Don't do what they do on the TV......

BigBill

501 Club
Don't do what you see on the TV at Orange County Choppers, remember these guys were iron workers. I cringe everytime i see them beat ball bearings or roller bearings into there races to get something like the steering necks(example) together. Beating a bearing in the direction of the two races will put small dings into the races causing galling and fretting down the road besides binding when you try to steer or the shafts turn. "Do Not Do What They Do at Home"!!!!!!!!!!!!!!!!! I've tested so many gear boxes and seen bearings installed the wrong direction that failed in 1 or 2 days on the test dyne. Some of the ball bearings have opening were there assembled with the half moons in each mating race were if installed in the wrong direction this assembly opening gets hammered by the balls everytime a ball goes by the half moons. Its seening a side thrust load in that direction and if the bearing is put in backwards that half moon opening can hammer the balls to a short lived life and to a very fast failure(death). So beating on the bearing against its race can start the bearing on the way to failure too. Its pretty much the same failure too.

Handle bearings very carefully, don't unwrap them to look at them until your ready to install them so there kept clean, as clean as possible. You push in ball bearings y the outer race only. If you don't have the installing sleeve i use a large socket as the driver to press it into place. Please do not hammer on the inner race, again this will make galling marks in the inner and outer race and start the galling/fretting process and lead to premature bearing failure down the road.

Sometimes i can't believe what i see on the TV. At OCC they cut and grind on exhaust pipes and bike frames near the exhaust ports and weld splatter is near them too. When a four stroke engine cycles there is a short time when the exhaust port will suck or does an inhale before the intake cycle starts. It can inhale anything thats in the port(grindings/weld splatter) into the cylinders at this time so its very important what we do near and around the engines, mufflers, exhaust pipes and manifolds. Don't forget when grinding steel your grinding small steel particals plus the grinding wheel grit too. I cringe again when i see them doing this on the custom bikes. They would never make it in my world of machine building. There bikes are nice but there assembly process needs work.

When working on hydraulics keeping it squeeky clean is very important too. The biggest failures in hydarulics is dirt and over heating. Keep your assembly area clean when assemblying hydraulics and your hands too. You need to use lint free towels too. Lint/dirt can raise hell with hydraulic spool valves. Do it once and do it right.
 
Big Bill, you are right on your observation of their bad techniques. My professional life has been in "power transmission" since 1971. I have sold bearings, gearboxes, sprockets, motors and about everything in between for the Industrial world. I have cringed when watching shows like Orange County Chopper not only for their bad assembly style, but for their general nasty disposition. I used to watch just to see the finished product, but, now I can't even stand to see them due to the stresses they put on themselves. Not a happy lot.
Those guys on the show should go to a Cub gathering and see what real people are about. They live in a different world. Thanks for your observation and good advice regarding bearings and such! Steve K.
 
I thought they used a mock up motor and trans to fabricate the frame, ext and such, then installed the real motor after everything was painted. I think they fight and carry on to keep the attention of the audiance
 
Bigbill offers good advice above. I just rebuilt the water pump on a 140 Farmall. Even the service manual gets it wrong on reassembly procedure. Pressing out the old bearing/shaft assembly requires pressing the shaft as no other place is available for applying the necessary pressure. The manual says to just slip the new assembly into the housing. It requires the press. A 22mm deep socket was the best fit from my tool box to fit the outer race and fit inside the pump housing bore. Work carefully with bearings.
 
Those engines come in from a custom engine builder and there not cheap. At onetime they were buying the engines from Canada too but i forget the name of the company. I think alot of bike builders use the place in Canada for engines.

One more thought about installing new seals on shafts too. I like to prelube the seals in the double lip with grease or oil first then install it. This way the shaft is lubed were the seal is going to ride. I never install them dry because it takes too long for the lube to get into them before they burnout. Don't beafraid to lube the outside of the seal with a little silicone or oil when you install it this way it won't grab and freeze on the way in. I make sure my outer bearing races are lubed too. On some of the machines were the outer races were a tighter fit we would heat up the bores and put the bear races in a freezer then put them together. The bearing races would fall right in so we would spin them by hand so they would seat on the bottom of the bore. If we didn't spin them the race could rise up as it becomes room temperature. Just a few spins to make sure its down all the way in the bore. I'm very careful with new bearings and seals.

There welding and grinding around the engine thats for that bike. To me they should have a "clean room" for assembly so all the heavy fabrication like cutting, welding and grinding won't get into the rest of the parts. I've seen running dirty air cleaners let dirt into the cylinders and score them so what do you think the metal grindings, grinding wheel dust or welkd splatter will do when it gets into the cylinders? That first turn over with the starter i'm sure the exhaust will suck some of that crap into the cylinder in a split second. It doesn't take much to use a welding blanket or old welding gloves to protect the parts from damage. If i had to work,weld near parts and i had no choice i would stuff them with clean rags first, then cover them with welding gloves then cover them with a welding blanket or welding jacket. Then I'm sure there protected.

I've worked in companies that had clean rooms that were temperature controlled for bonding chrome liners for bearing ways on the machine beds with epoxy's. These rooms were as clean as hospital operating rooms.

I got introuble once working at a dealership for washing my tools at the end of the week in the parts washer to remove all the dirt and grime from them. I still did it for many years as a mechanic, every week i would wash my tools on a friday afternoon when all the work was done. I even greased all my ratchets too.

If your not sure just ask here someone will help you or guide you threw it. I'm not the sharpest tool in the shed but failure is not an option.
 
A lot of good advice BigBill, but I would add one thing. There are some seals that are to be installed dry and run dry for a specified amount of time so they seat properly. I don't remember which ones for sure but I think some water pump seals are that way and maybe some others.
 
I forget the name of those water pump spring loaded seals there also used on the honda dirtbikes too on the water pumps.
 
In regards to Orange County Sledge and slop: They stage all that junk to get an audience. I hope everyone can see thru this bunch. Also the Repo people are a hoax. They would be arrested for their actions toward the people they deal with. Just entertainment from the bottom feeders. Like the fella above said: You want good, real, honest mechanical help keep your little nose pinned to Cub Forum we are for real , Thomas at the Fantasy Farm.
 
Back
Top