Ford ranger/mazda Rear Rust!!!!!!!!!!

BigBill

501 Club
My son purchased a 2000 ford ranger brand new. It now has 120k on it and its still like new mechanical and body. The problems started with a rear differential leak. He installed a new pinion seal and resealed the rear diff cover. But it had another leak thats hard to see. It had pin holes were it rusted thru. I welded a piece of sheetmetal over the rusted out area and its welded from the inside and the outside so its double sealed. Now another problem started with a clicking sound when he hit bumps. He inspected the rear springs and found the shackles rusted out and the frame brackets rusted out too. Everything is full of rust when we took off the bed. I found a bracket/shackle kit thats already available to solve this problem. I now need to double wall the frame in the rear section. The frame in this area is pretty thin even though it wasn't thick to begin with.

Dealing with rust can be pretty tough too. I have an idea that i use on stainless steel chimneys. I coat then with alumimum spray paint to seal the stainless from the outside elements like acid rain. My regular steel stove pipe single wall chimney in VT has lasted since '86 with it being painted only twice since then with alumimum spray paint. I'm thinking to wire brush the whole truck frame and prime it with the red rust primer and then coat it with the alumimum spray paint then paint it black and then tar the whole frame. This should stop the rust in its tracks and protect it so it will last for a few more years.

My point is if your getting or have a newer truck its a good idea to paint it underneath so all the bare steel is coated and then tar it so its protected for the future. In the past i did this on all my new trucks. I purchased a case of rustoleum black and painted the whole truck underneath it. Then i tar'd the fender wells, frame and spring brackets.

Another point is if you have a 10 year old truck you better checkout the rear spring setup.

I lost a truck back in 73 to rust and it rusted from the inside out were i couldn't seal it. I purchased another new truck in '88 with the new improved galvanized dipped body to stop the rust thru. Well I hate to tell the manufacturers it ain't working ! ! ! ! ! What you do with your truck is up to you but you need to protect your investment. I figure for what new trucks cost today they should last us a longtime after making payments for so many years. I like not having payments for many years after its paid off. Its a free ride after its paid off so we need to make it rust free too so it lasts.
BB
 
I have a 1994 Ford Ranger. Up to this point I have replaced both the front mounts and the rear shakles and mounts on the rear springs as well as the rear cab mounts. You may want to check those while you are working underneath it. My biggest problem now is the mounts on the rear axel for the shocks, and the rear gas tank strap (currently held up with a ratchet strap). I was told that the reason these parts are so bad is because they were dipped in plastic before they were installed, and when they got scratched they held water. Then they rusted from the inside out.
 
I too have a 200 ranger purchased new. had to replace rear springs and shocks at120,000 miles . Now at one 160k with replaced tranny, rear diff cover plate (rusted out). just found a great local shop. 500,000 miles here I come! North east winter salt sucks.
George
 
The car companies don't want you to keep a car/truck to long. They want you to buy new ones.
And the salt you use on the roads up north doesn't help either.
 
They had a bad problem with rust on them. I have done about 7 or 8 full sets of shackles. I have also replace a hand full of cab mounts.
Kyle
 
I have an 01 Ranger, and have not crawled under it for close inspection, but will do so. so far the only rust I have noticed is speckles on the rear bumper. One thing in our favor is we are not as far north, and probably do not get exposed to near as much salt as you do. I did notice when running brake and power wires to the rear of my 06 F-150 that the inside of the frame, as well as the outside was coated with some sort of real sticky substance, which I assumed is a rust proofing/delayer. Made fishing wires through the box frame a real pain.
 
Big Bill,
No undercoating up in the Northland?? I have had my last 2 Toyotas Ziebarted and had no problems and I drove them on the
beach and in salt water. Trouble is shops that do that are getting hard to find. 1993 Toyota 10 yrs. no rust. 2003 no rust
yet. At least use some spray on undercoating. Toyota sent me a notice that they are having problems with rust perforation
on some years frames now! I wondered why said my chassis looked so good and what I did when I took it to the dealer last
year for a ball joint recall. You got to cover that cheap metal on these expensive vehicles with something!!
 
I crawled under my 01 Ranger and looked over, only very minor surface rust on the frame, non at all on the spring brackets. I did find pretty bad rust on the differential cover though, guess I better wire brush and paint it as soon as the weather cools a little.
 
My 96 F-150 ,done the lines[brake,trans and p/s] and the mounts and shackles.IT WAS UNDERCOATED!!! They did not honor their deal either.I WILL NEVER UNDERCOAT a truck again.I still work a new car dealers and have told customers what they did to me.STILL NOT HAPPY!!! And they took my $$$$$ every year on those check ups. :evil: :evil: :evil: :evil: KETCHAM
 
The kid paid for the special undercoating but there's nothing on the frame, i guess they did inside the cab and fenders. I had to cut open the rear part of the frame and install two 18" long x 4" high and 1/4" thick metal plates so the small rust threw spots were covered. I put one plate on the inside the frame on both sides. If you take off the bumper only the end of the frame is accessable if you cut the gusset at the end rail just enough to slide in the plate. Then you can weld the end back up again so it still has the orginal structural integerity.I deceided to plate the inside of the frame only. I realized if i plated the outside of the frame down to the cab that puts a bending moment at the frame under the cab where its not sandwiched. That could cause a vertical crack where the bending moment would be sooner or later. The rest of the frame looks ok anyway and the kid only carries his dirtbikes(2) with the truck. On a really bad frame i'd have to either double wall it from the back to the front and box it in some spots so it would be safe and not have a bending moment or a weak spot. Once we start boxing a frame we actually chase the bending moment/weak spot down the frame rails so we have to do it right. My '55 jeep tractor is boxed with 3/8" plate from the front to the rear its a tank now with the added weight. Its a bear pushing snow with the lockers in the diff's. My point is if your going to build something do it right. I only do things once.

So much for zebarting......

My '79 C20 3/4 ton chevy is undercoated like 3/8"+ thick on the whole truck. Thats why i still own it. It was probably owned by a construction company or a local town because i never seen undercoating this good. But the gas tanks are rotted out and the body needs a little bondo now. For a $1,000 investment in parts i could have a perfect truck again. Since its an 8 lugger with 13" rear brakes its worth fixing because its probably a better truck than i could buy new right now. The new trucks are junk for work anyway until we spend at least 40k.

I owned and stripped 3 chevy 4x4's in the past because of rust. Two suburbans and one pickup a '73, a 76 and a 78. In '88 i purchased a new suburban for 27k and the trucks i stripped ran better than the new one. I actually junked better trucks than the one i paid 27k for. I haven't owned a new GM since and probably never will ever own a new american made car or truck ever in my lifetime again they can keep there crap let them drive it.

My new '97 subaru is at 200,500 miles now and it still runs like new. My new 2010 subaru legacy is made in the USA and runs awesome too. I wished subaru offered a little pickup with the boxer engine there awesome. The boxer engine is so much smoother even over my jeep 4.0 inline 6 cylinder.
 
cubguy":1ouge9hz said:
They had a bad problem with rust on them. I have done about 7 or 8 full sets of shackles. I have also replace a hand full of cab mounts.
Kyle

What would a job like i did with installing plates in the frame and a full shackle/bracket kit cost if someone done it??? My son was thinking with todays labor costs about $800 to $1,000 to repair the rear springs? I spent $125 for the kit and $80 on paint and undercoating if i added it all up. Wait two 6011 welding rods and a quart of gas in the gas engine welder too plus the oxy/acc torch to cut the rusted stuff off and cut the plates out of channel. So were looking at around $225+/- our cost.

BTW; My son did all of the work drilling out the rivets and wire brushing the frame inside and out. His labor and i just welded for two minutes and painted it while he was at work. This has been an awesome buy for the 2k Ford Ranger being a joint venture with mazda. It lacks a little in the rear leaf springs thats the only thing i can find wrong with the design it needs a 4 or 5 leaf rear spring from the factory.

My firewood truck ('76 C30) i made it into a 4x4 because in 77 they had the first 1 ton 4x4's. I had 72 leaf springs with 10 leafs in the fronts on both sides and 16 leafs in the rear main with 10 leafs in the helpers on each side. I stiffened it up as i went. I almost rolled it loaded with over 15k lbs of firewood so i stiffened the front up so it wouldn't tilt so easy on uneven ground. You can have it sag either when its loaded so the local LEO's don't pick it out its loaded so much. I went everywhere a slidder would go driving right up to the wood to load it. It road like an old truck when it was empty but it was like a BMW smooth when it was loaded. At homedepot we put a full bundle of 16' long 4"x6" PT timbers and i think it was 58 pcs total in it without a sag. It already had the 8" c60 frame in it with the 11,000lb rear dana 70. You can't buy trucks for this kind of work they need to be built.
 
Big Bill,
Did he pay the dealer for the undercoating or did he take to an independent shop :?: :?: Zeibart had an excellant warranty
but you had to bring it back each year for a checkup. I never did and got 10 yrs. no rust. Z. was only done by independent
shops :!:
 
I believe the dealer had a program setup with zebart i think for undercoating it. There was nothing under it when we took the bed off of it. The frame is bare so the kid got screwed along with most others i guess. The kid is looking for the paperwork now. I told the kid from now on when you purchase a new car or truck get yourself some rattle cans of rusty primer and high gloss black paint and paint everything underneath the vechicle. They buy the rattle cans of undercoating and soak them in hot water or leave them out in the hot sun to warm up the tar like substance and spray everything again with the coating. Then you know its done. On the factory boxed frames its good to drill holes in the bottom of the frames so they can drain when the water gets in them thru the side holes like on the jeep frames so they can't rot out from the inside. My point is we need to protect our investement so it will last for many years down the road so our investment pays off by not buying car/truck every 5 years or so when its just paid off.

This is why i purchased my '79 C20 3/4 ton truck its in decent shape yet repairable but i can work on it because it has no fancy electronics. I'm thinking of restoring my old jeep tractor too with 4 wheel disc brakes, a manual master corvette brake master cylinder along with a new complete body. I'll leave the boxed frame and plow snow with it. I have a retired '99 jeep wrangler thats sitting here for me to drive and i was thinking about plowing with that. But its not as much fun as the older jeeps were i really miss my '80 CJ7. My sons will help and we will have a like new jeep when its done. It only has ignition points to worry about, give me the old time simple repairs. I wish we had the 50's stuff back again.

When we go to Wells,Maine we go to the old car museum there and i see cars that i worked on as a kid in it. Boy i got old so fast the stuff i grew up with is in a museum now. It kind of makes me think how old are tractors are too. God life was simple once wasn't it? :D Time goes by so fast........ :?:
 
Back
Top