glue job

brichter

501 Club
Okay, so Seth and I started to redo the 63 Econoline pickup. He wants a different kind of ride when he starts driving in high school. one of the PO's (may he rot in hades) thought it would be cute to carpet the cab. He glued this atrocious red carpet throughout the entire cab. After pulling the carpet off, we discovered he had a good supply of glue because it is piled up everywhere. Now my question is, after scraping off the major portions of the glue globs, what can we use to dissolve and wash off the remaining glue. I'm sure some of you have had to remove glue at some time or other in your restorations. We would really appreciate all input on this because it has turned into a real job. Thanks,

Billy Ray
 
Try some xylene but make sure you use a respirator and have a lot of ventilation.

I would use a variation of the paint stripper trick of covering it with wax paper or plastic. soak a rag or paper towel with the stuff and lay it on the glue. Then cover it with some plastic and maybe duct tape the edges so the xylene does not evaporate and has a chance to soften the glue. Use nitrile gloves.

Also, a heat gun may help soften it up so you can use a scraper. This works for contact cement and that is what I suspect they may have used?
 
Billy Ray,

I have had a lot of luck using the tech solvent from NAPA. My auto body buddies use it for eveything. Seems to clean and remove all kinds of goop as well as reducing their enamel.

Rondell
 
We used the heat gun and scraper but this only gets the large globs and what we want is to wash the rest off with some good solvent. There are lots of little nooks and crannies you can't get with a scraper. the xylene sound good and we will hook up a ventilator system so we won't be at risk. Thanks for the input and hope we hear more.

Billy Ray
 
I friend of mine swore by liquid nitrogen. Apparently, you pour it over the glue and it freezes go hard it will fracture when scraped with a putty knife. Even the thin stuff. But there are other problems associated with liquid nitrogen like freezing the underlying metal so it fractures as well. But continuing the idea of cold, what about using a chunk of dry ice? The stuff I've seen is usually flat, and while it is cold, it is not as cold as liquid nitrogen.

Place a chunk of dry ice on a patch. Let the glue get real cold and chip it away. No residue from the dry ice and you can do a little at a time if you are so inclined. But do wear gloves!

Rick (has solution looking for a problem) Dulas
 
PLEASE take the battery out of that vehicle before using some of these chemicals - could be an early 4th of July !! Happy New Year everyone. Craig
 
Rick, we live in the backwoods of Northwest Florida. We don't even have wet ice much less the dry variety.

Craig, the battery is already out and the doors are off. plenty of ventilation with the big floor fan blowing through.

Thanks everybody,

Billy Ray
 
Use a slow solvent like Naptha, Xylene, etc. soak it good and before long you can scrape and scrub it off. Lacquer thinner or MEK will work but they flash pretty fast. Ventilate well and protect yourself.
 
3M Adhesive Cleaner is pretty good stuff. Mixture of Xylene and several other solvents. Do wear gloves, very flamable and very strong fumes, but it works. When I was younger, I had used the stuff without gloves, turned some of my fingers very white.
 
I found acetone to work for most types of glue. If you want to try a small sample to see how effective it will work on the glue you have, snatch a bottle of your wifes finger nail polish remover and try it. If that does the job it can be picked up in quart or gallon sizes at hardware and automotive stores. observe same precautions as noted above chemical gloves, ventilation, and yes flammable.
 
BR,

I've used both acetone and the 3M adhesive remover on exterior wood-grain stickers with good results. I've also used an electric heat gun to soften and scrape old glue, but this is tough on the old fingers too.

I won't repeat the wise and experienced warnings already listed above, but I have resorted to using plastic scrapers to reduce sparks. (don't ask why! :shock: )

Your post brought back some fond memories. When I was in high school, my older brother helped me buy and rebuild a 1956 Chevy 2-door station wagon. While that project was in progress, he let me drive his '63 Econoline van out on several dates.

What had my brother installed on the floor and walls? RED Shag carpet! Must have been a feature "how-to" article in Hot Rod Magazine or something, and back in the old days, the girls thought it was pretty cool!

Good luck!

Corky
 
How about using an angle grinder with a 3 or 4" cup brush and just smooth it out or sand it then just prime and paint over it?

Harbor freight had these brushes on sale for a while they were under $2 more like $1.76 each. I grabbed 20+ of them for my restorations.
 
Back
Top