-style blocks and have two cylinder heads. You may only have a problem with one side. May be some worth some money savings for you.


I'd check your oil too. Since your burning the antifreeze it's most likely not getting into the crankcase, but check it just to be sure.

The vibration is caused by the mis-firing cylinder (one burning the antifreeze) and lower cylinder compression. Mis-fires are noticable part throttle cruising with a load on the engine. For example, Say you have a stick shift transmission, your driving 35 mph in high gear. That's a huge load on the engine, if you had a miss, it would show up then. The same could be said for an automatic trans with overdrive. When the overdrive kicks in, the engine rpms drop and the load on the engine is increased.

Let us know what you find.
 
well dad and i worked on it over the weekend. We found that the intake gaskets were pumped up and split and that was allowing the antifreeze to get in that way. We replaced the spark plugs, fan belt, intake gaskets, valve cover gaskets, changed oil..... yeah i think that's all..... yep....... it was amazing how much junk was in it. Truely amazing.

Thanks guys for all of your inputs
 
Back
Top