Grosshart Post Hole Digger Drawbar Dimensions

Stanton

501 Club
Here are the dimensions of my Grosshart (Prewitt) Post Hole Digger drawbar. This drawbar came to me already built and it works, but the PHD hangs off the top plate by 2"+\- as seen here:
079 smaller.jpg
Let me suggest that the arms be cut approximately 4"-6" longer than listed below. Then prior to attaching the top plate to the arms, attach the arms to the finals, loosely mount your top plate, get your PHD set upon the plate, and connect the PHD to your particular drive setup from the PTO (because that distance may vary). Once all that is set, then you can accurately mark the mounting hole locations into the top plate and cut off the arms to be flush with it.

All connecting hardware is 1/2" (top plate to arms), while all implement mounting holes are 3/4" (final drives and top plate).

Drawbar consists of (3) items:
  • Left arm: 3"x2"x1/4" thick angle iron, 20" long (suggest 24" or 26")
  • Right arm: 3"x2"x1/4" thick angle iron, 20" long (suggest 24" or 26")
  • Top plate: 29-1/4"x4"x1/2" thick top plate

IMG_4542.JPG

Each arm lines up with and connects to (3) bolt holes in each final drive, starting from the second hole from the front (as seen below, from left to right):
IMG_4553.JPG
The hole measurements should be taken from your own final drive to ensure alignment, but all Cubs are standard. Starting from the end opposite the top plate, the first hole is 1-1/4" to centerline, then 6-5/8" and 9-5/8". The cutout open space for the final drive hub is 2-3/16" from the end and about 3-1/2" long. The cutout is about 1-1/2" deep at its elliptical center.
IMG_4549.JPG
IMG_4551.JPG
IMG_4552.JPG

The top plate has (2) holes that line up with your PHD's base. Use that to align and measure the holes once your PHD is temporarily in place and connected to the PTO.

The other holes are just arbitrary connecting bolts/holes that hold the top plate onto the arms. They are set back from each edge about 1".
 
Thank you for posting this. A PTO powered post hole digger has been on my radar for awhile now.
I rented a one person post hole digger once and every time it’d catch a root the handles would spin out of my grip and whip around hitting me like two Billy clubs. In all my years working for the Sheriffs Office and in a jail I never got so beat up or felt like I was in a fight for my life as I did working with that thing !
Never again. If I dig again it’ll be with one of these. ;)
 
My paperwork says auger specifications 6,9,10 or 12-in diameter. There is a extra length feed screw available for5-foot drilling depths and a post puller attachment for pulling posts straight out of the ground. Does anyone know what the post puller looks like I don’t have a pic of it. What size augers do you guys have
 
Does that thing swivel side to side or angle front to back?

How do you make a hole that is plumb on a 20% grade?

Looks like it is mounted pretty firmly!

Stanton, it looks like you need to get that auger dirty! :)
 
I've got the 9" and 12" augers. Here's a brochure of its capabilities:
Grosshart Post-Hole Digger1.JPG
Grosshart Post-Hole Digger2.JPG

And another showing the puller on page 2:
Grosshart Post-Hole Digger Brochure001.jpg
Grosshart Post-Hole Digger Brochure002.jpg
 
One nice thing is that it goes straight up and down!

You dont have to move the tractor to compensate for the arc of the three point augers or the loader mounted ones.
 
Interesting unit for sure! ---- as for the auger size, ---- 12" max is as far as you could push that unit. a 24" would be in a whole different class of diggers like the hydraulic drive units for skidloaders.
I used to dig a LOT of holes with the 1-man digger and was satisfied with them. The last 6 holes I dug were here for the gate posts around the garden and I dug them by hand with the 10' long handle linemans shovels that they used in the 30's to dig power poles in with! lol!
 
Back
Top