Electrical question - 220 to 110

paw's49

Well-known member
Fellas,

The dear wife wants to replace the current smoothtop electric cooktop with a gas cooktop. Claims it will be much faster in heating/boiling the water for canning. I agree, the electrical is sooooo slow, in fact, almost not worth the trouble of trying to can. I've never cooked with gas, but she has, and says it is much faster.

Anyway, the current cooktop is wired 220 of course. The gas cooktop has a 110v power cord for the electronic ignitor. I'd like to try to do the electrical myself, but sure don't want to get fried, or burn the house down, trying to figure out how to take that 220 line down to 110.

I've searched the internet, and from what I've read, I need to replace the 220 breaker with a 110. I've read that 220 has two hots, a neutral, and ground. I've read to replace the breaker, cap off one of the hots at the breaker, cap off the same hot at the receptacle, using just one hot, the neutral, and ground.

Is this something I could do, or best left to the pros?

Thanks!
 
Hi Paw's49 - You're right that's what you need to do. Honestly, it would be better to have a pro do it. The great thing about going this way (from 220 to 110) is that you will have everything you need except the new outlet and breaker. It is much safer to do this than only trying to tap into one of the legs of the 220.
 
You're right about the way 220 is set up, and in regards to the wiring of it, as well as changing it over to 110.

I'm not a licensed electrician, but I've been playing with AC/DC and electronics my whole life, and what you propose to do will accomplish what you are wanting to do.

My only question would be this: Can you simply "Cap" the unused wire and leave it there in the main supply circuit box? Like I said, I'm not a licensed electrician, so I don't know the proper codes for this in your state. My advice would be to contact someone who knows the Electrical Code Rules in you state/area, and ask them that question. You might even be able to find out the info on the internet? If it's "YES" and you feel comfortable doing it, go for it, but play it safe and have someone around when you are in the main ciruit panel box. I do my own electrical work inside the house, but when I'm out playing around in the circuit panel box, I like to try and have my wife around just in case something happens.
 
Paw's 49,
As an electrician myself, have it done, even if it's just for insurance co.
and get a receipt :lol: :lol: :lol:

Gilles :wink:
 
I have to agree with everyone else, get someone there that has experience. Preferably with license. I'm not an authorized electrician, but I have wired a few houses and barns. (some with mistakes that had to be fixed) But I don't do what is right all the time. If it were me, I would get a 30 amp, 110 breaker, remove the 2 wires from the 220 breaker, put the ground wire and the white wire to the ground bar, the black wire to the breaker, go to the other end and put in a standard female plug-in, hook the black wire to one side and the white wire to the other side, ground wire to ground, plug in the igniter, and turn it on. I've never capped a wire off, just put it on the ground bar. I hope you luck though.
 
Merlin,
your a dangerus man :lol: mecanical ground and neutral bar sould not get mix, you would feed return electrical feed to your ground system :roll:
thats a not to do thing :wink: ground wire to ground bar and white to neutral bar ok!!! belive me when i say insurances look for those mistaque not to pay excuses :evil:
but that's just me you can do what you want it' your house 8)
Gilles, :wink:
 
Craig:

1. I agree with your better half. Gas is much quicker and more economical as well as it does provide a better smoother heat to cook with and is infinitely adjustable almost. But it can be a pain if the pilot goes out.. at least on the old models. The new ones I think have auto spark and the gas shuts off when the contorl is turned off.

2. I agree most emphatically with the other opinions expressed about having a QUALIFIED and LICENSED Electrical Contractor do the conversion. If anything happens you will be well served by the receipt for the service. As a cabinetmaker and business owner, you have no idea how important it was for me to ensure that any electrical or gas work was done by a Provincial/State Licenced Contractor.

3. Don't skimp on the contractor ok.. use one :!:
 
GILLES":3q1vn6si said:
Merlin,
your a dangerus man :lol: mecanical ground and neutral bar sould not get mix, you would feed return electrical feed to your ground system :roll:
thats a not to do thing :wink: ground wire to ground bar and white to neutral bar ok!!! belive me when i say insurances look for those mistaque not to pay excuses :evil:
but that's just me you can do what you want it' your house 8)
Gilles, :wink:

You're probably 100% right GILLES. But that is the way I was taught about 60 years ago, so I just keep doing it. My breakers on my meter pole outside and my breaker pan in my house is wired like that. All the older houses/barns I know of is wired like that. I'm not sure how they do the new houses,barns these days. I know they started inspecting them now, but I have no idea what they are looking for as I just do my thing and ignore all the bureaucracy.
 
In this day and age, you hire a master electrician but he sends an apprentice to do the job. Never trust the student to do the work of a teacher. Make sure the work is inspected to meet local building code. You need to do your homework to make sure the work you contract is done correctly. Been there, done that - both in the urban jungle and rural countryside. Either energy source can convert your property to smoldering rubble or worse.
 
Schooled in the National Electric Code and done a bunch of commercial and residential wiring. Just my opinion.

There are a couple of options you need to discuss with the licensed electrician. One is to split the 220 volts in two seperate 110 volt, 20 amp, outlets (in the same receptacle/box) (meets a kitchen requirement for seperate 20 amp outlets). That way you do not have to remove the 220 volt wiring and replace with 110 V (yup thats a code requirement. You gotta pull unused electrical wiring).

Eugene
 
Eugene":1l5u531n said:
Schooled in the National Electric Code and done a bunch of commercial and residential wiring. Just my opinion.

There are a couple of options you need to discuss with the licensed electrician. One is to split the 220 volts in two seperate 110 volt, 20 amp, outlets (in the same receptacle/box) (meets a kitchen requirement for seperate 20 amp outlets). That way you do not have to remove the 220 volt wiring and replace with 110 V (yup thats a code requirement. You gotta pull unused electrical wiring).

Eugene

Eugene,

You're describing the system used in my entire shop. There's a double box every 4' which can have four 120 V outlets every four feet or can be converted to one 240 and two 120 volt outlets. Believe it or not there are places there are not enough outlets.
 
George Willer":37evjjn5 said:
You're describing the system used in my entire shop. There's a double box every 4' which can have four 120 V outlets every four feet or can be converted to one 240 and two 120 volt outlets. Believe it or not there are places there are not enough outlets.
What I was thinking was taking one duplex receptacle and turning it into two each single receptacles. If possible, this would be a very fast - cheap method of converting to 110V outlets. The cost for the receptacle end of the circuit would only be a new box cover plate and one 110 V receptacle. The electrical panel end would simply require removing the 220V breaker and installing 2 each 110 volt breakers in the same slot.

Again this is where an experienced (licensed) electrician would be able to look at the current set up and provide some alternatives.

The retail parts for the conversion method I discussed would be less than $50-. That's a wild guess. The receptacle and cover plate would cost $3 or $4. The cost of the breakers will depend on which electrical panel is in the house.

Eugene
 
Thanks all for your responses. Still haven't hooked up with an electrician yet, even tho I've called two. Both said it would be a couple weeks before they could get out.

In order to remove the electric cooktop, I turned off the breaker and removed the cover plate on the inside of the house. All that was in there were two blacks and a ground. So both blacks are hot?

I see there is quite a bit of electrical experience in this forum. Would ya'll be willing to answer my dumb questions if I tackle it myself? Would some pics help? And, if I throw the MAIN breaker, does that remove all power from those bus bars in the panel, and allow me to do about anything I'd need to do in that panel?

Thanks again.
Craig
 
Craig, both blacks are hot. Your wiring must be a little old? It was common practice years ago to run just the 2 hot wires and a ground, but pretty sure that today's standards normally require the 4th wire, which would be the neutral.

Personally, I'd be a little wary not having the neutral if you are planning on splitting that circuit into 2 110V circuits, and not having a dedicated neutral.

Hopefully someone like Gilles, or someone else who has worked as an electrician will chime in with some good advice.

Here's a couple of links that should help you out.

http://www.faqs.org/faqs/electrical-wir ... on-16.html

http://forum.doityourself.com/archive/i ... 56763.html
 
IT, yes, the house was built in 1971, and has never had a wiring upgrade. But I would think there would be plenty of voltage in that panel. This house was built back when electric baseboard heat was all the rage (at least in these parts - in fact, the local power company called them "total electric homes"). I went with a gas pack several years ago, and disconnected and removed all those baseboards -- one in each room.
I was looking for a neutral also, and was surprised not to see one. I tell ya, those are some big fat wires :D - I don't know if I could get one of them wrapped around those outlet screws or not!!
 
Lurker Carl":1rkr1rl4 said:
In this day and age, you hire a master electrician but he sends an apprentice to do the job. Never trust the student to do the work of a teacher. Make sure the work is inspected to meet local building code. You need to do your homework to make sure the work you contract is done correctly. Been there, done that - both in the urban jungle and rural countryside. Either energy source can convert your property to smoldering rubble or worse.

It can be a mistake to trust your fate to the skills of a licenced electrician and the diligence of an inspector.

Some years ago my son and I were called in to finish a job in a different county after the owner had a dispute with his general contractor. We were used to working with our own wiring but we never found the need to become licensed. (our work was always to code as we best understood it) In any event, we had just seen the local inspector complete his work and sign it off so we reasonably assumed the wiring was to code. WRONG! The outside receptacles weren't all protected by a GFCI as they are required to be. It was my son David who got the severe shock from a wet extention cord. :( This is what the system was designed to prevent.

My point: Trust, but verify! It pays to know and follow the rules.
 
All that was in there were two blacks and a ground. So both blacks are hot?

And, if I throw the MAIN breaker, does that remove all power from those bus bars in the panel, and allow me to do about anything I'd need to do in that panel?
Both blacks are supposed to be hot. The white is the neutral and goes to the neutral buss bar in the breaker box. What you don't have is a green ground wire which also goes to the neutral buss bar in the breaker box. Do you need the green ground wire? Perhaps yes, perhaps no. Depends on what your local codes says. In some locals, if you work on any segment of electrical wiring - that portion of the project has to meet current electrical code.

Throwing the main breaker is supposed to disconnect all circuits in the breaker box.

NOTICE I SAID SUPPOSED TO in both statements: Double check with a test light or multimeter before sticking your hands in the box.

Stop by your local library. They should have several "how to books" with pictures of various electrical wiring circuits - and clear diagrams of the various circuits.

Eugene
 
If you opt to throw the main breaker, shut all the other breakers off individually and then throw the main. This will keep you from throwing a large breaker under load. Do the reverse when turning things back on, turn the main on first then the individuals.
 
Naw, Eugene - I don't have a neutral at the cooktop end. Well, let's put it this way - none of the wires are white. I've got two blacks, and an uninsulated copper ground. That's it. I ain't checked at the breaker box end - but I'd think it would be the same out there. I've called the 3rd electrician this morning, but so far he hasn't called me back.
 
paw's49":1hyqnr0z said:
I tell ya, those are some big fat wires :D - I don't know if I could get one of them wrapped around those outlet screws or not!!

House built in 1971-all electric-could be aluminum wiring, YUK!

Peter
 
Back
Top