Fighting my John Deere's...

Ben B

Well-known member
Yesterday was a battle I didn't plan. I had a lot to do and the machinery was putting ME to the test, instead of the other way around. The 111 is a hand me down from Dad. It has a newer engine, but is a smaller machine with a 38" deck. I've got four acres of not-so-level land to mow, and it just wasn't getting it done. It gets hung up and stuck and just sets too close to the ground. It would be great for a lawn. But, what I have is not what I categorize as a "lawn".

Sooo, I go get the 112. It takes off like gang busters! Bulldozing through tall grass with its 46" deck. Then, it starts starving for fuel. I limped it up the hill to the garage and start trying to figure out why it isn't getting fuel. The fuel strainer was clean as a pin. So, I go back on the 111 until the 112 cools off enough for me to work on it.

I finally figured out that the 112 is vapor locking. The fuel line goes through the engine shroud. Once I rerouted it outside of it, it quit the vapor locking. So, I take off again and then the deck starts slipping. I go back and have to adjust the clutch on the PTO. Finally, the last 20 minutes or so I got to have smooth sailing on the 112. But, it needs some more work. I discovered the carburetor is cracked on the air intake side. :(

What's this got to do with a cub? The whole time I was fighting these cantankerous contraptions I was talking to myself saying "I'll be glad when I get enough money saved up to buy me a CUB!" This place was so much easier to take care of when Dad had is cub. I could mow it in an hour instead of four! :x

My current plan is, this coming winter will be spent working on a Cub and getting it ready for next year's mowing season. The 111 will remain for doing trim mowing around the house, and the 112's fate is undecided. I may tuck it away and restore it in a few years. When it runs, it runs good.

Ahhh, the joys of using old machinery! I know a cub will have its own faults to deal with as well. I do enjoy "Fighting" with my old machines. I guess I"m just nuts!
 
signalyard":1hi9011s said:
...Ahhh, the joys of using old machinery! I know a cub will have its own faults to deal with as well. I do enjoy "Fighting" with my old machines. I guess I"m just nuts!

Nothing nuts about enjoying the old stuff. Sounds normal to me.

Bill
 
Bill Hudson":379qgeg4 said:
signalyard":379qgeg4 said:
...Ahhh, the joys of using old machinery! I know a cub will have its own faults to deal with as well. I do enjoy "Fighting" with my old machines. I guess I"m just nuts!

Nothing nuts about enjoying the old stuff. Sounds normal to me.

Bill

Not to hijack this thread, but I got the new radiator on my mower cub yesterday. (Thanks, DirtyRed). Got it back together. Man, that thing ran like a champ. Cut about 2 acres. Can't believe how good a job it does with the belly mower. I MUST get myself a new seat tho, that plywood seat bottom has taken it's toll. :oops: :{_}: :{_}:
 
Don't fight the machinery, just go with the flow. Gas flow, oil flow, blood flow, sweat flow or whatever else happens to be flowing.
 
Mike in Louisiana":2ft4bvq8 said:
How about a little overtime at the job and get that cub now.

My kind of guy!

I work every minute of overtime that they will give me. That's what I'm saving up. By fall, I should have enough to get me a cub.

I had a little more excitement this morning. The 111 wouldn't crank over. Turned out to be corroded battery terminals. No big deal. But, I have to leave it on a trickle charger because it will not charge on its own. It hasn't ever since Dad replaced the engine.
 
Oh yhea! Dad's cub would do in an hour what my Deere's take at least four to do. My biggest problem is that I work out of town and my weekends have to be productive. Spending four hours on a machine to do four more hours work on the yard is kind of frustrating.
 
Well, the battle with the John Deere's continue... Saturday the 111 broke a connecting rod in the engine. Dunno why. It has plenty of oil in it and was purring along when all at once there was a "clunK" sound and that was all she wrote.
The 112 also has problems. It keeps starving for fuel, but its getting to the carburetor. I think the float must be sticking. I just took it apart the other day and cleaned it and it looked good... :(

All the more reasons for me to get a machine that can handle the job. I'm working lots of overtime to try to get one.
 
Hope you get all the overtime you can....

That is what happened to my Craftsman. Good mover/workhorse for me for almost 15 years.. engine was always strong and kept the oil changes regular. Never used any oil. Only major problems I had with it was the constant replacement of the spindles and I had to rebuild the rear end once. One morning, mowing the lawn, engine running really well. All of a sudden a bang.. and that was all she wrote. Took it apart and the bosses were busted and it threw the rod. Not even a parts engine now...

So my bride bought me a Deere :!: :wink: :D
 
signalyard":gddw01si said:
Well, the battle with the John Deere's continue... Saturday the 111 broke a connecting rod in the engine. Dunno why. It has plenty of oil in it and was purring along when all at once there was a "clunK" sound and that was all she wrote.
The 112 also has problems. It keeps starving for fuel, but its getting to the carburetor. I think the float must be sticking. I just took it apart the other day and cleaned it and it looked good... :(

I think your machines are trying to tell you something - get that Cub ASAP. :D :D
 
Back
Top