Function of Grindstone

Dan England

501 Club
For the past few years, I have had a grindstone lying in a back corner of my yard. It has a diameter of 17 inches, is 5 inches in width and the center hole, which is square, measures 4 1/2 inches. It weighs 90 pounds. What would the stone have been used for? While on my property, it seems to have been a haven for fire ants as several hundred came boiling out, ready bite anything which moved, when I flipped the stone over. Any use of the stones today, other than as a yard ornament or fire ant hotel? Dan
 
weve got one very similar in size that my uncle said the farm hands used to grind corn into grits with. our fire ants like ours too! :D
 
Don: I had thought that it might have been used in sharpening tools but the ones which I have seen for that purpose had a smaller and circular center hole. Dan
 
You'll get a good laugh from this, but while I've been recuperating, I've been loading up on Bonanza and Gunsmoke episodes. Seems one of them had a scene in a blacksmiths shop, where he got on a pedal device with a grindstone like you mention. Could it be from the old blacksmith's era??? 8)
 
Sharpen tools. Wheels that size were mounted in a stand with sometimes a seat. You pumped the foot peddles to get the stone turning - like the old sewing machines.

Do not try to mount the stone - turning the stone with an electric motor. They are frequently cracked and will break.

Eugene
 
I have one much like you describe, square hole and all that I found years ago while excavating. I use it as the base for a sundial.

We had one on the farm... it was the bicycle type and the only grinder Pop ever had. We had a tin can suspended over it with a small hole to drip water on the wheel. Until we learned to run it the other way it always resulted in a wet crotch. :(
 
Well, tool sharpening seems to be the winner. I got it at a yard sale several years ago. It was lying loose, not attached to anything at that time. Harold, glad to see that you are up and going now. We will be in Monroe over the weekend. We will be building a deck and handicap ramp for Karen. We had hoped to bring down a van, equipped with a lift for loading and unloading while in a wheel chair but it is not going to be ready until sometime next week. Dan
 
Dan England":17atbax8 said:
George: Was the water used to cool the metal which was being ground with the wheel? Dan

No. It couldn't get very hot. It was to keep the stone clean and sharp. Some of them used a trough underneath so the stone ran in water. If it wasn't emptied when finished the stone would soften and wear lop-sided.
 
OK, another question George. What materials needed to be cleaned from the wheel? Would it be grit which was dislodged from the wheel or microscopic bits of metal? Or maybe both. Dan
 
Dan England":hz2ai1t5 said:
OK, another question George. What materials needed to be cleaned from the wheel? Would it be grit which was dislodged from the wheel or microscopic bits of metal? Or maybe both. Dan

Probably both. :D
 
Dan,
It sounds like a mill stone and Spiveyman is correct it is used in a grist mill to grind grain, probably most often corn. I'm sure you have seen the old mills with the water wheel? That was used to turn the stones as they ground the corn or other grain.
 
If it was a millstone it would have grooves cut in the side or both sides or at least the sides would be wavy from worn out grooves. I have one approx. that size with the handle still on it and was used for sharpening. I'll try to get pics this weekend of both the sharpening and millstone. Also the millstone USUALLY has a courser grit than the sharpening stone. Grump
 
After reading the responses, I took another look at the stone this morning. The outer surface (where the tread is located on a tire) has a distinct and continuous groove. The groove is not centrally located as it is about 2 inches from the edge of the wheel. Going to the sides of the grindstone, one entire side is quite rough. The other side is much smoother, as though the bumps and indentations have been worn away. Is the stone large enough to have been part of a gristmill. In a gristmill, would the grinding be on the outer surface as defined above or would the grinding action be done on the side of the stone. I would think, if used to sharpen tools, the wear would be on the outer surface rather than on the side. Let me know what you think. Dan
 
Grumpy: There are no grooves on the sides and the sides aren't wavy. Both sides are straight, the only difference being rough vs smooth. Dan
 
Millstones are usually much larger than the 17 inch diameter that you described. The channels or grooves that Grump mentions caused the grain deposited in the center of the stone to move outward as the stone turned. Otherwise, the grain would stay under the millstone and be ground to a fine powder. The groove or wear on the circumference of your stone is from sharpening small tools, like dressing the point on a punch or chisel. Frequently, the sides of the stone were also used, accounting for the stone being smoother on one side. You'll see the same wear patterns on your smaller bench grinder wheels.

Here's a millstone.
http://en.wikipedia.org/wiki/Millstone
 
Millstones are normally cut from granite or other hard stone, and have grooves cut into the sides. They were used in pairs, one turning, one fixed, and the grain was fed thru the center of the fixed stone to the grooves in the stone where it was ground into meal as it made its way to the outside edge of the stones, where it was collected. You need hard stones to keep from getting stone dust/chips in the meal you are grinding.

Grindstones are normally sandstone or other soft gritty stone, and are smooth sided.
 
Paul: The stone is the soft and gritty kind. Each characteristic seems to confirm that it is a grindstone used for working metal. Dan
 
Back
Top